wheel AUDI A4 2000 B5 / 1.G Brakes Read Mesure Value Block Workshop Manual

01-63
Test table: display group 1
Notes:

Display fields 1 through 4 show the current wheel circumference speeds in km/h. These are calculated by the ABS control
module -J104- on the basis of the signals received from the wheel speed sensors. If one of the display fields shows no
reading, proceed as for DTCs 00283, 00285, 00287, 00290 "ABS Wheel Speed Sensor" DTC table page 01
-98
.
In order to check whether wheel speed sensors are properly allocated to each wheel, the vehicle must be raised. On
vehicles with manual transmission put the gear shift lever in neutral. On vehicles with automatic transmission move the
selector lever to position "N". Turn appropriate wheel by hand. Remaining drive wheels must be secured against turning.
When a vehicle is accelerated uniformly on a dry surface, the displayed value will increase continuously by whole
numbers; e.g. 6 km/h, 7 km/h, 8 km/h ... . The difference between displayed values 1 to 4 should not be more than 1
km/h (error from out-of-round wheels). If the values jump, for instance from ...6km/h, 7 km/h, to 12 km/h...or if the
difference between the displayed values is greater than 1 km/h, then check the installation of the wheel speed sensors
and rotors. Repair Manual, Suspension, Wheels, Steering, Repair Group 40

Repair Manual, Suspension, Wheels, Steering, Repair Group 42

Read measuring value block
1
Indicated on display
1 to 19
1)
km/h 1 to 19
1)
km/h
1 to 19
1)
km/h 1 to 19
1)
km/h


Rear right wheel circumference speed

Rear left wheel circumference speed
Pa
ge 3 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

Front right wheel circumference speed
Front left wheel circumference speed 1) On Board Diagnostic (OBD) is terminated by the ABS control module -J104- if road speed exceeds 19 km/h.
Pa
ge 4 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-65
Test table: display group 2 Read measuring value block
2
Indicated on display
0 or 1
0 or 1

0 or 1
0 or 1



ABS solenoid valve relay:
For vehicles with Front Wheel Drive (FWD), the display shifts one field toward
left.
0 not permitted during "Read measuring value block", the relay was not
activated during "ignition on".
- Carry out "Electrical test", step 11 page 01
-68
.
1 specified value, relay was activated by ABS control module -J104- during
ignition on.

Voltage at motor for ABS return flow pump:
For vehicles with Front Wheel Drive (FWD), the display shifts one field toward left.

0 specified value, there is no voltage at the motor for the ABS return flow pump. 1 not permitted during "Read measuring value block", there is voltage at the motor for the
ABS return flow pump.
- Carry out "Electrical test", step 12 page 01
-68
.

Brake light switch: Additional signal only for
All Wheel Drive (AWD):
Pa
ge 6 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

0 Brake pedal not operated1 Brake pedal operated

Electrical Wiring Diagrams, Troubleshooting & Component
Locations - Check brake light switch if there are deviations.
Brake light switch: Signal for Front
and All Wheel Drive:

0 Brake pedal not operated 1 Brake pedal operated


Electrical Wiring Diagrams, Troubleshooting & Component Locations - Check brake light switch if there are deviations.
Pa
ge 7 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

- If no indication is displayed, proceed according to DTC 00529 "Wheel speed information missing. No signal". DTC table
page 01
-98
.
Pa
ge 10 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-69


Note:
The operation manual for the VAS1978 wiring harness repair kit generally
forbids the repair of any lines in the ABS or related systems. This rule only
pertains to the shielded lines in these systems.
Multi-pin harness connector for ABS control module -J104- in proper
condition, with no bent, broken or corroded terminals. Replace any
damaged terminals using VAS1978 wiring repair kit. Ignition and electrical consumers switched off before beginning
testing (headlights, lighting, fan, etc.). For steps 13 through 16, raise the vehicle until the wheels rotate
freely. On vehicles with manual transmission put the gear shift lever in
neutral. On vehicles with automatic transmission move the selector
lever to position "N".
Pa
ge 12 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-72
Terminal assignment of multi-pin connector for wiring harness / ABS control module (w/EDL) -J104- Terminal
Wire connection to component ...
1
Voltage supply, terminal 15 2
Hydraulic unit; activation of ABS return flow pump relay -J105- 3
Hydraulic unit; left front traction control switch-over valve -N168- (secondary piston circuit) 4
Hydraulic unit; left front traction control outlet valve -N169- (secondary piston circuit) 5
Hydraulic unit; left front ABS inlet valve -N101- 6
Hydraulic unit; right rear ABS inlet valve -N133- 7
Hydraulic unit; activation of ABS return flow pump relay -J105- 9
Left front ABS wheel speed sensor -G47-
for vehicles with Front Wheel Drive (FWD) and ABS/EDLfor vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
10
Left front ABS wheel speed sensor -G47- 11
Right rear ABS wheel speed sensor -G44- 12
Left rear ABS wheel speed sensor -G46- 13
Left rear ABS wheel speed sensor -G46- 14
Right front ABS wheel speed sensor -G45- 15
Right front ABS wheel speed sensor -G45-
for vehicles with Front Wheel Drive (FWD) and ABS
Pa
ge 15 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

for vehicles with Front Wheel Drive (FWD) and ABS/EDLfor vehicles with Front Wheel Drive (FWD) and ABS/EDL (ABS pressure regulation)
Pa
ge 16 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

01-73

Terminal
Wire connection to component ...
18
Engine Control Module (ECM); MMD signal (Masked Misfire Diagnostic)
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR, the SET signal (Specified Engine Torque) is
also transmitted via this wiring harness.
19
Hydraulic unit; control wire for ABS return flow pump -V39- 20
Engine Control Module (ECM); Engine RPM
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
25
Hydraulic unit; Left rear ABS outlet valve -N136- 26
Hydraulic unit; Right front ABS outlet valve -N100- 27
Hydraulic unit; right front traction control outlet valve -N167- (primary piston circuit) 28
Ground (GND) terminal 31 (ABS control module -J104-) 29
Ground (GND) terminal 31 (ABS control module -J104-) 31
Instrument cluster; activation of traction control indicator light
for vehicles with Front Wheel Drive (FWD) and ABS/EDL/ASR
32
Instrument cluster; ABS/EDL warning light activation (active) 33
Hydraulic unit; Left front ABS outlet valve -N102- 34
Hydraulic unit; Right rear ABS outlet valve -N135- 35
Left front ABS wheel speed sensor -G47-
for vehicles with All Wheel Drive (AWD) and ABS/EDL
Pa
ge 17 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8

36
Left front ABS wheel speed sensor -G47-
for vehicles with Front Wheel Drive (FWD) and ABS
Pa
ge 18 of 79 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.8