oil AUDI A4 2015 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: A4, Model: AUDI A4 2015Pages: 304, PDF Size: 74.86 MB
Page 217 of 304

Using the proper engine oil is important for
the functionality and service life of the en
g ine. Your engine was factory -filled with a
h igh-quality oil which can usually be used
t h roughout the entire year.
Your Limited New Vehicle Warranty does not cover damage or ma lf u nctions due to
fa ilure to follow recommended mainte
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty
&
Ma intenance booklet .
- Use only a high quality eng ine oil that ex
pressly complies w ith the Audi o il quality
sta ndard specified for your veh icle's e n
gine . U sing any other oil can cause seri
ous eng ine dam age.
- Do not m ix any l ubrica nts o r othe r addi
tives into the eng ine oi l. Doing so can
ca use eng ine damage.
I f you need to add oil and there is no ne
availab le tha t mee ts the Audi o il qua lity
s t andard your engine requires, yo u may
add a tota l of no more than 0 .5 quart/ liter
of a high -quality "synthetic"oil t hat meets
the following specifications.
- Vehicles with gaso line engine: ACEA A3
or API S M with a viscosity grade of
SAE 0W-30, SAE SW-30 or SA E SW-40.
- For more information abo ut eng ine oil
that has been app roved for your vehicle,
please contact either your a uthori zed
Audi dealer or Audi Customer Relations
at 1 (800) 822 -2834 or visit our web site
at www.a udiusa .com or
www .aud icanada .ca .
Engine oil consumption
The engine in your vehicle depends on an ade
quate amount of oil to lubricate and cool all
of its moving parts.
In order to provide effective lubrication and
cooling of inte rnal engine components, all in-
~ ternal combustion eng ines consume a certai n ,....,
Checking and fillin g 215
amoun t of oil. Oil consumpt ion varies from
engine to engine and may change significantly
over the life of the engine . Typically, engines
with a spec ified break-in period (see
¢
page 193) consume more oil during the
break -in period than they consume after o il
consumption has stabilized .
U nder normal cond itions, the rate of oil con
sumption depends on the quality and viscos ity
of the oil, the RPM (revolutions per minute) at
which the engine is operated, the ambient
temperature and road conditions. Further fac
tors are the amount of oil dilut ion from water
condensa tion or fue l resid ue an d the oxida
t ion level of the o il. As any engine is subject to
wear as mi leage b uilds up, the oil consump
tion may increase over time until replacement
of worn components may become necessary.
With a ll these variab les coming into p lay, no
standard rate of oil consumption can be es
tablished or specified. There is no alternative
to regular and frequent check ing of the o il lev
el, see
Note .
If the yellow engine oil leve l warning symbo l
El in the instrument cl uster lights up, you
sho uld check the oil leve l as soon as possib le
¢
page 216. Top off the oil at your earliest
convenience
¢ page 216.
A WARNING
Before you c heck anythi ng in the engine
compartmen t, always read a nd heed all
WAR NINGS ¢&.
in Working in the engine
c ompar tment on page 212.
(D Note
D riving w it h an insufficient o il level is like
l y to cause sever e damage to the e ngine .
(D Tips
- The oil pressure warning display. is
not an indicator of the oil level. Do not
rely on it. Instead, check the oil level in
your engine at regular intervals , pref
erably ea ch time you r efuel, and alway s
before going on a long trip . .,.
•
•
Page 218 of 304

216 Checking and filling
-If you have the impression your engine
consumes excessive amounts of oi l, we
recommend that you consult an author
ized Audi dealer to have the cause of
your concern properly diagnosed. Keep in
mind that the accurate measurement of
oil consumption requires great care and
may take some time . An authorized Audi
dealer has instructions about how to
measure oil consumpt ion accurately.
Checking the engine oil level
Fig. 183 MMI D isp lay : Oil leve l ind icator
Read oil level
.,. Park your vehicle so that it is horizonta lly
level.
.,. Shut the engine off when it is at operat ing
temperature .
.,. Switch only the ignition back on.
• Wait approx . two minutes.
• Se lect : Fu nct ion button
I _C_A_R_I > Oil level. Or
.,. Select : Function button
ICARI > Car sys-
tems* control button > Servicing & checks >
Oil level.
.,. Read the oil Level in the MMI* Display
c:> fig. 183. Add engine oi l if the bar of the
oil level indicator is near "min"
c:> page 216
Depend ing on the way the vehicle is driven
and the operating conditions, oil consumpt ion
can be up to a 1/2 quart per 600 mi les (0.5
li
ter per 1,000 km) . Consumption may be high
er within the first 3,000 miles (5 ,000 km).
(D Tips
The oil Level indicator in the MMI* Display
is only an information display . If the oil
Level is too Low, a minimum oil warning ap -pears in
the instrument cluster. Add oil
c:> page 216. If the hood has been opened,
the current oil level is shown in the instru
ment cluster the next t ime the ignition is
switched on.
'e:;1: Adding engine oil
Fig. 184 Engin e compar tmen t: Cover on th e oil filler
neck
.,. Before you check anything in the engine
compartment,
always read and heed all
WARNINGS c:> .&. in Working in the engine
compartment on page 212 .
.,. Shut the engine off .
.,. Unscrew the cap
't'::71 to the engine oi l filling
hole
¢ fig. 184, c:>page 214, fig. 182 .
.,. Carefully top off with 0 .5 quarts (0 .5 liters)
of the appropriate oil
c:> page 214 .
• Check the oil level again after two minutes
r::;, page 216, Checking the engine ail level .
.,. Top off the oil aga in , if necessary .
.,. Screw the cap back on the filling hole .
_& WARNING
-While topping off, the oil must not come
i n contact with hot engine parts -fire
hazard!
- The oil filler cap must be properly se
cured to prevent oil from being sprayed
on the hot engine and exhaust system
when the engine is running -fire hazard!
- If your skin has come in contact with the
engine o il, you must subsequently
cleanse it thoroughly.
(D Note
- Check the oil level using the radio or
MMI*. If the message Please reduce oil
Page 219 of 304

"" N
0 ::.,: co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
level appears, contact your authorized
A udi dealer or qualified workshop to
have excess oil ext racted if necessary.
- Audi does not recommend the use of oil
additi ves. They may damage the engine
and ad ve rsely affect your New Vehicle
Warranty.
@) For the sake of the environment
- Under no circ umstances ca n the o il come
i n contact with the sewage network or
the soil.
- Observe and fo llow lega l regu lations
when disposing of empty oil containers.
Changing the engine oil
We recommend thot hove your oil changed by
an authori zed Audi dealer or a qualified serv
ice station .
Before you c hec k anything in the engine com
pa rtment,
always read and heed all WARN
INGS
c:> A in Working in the engine compart
ment on page 212.
The engine oil must be changed according to the intervals specified in your Warra nty
&
Maintenance book let . This is very important
beca use the l ubricating properties of oil di
minish gradua lly dur ing normal veh icle use .
Unde r some c irc umstances the engine o il
should be changed more frequently . Change
oil more often if you drive m ost ly short dis
tances, operate the vehicle in dusty areas or
u nder predominantly stop-and-go t raff ic con
d it ions, or have your veh icle w her e tempera
tures rema in below free zing fo r ex tended pe
rio ds.
Detergent add itives in the o il w ill mak e fresh
oil look da rk after the eng ine has been run
ni ng fo r a shor t time. This is norma l and is not
a reason to ch an ge the oi l mo re often th an
recommended.
B ecause of the prob lem of prope r dispos al,
a long w ith the spe cial tools and necessary ex
pe rti se require d, we strong ly recommend tha t
Checkin g and fillin g 217
you have your oil changed by an a uthorized
Audi deale r or a qualified service station.
If you choo se to change your oil your self ,
please note the fo llow ing important info rma
t ion :
A WARNING
To reduce the risk of pe rsonal i njury if you
must change the eng ine oil in yo ur vehicle
yourself:
- Wear eye protect ion .
- To reduce t he risk of burns from hot en -
gine oil, let the engine coo l down to the
touch .
- W hen removi ng the oil dra in plug with
your fingers, stay as fa r away as possib le .
A lways keep your fo rearm parallel to the
groun d to help p revent hot o il from run
ning down you r arm .
- Dra in the oil into a c ontaine r designed
for this purpose, one large enough to hold at least the tota l amount of oi l in
your engin e.
- Eng ine oil is poison ous. Keep it we ll out
of the reach of childre n.
- Continu ous contact wit h used eng ine oi l
is harmful to yo ur sk in. Always protect
your skin by washi ng oil off tho ro ughly
w it h soap and wate r.
(J) Note
Neve r mix oil additives with yo ur engine
oi l. These additives can damage your en
g in e and adversely affect you r Aud i Limit
ed New Veh icle Warranty.
@ For the sake of the environment
-Before changi ng your oil, first make su re
you know where you ca n prope rly dispose
of the us ed oil.
- Always disp ose of used eng ine o il proper
ly . D o not dump it on garde n soil, wood
e d ar eas, into op en st reams o r down
sewage drain s.
- Recycle used engi ne oil by taking it to a
used eng ine oil collect io n facility in you r
a rea, or contact a service sta tio n.
•
•
Page 220 of 304

218 Check ing and filling
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro
tects the engine from freezing in the winter .
The cooling system is sealed and generally re
quires little attention.
The cooling system has been filled at the fac
tory with a permanent coolant which does not need to be changed. The coolant consists of a
mixture of specially conditioned water and the
manufacturer's glycol-basedcoolant addi-
tive G13 antifreeze with ant icorrosion addi
tives (50% for USA models; 60% for Canadian models) . This mixture both assures the neces
sary frost protection and protects metal com
ponents in the engine's cooling system from
corrosion and scaling.
It a lso raises the boil
ing point of the coo lant.
Do not reduce the concentration of the coo l
ant in the summer by adding plain water .
The
pr opor tion of coolant add itiv e m ust be at
l eas t 50% but not more than 60%
to main
tain antifree ze protection and cooling efficien
cy. If the coolant frost protection is too low,
the coolant could freeze and damage the veh i
cle heating and eng ine cooling system .
For year-round driving, antifree ze is added at
the factory for temperatures down to:
- -31°F(-35°C)USA
- - 40 ° F ( - 40 °C) Canada.
I f you must add coo lant, use a m ixture of wa
ter and coolant addit ive. M ixing the coolant
addit ive with dist illed water is recommended.
_& WARNING
Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~ &. in Working in the engine
compartment on page 212.
(D Note
- Before winter sets in, have the coolant
checked to see if the coolant additive in
-
your vehicle is sufficient to meet the climate conditions . This is especia lly impor
tant if you live in a reg ion where the win
ter is extreme ly cold. If necessary, in
crease the proportion of coolant additive
to 60% .
- When adding coolant additive to your
cooling system, remember :
- We recommend us ing on ly coolant ad
d itive G12 ++ or G13 for your vehicle.
This coolant addit ive is availab le at a u
thorized Audi dealers. Other types of
antifreeze can significantly reduce cor rosion protection. The resulting corro
sion can cause a loss of coolant and se
rious engine damage .
- Do not add any type of radiator leak seal
ant to your vehicle's engine coolant.
Add ing radiator repa ir flu id may adverse
ly affect the function and performance of
your cooling system and could resu lt in
damage not covered by your New Veh icle
Limited Warranty.
Checking the engine coolant level
The engine coolant level can be checked with
a quick glance.
F ig . 1 85 Engine compar tmen t: Cover on the coo la n t
expans io n t ank
.,. Before you check anything in the engine
compa rtment,
alwa ys read and h eed all
W ARNING S ~ ,& in Working in the engine
compartment on page 212.
.,. Park your vehicle on a level surface .
.,. Turn off the ignition.
.,. Read the engine coolant level from the coo l
ant expansion tank
c:> fig . 185, c:> page 214,
fig . 182.
With a cold engine, the coolant Iii>-
Page 221 of 304

'"" N
0 ::.,: co ,...., \!) ..,.,
,...., ..,., ,....,
level should be between the "MIN" and
"MAX" markings. When the engine is warm,
the level may be slightly above the "MAX"
marking .
The location of the coolant expansion tank
can be seen in the engine compartment illus
tration
<=> page 214.
To obtain an accurate reading , the engine
must be switched
off.
The expansion tank in your vehicle is equipped
with an electric coolant level sensor.
When the coolant level is too low, the warning
light in the Auto-Check System <=>
page 17 will
blink until you add coolant and the level has
been restored to normal. Even though there is
an electric coolant level sensor, we still rec
ommend you check the coolant level from
time to time.
Coolant loss
Coolant loss may indicate a leak in the cooling
system. In the event of coolant loss, the cool
ing system should be inspected immediately
by your authorized Audi dealer.
It is not
enough merely to add coolant.
In a
sealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheating.
A WARNING
The cooling system is under pressure and
can get very hot. Reduce the risk of scald
ing from hot coolant by following these
steps.
- Turn
off the engine and allow it to cool
down.
- Protect your face, hands and arms from escaping fluid and steam by covering the
cap with a large, thick rag .
- Turn the cap slowly and very carefully in
a counter-clockwise direction while ap
plying light, downward pressure on the
top of the cap .
- To avoid being burned, do not spill anti
freeze or coolant on the exhaust system
Checking and filling 219
or hot engine parts. Under certain condi
tions, the ethylene glycol in engine cool
ant can catch fire.
([) Note
Do not add any type of radiator leak seal
ant to your vehicle's engine coolant. Add- ing radiator repair fluid may adversely af
fect the function and performance of your
cooling system and could result in damage
not covered by your New Vehicle limited
Warranty .
Adding coolant
Be very careful when adding engine coolant.
Before you check anything in the engine com
partment ,
always read and heed all WARN
INGS <=>
A in Working in the engine compart
ment on page 212 .
Requirement: There must be a residual
amount of coolant in the expansion tank <=>(D.
.,. Turn
off the engine.
.,. Let the engine cool down.
.,. Place a thick rag over the coolant expansion
tank
<=> page 218, fig . 185 and carefully turn
the cap counter-clockwise
<=> .&_ .
.,. Add coolant mixed in the correct ratio
<=> page 218, Coolant up to the MAX mark
ing.
.,. Make sure that the fluid level remains sta-
ble. Add more coolant if necessary.
.,. Twist the cap on again
tightly.
Replacement engine coolant must conform to
exact specifications <=>
page 218, Coolant.
We recommend using only coolant additive
G12 ++, G13 or in an emergency G12 +. Do
not
use a different additive. In an emergency use
plain water until you can get the correct addi
tive and can restore the correct ratio. This
should be done as soon as possible.
If you have lost a considerable amount of
coolant , then you should add cold antifreeze
and cold water only when the engine is cold.
Always use
new engine coolant when refilling . .,.
•
•
Page 223 of 304

M N
~ co
rl I.O
"' rl
"' rl
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
N
N
;:;;
" 03
"'
Fi g. 186 Eng ine compartment: Cover on the brake flu
id reservoi r
Before you check anything in the engine com
partment,
a lwa ys read and heed a ll W ARN
ING S c:> .&.. in Working in the engine compart
ment on page 212 .
~ Read the brake fluid level from the brake
fluid reservoir
c:> fig. 186, <=> page 214,
fig . 182.
The brake flu id level must be be
tween the "MIN" and "MAX" markings.
The brake fluid reservoir is located at the rear
partition of the engine compartment on the
left side
<::;> page 214 .
The fluid level may drop slightly after some
time due to the automatic adjustment of the
brake pads . This is not cause for alarm .
If the brake fluid level falls
considerably be
low the "MIN" mark, the brake warning/indi
cator light (U.S. models:~, Canadian
models: .) will come on
r:> page 15. Do not
continue to operate the vehicle. The complete b rake system shou ld be thoroughly checked
by an authorized A udi dealer or qualified
workshop and the cause co rrected . If the
b rake fluid level is too low, the brake warn ing/
indicator light w ill illuminate. Contact an au
thorized Audi dealer
immediately .
@ Tips
The brake f luid reservoir is located under
neath the cover .
Checking and fillin g 221
Changing brake fluid
Have the brake fluid changed by an experi
enced technician.
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too
high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also dec rease considerably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
every two years. Always use new brake flu id
which conforms to Federal Motor Vehicle
Standard "F MVSS 116 DOT 4".
The brake fluid reservo ir can be d iff icult to
reach, the refore, we recommend that you
have the brake fluid changed by your author
i zed
Audi d ealer. Your dealer has t he correct
tools, the right brake fl uid and t he know-how
to do this for you .
A WARNING -.
-Brake fluid is poisonous . It must be stor
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap
propriate brake f luid. Observe these pre
cautions:
- Use only brake fluid that meets SAE
spe cificat ion
J 1 7 03 and conforms to
Federa l Moto r Ve hicl e Standard 116.
Always check with yo ur authorized Audi
dealer to make sure yo u are using the
correct bra ke fluid. The correct type of
brake f luid is also indicated on the
brake f luid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
l ong. This can seriously affect the effi
c iency of the brakes as well as your
safety. Th is cou ld resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .
Page 229 of 304

Tires and wheels
Tires
General notes
Tires may be the least appreci
ated and most abused parts of
a motor vehicle .
Tires may be the least appreci
ated and most abused parts of
a motor vehicle. Tires are, how
ever, one of the most important
parts of a vehicle, particularly
considering the comparatively
small patch of rubber on each
tire that assures that all-impor
tant contact between you, your
vehicle and the road.
Maintaining the correct tire
pressure, making sure that your
vehicle and its tires do not have
to carry more weight than they can safely handle, avoiding
damage from road hazards and
regularly inspecting tires for
damage including cuts, slashes
irregular wear and overall con
dition are the most important
things that you can do to help avoid sudden tire failure includ
ing tread separation and blow-
~ outs.
0 ::.,: co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Tires and wheels 22 7
Avoiding damage
If you have to drive over a curb
or similar obstacle , drive very
slowly and as close as possible
at a right angle to the curb.
Always keep chemicals includ ing grease, oil, gasoline and
brake fluid off the tires.
Inspect the t ires regularly for
damage (cuts, cracks or blis
ters, etc.). Remove any foreign bodies embedded in the treads.
Storing tires
Mark tires when you remove
them to indicate the direction
of rotation. This ensures you to be able to mount them correct
ly when you reinstall them.
When removed, the wheels or
tires should be stored in a cool, dry and preferably dark place.
Store tires in a vertical position if they are not mounted on
rims, in a horizontal position if
they are mounted on rims.
New tires
New tires have to be broken in
¢ _&..
The tread depth of new tires
may vary , according to the type .,.
•
•
'
Page 232 of 304

230 Tires a nd whee ls
Bead Extra load tire
means the part of the tire that means a tire design to operate
is made of steel wires, wrapped at higher loads and at higher
or reinforced by p ly cords and inflation pressures than the
that is shaped to fit the rim . corresponding standard tire .
Bead separation Extra load tires may be identi-
fied as "XL", "xl", " EXTRA
means a breakdown of the bond LOAD", or "RF" on the sidewall.
between components in the
bead .
Gross A xle Weight Rating
(" GAWR ")
Cord
means the load-carrying capaci-
means the strands forming the ty of a single axle system,
p lies in the tire .
measured at the tire-ground in-
Cold tire inflation pressure terfaces.
means the tire pressure recom-
Gross Vehicle Weight Rating
mended by the vehicle manu-( "GVWR ")
facturer for a t ire of a designat-
means the maximum total
ed size that has not been driven loaded weight of the vehicle.
for more than a couple of miles
Groove
(kilometers) at low speeds in
the three hour period before means the space between two
the tire pressure is measured or adjacent tread ribs.
adjusted.
Load rating (code )
Curb weight
means the max imum load that
means the weight of a motor a tire
is rated to carry for a giv-
vehicle with standard equip -en inflation pressure
. You may
ment including the maximum not find th
is information on all
capacity of fuel, oil, and cool- tires because it is not required
ant, air condit ioning and addi- by law.
...
tional weight of optional equip-
ment.
Page 245 of 304

Tires and wheels 243
and can lead to sudden tire fail- The Gross Axle Weight Rating •
ure, including a blowout and ("GAWR") is the maximum load • '
sudden
deflation that can cause that can be applied at each of
the vehicle to crash. the vehicle's two axles.
Your safety and that of your The Gross Vehicle Weight Rat- passengers also depends on ing and the Gross Axle Weight
making sure that load limits are Rating are listed on the safety
not exceeded. Vehicle load in- compliance sticker label locat-
eludes everybody and every- ed on the driver's side B-pillar.
thing in and on the vehicle. Your Audi has 5 seating posi-
These load limits are technical- tions, 2 in the front and 3 in the ly referred to as the vehicle's rear for total seating capacity
Gross Vehicle Weight Rating of 5. Each seating position has
("GVWR"). a seat belt¢
page 136~ Safety
The "GVWR" includes the belts.
weight of the basic vehicle, all The fact that there is an upper
factory installed accessories, a limit to your vehicle's Gross Ve-
full tank of fuel, oil, coolant hicle Weight Rating means that
and other fluids plus maximum the total weight of whatever is
load. The maximum load in- being carried in the vehicle (in-
eludes the number of passen- eluding the weight of a trailer
gers that the vehicle is intend- hitch and the tongue weight of
ed to carry ("seating capacity") the loaded trailer) is limited.
with an assumed weight of The more passengers in the ve- 150 lbs. (68 kg) for each pas- hicle or passengers who are
senger at a designated seating heavier than the standard
position and the total weight of weights assumed mean that
any luggage in the vehicle . If less weight can be carried as
you tow a trailer, the weight of luggage. the trailer hitch and the tongue The tire pressure label on your
'"" weight of the loaded trailer N
Audi also lists the maximum 0 ::.,:
must be included as part of the co .... combined weight of all of the \!) 1.1'1
vehicle load . .... 1.1'1 ....
Page 249 of 304

Incorrect wheel alignment
Incorrect wheel alignment can
cause excessive tire wear, im
pairing the safety of the vehi
cle. If tires show excessive
wear, have the wheel alignment checked by an authorized Audi
dealer or qualified workshop.
All wheel drive
Vehicles with quattro must al
ways have tires of the same size, construction and tread
type. For details see
¢ page 190 .
A WARNING
Sudden tire failure can lead
to loss of control, a crash and
serious personal injury!
-Never drive a vehicle when the tread on any tire is worn
down to the wear indica
tors.
-Worn tires are a safety haz ard, they do not grip well on
wet roads and increase your risk of "hydroplaning" and
loss of control.
- Always keep chemicals that
can cause tire damage, such
as grease, oil, gasoline and brake fluid away from tires.
-
Tires and wheels 24 7
-Tires age even if they are not being used and can fail
suddenly, especially at high
speeds. Tires that are more
than 6 years old can only be
used in an emergency and
then with special care and at lower speeds.
-Never mount used tires on your vehicle if you are not
sure of their "previous histo ry ." Old used tires may have
been damaged even though
the damage cannot be seen
that can lead to sudden tire
failure and loss of vehicle
control.
•
•
'