key AUDI A5 CABRIOLET 2014 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2014, Model line: A5 CABRIOLET, Model: AUDI A5 CABRIOLET 2014Pages: 286, PDF Size: 70.4 MB
Page 50 of 286

48 Power top
Step 3: Lifting the power top storage
bay cover out
Fig. 4 3 Luggage compartment lid closed
Fig. 44 Power top sto rage bay cover completely open
... Close the luggage compartment lid .
11--Open the power top storage bay cover com
pletely
c::> fig. 44 .
..&, WARNING
When ra is ing the power top storage bay
cover, avoid con tact w ith the s upports o r
other moving parts . Othe rwise you cou ld
pinch your hands.
Step 4: Closing the power top
F ig . 4 5 Removi ng the cover
Fig. 46 Emergency key for ope ning the latches
11--Remove the cap on the trim .
11--Insert the emergency key in the open ing
(hex socket) .
11--Turn the release key counterclockwise until
it stops to open the latch .
... Remove the emergency key.
Step S: Closing the power top
The power top must be positioned by hand.
Fig . 47 Power top partially open
Fig. 4 8 Winds hie ld: Power top
11--Raise the power top out of the tray c::> .&. in
Step 2: Lifting the power top compartment cover out on page 47 .
11--Pull the power top out completely .
., Press the power top onto the windshield
frame
c::> fig . 48 .
Page 51 of 286

.. Press the switch ~ ¢ page 44, fig. 32 to
close the convertible top. If this does not
work, proceed w ith
¢ page 49, Step 6: Re
tracting the power top comportment cover.
Have a second person assist when posit ioning
the power top . That person should stand on
the opposite side of the vehicle and perform
the same steps.
A WARNING
- When positioning the power top, avoid
contact with the supports or o ther mov
ing parts. Otherwise you could pinch
yo ur hands .
- When pressing the power top down onto
the windsh ie ld frame, make su re that
you do not pinch yourse lf or anyone else .
Step 6: Retract ing the power top
compartment cover
The power top comportment cover must be
retracted by hand.
F ig . 49 Power top raised
-
.. Raise the rear of the power top and hold it in
place
i::> fig. 49 © i::> A in Step 2: Lifting the
power top compor tment cover out on
page 47 .
.,. Slide the power top compartment forward
u nti l it reaches the end position @. Release
the power top.
A WARNING
Do not pinch yo urself o r othe rs when clos
ing the power top compartment.
Power top 49
Step 7 : Locking the power top
The locking system for the power top latches
ore located on the inside of the power top .
Fig . SO In side of the powe r top : hex key fo r eme rgency
oper atio n
.. Insert the emergency key in the open ing and
turn it clockwise unt il it stops to lock the
power top .
.,. Remove the emergency key .
.. Cover the opening w ith the cap.
(D Tips
Make sure the locking mechanisms are
l ocked secure ly.
Step 8 : Loosen ing the headliner
F ig. 51 Power top: area around the rig ht s ide o f th e
rear window
F ig. 52 Area a ro un d t he r igh t sid e of th e rear w indow :
,._ 0 ,._ ~
>< co a,
headliner part ia lly loose ned •
Page 52 of 286

50 Power top
Perform the following steps in the rear win
dow area of the power top on each side .
.,. Pull the loops (marked in yellow) w ith the
eme rgency key to loosen the headliner .
.,. Pull at the yellow marking again to loosen
the headliner around the rear window (ap
proximate ly 30 cm).
Step 9: Securing the latch
Fi g. 53 Rear of the power top: Securing the latc h
The latches must be secured on the left and
right sides of the vehicle .
.,. Pull the power top headliner to the side in
the area around the rea r headrests to sec ure
the latches~
fig. 53 ~.&. in Step 2: Li~ing
the power top compartment cover out on
page 47 .
.,. Then remove the emergency key and insert
the short end into the power top support at
the yellow marking .
.,. Press the emergency key in the direction of
the arrow @ unt il the latch is secure .
A WARNING
Do not pinch yourself or others when clos
ing the power top compar tment.
Page 54 of 286

52 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
¢page 52.
- When you remove your key from the igni
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc
tion, the driver is no tified in the instru
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 55 Tu rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl us
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig
na l switches off au toma tically .
- The
high beam works on ly w hen the head
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.
Page 56 of 286

54 Clear vision
Interior lights
Front/rear interior lights
Fig . 57 Fro nt headliner : interior lighting controls
Fig. 58 Rear headlin er: rear reading lights
@ Interior lights
Press the button ®· T he LED in the button il
luminates.
If the LED illum inates, the interior lights turn
on automatically when you un lock the vehicle,
open a door or remove the ignition key. The in
ter ior lights turn off several seconds after
your close the doors, when you lock the vehi
cle or when you turn the ignition on. When a
door is open, the light turns off after a few
minutes .
@ Front/rear reading lights
To turn a reading light on/off, press the but
ton~¢
fig. 57or ¢fig. 58.
Instrument illumination
The basic brightness of the illumination for
the instruments, the center console and the
display can be adjusted.
Fig. 59 Instrument illumination
.,. Press the knob to release it .
.,. Turn the knob toward"-" or"+" to reduce or
increase the brightness .
.,. Press the knob aga in to return it to its origi
nal position.
(!') Tips
The instrument illumination (for dials and
needles) lights on when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, the illu
mination of the dia ls likewise dims auto
matically and will go out completely when
the outside light is very low. This feature is
meant to remind you to switch on the
headlights when outside light conditions
become poor.
Vision
Adjusting the exterior mirrors
Fig. 60 Forward section of driver's armrest: power mir
r or controls
Page 57 of 286

Turn the knob to the desired position:
Q/ P -In this position , you can adjust the
driver's and front passenger's exterior mirrors by turning the knob in the desired direction.
(ijjl -The mirrors are heated depending on the
outside temperature.
Passenger exterior mirror tilt function*
To help you see the curb when backing into a parking space, the surface of the mirror tilts
slightly . The knob must be in the P posit ion
for this to happen .
You can adjus t the tilted mirror sur face by
turning the knob in the desired direction .
When you move out of reverse and into anoth
er gear, the new mirror position is stored and
assigned to the key you are using.
T he mirror goes back into its original position
once you drive forward faster than 9 mph (15 km/h) or switch the ignition off .
_& WARNING
Curved mirror surfaces (convex or spheri
cal*) increase your field of view. Remem
ber that vehicles or other objects will ap
pear smaller and farther away than when
seen in a flat mirror. If you use this mirror
to estimate distances of following vehicles
when changing lanes, you could estimate
incorrectly and cause an accident .
(D Note
- If you wash the vehicle in an automatic
car wash, you must fold the exterior mir
rors in to reduce the risk of damage to
the mirrors.
{!) Tips
- The exterior mirror settings are stored
with the memory function*
c:> page 64.
-If there should be a malfunction in the
electrical system, you can still adjust the
exterior mirrors by pressing the edge of
the mirror.
.
Clear vision 55
Dimming the mirrors
N
~
><
~===~=======~ ~
Fig. 61 Auto matic dimmin g rearv iew mirro r*
Manual dimming rearview mirror
.,. Pull the lever on the bottom of the mirror
back .
Automatic dimming rearview mirror*
.,. Press the button @c:>
fig. 61. The indicator
light @ turns on . The rearview and exterior*
mirrors dim automatically when light shines
on them, for example from headlights on a
vehicle to the rear .
_& WARNING
-
Electrolyte fluid can leak from automatic
dimming mirrors if the glass is broken .
Electrolyte fluid can irritate skin, eyes and
respiratory system.
- Repeated or prolonged exposure to elec
trolyte can cause irritation to the respira
tory system, especially among people
with asthma or other resp iratory condi
tions . Get fresh air immediately by leav
ing the vehicle or, if that is not possible,
open windows and doors all the way.
- If electrolyte gets into the eyes, flush
them thoroughly with large amounts of clean water for at least 15 minutes;
medical attention is recommended.
- If electrolyte contacts skin, flush affect
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention
is recommended. Thoroughly wash af
fected clothing and shoes before reuse .
.
Page 63 of 286

close to this position as possible
¢page 63.
A WARNING
Never place any objects in the driver's foot
well. An object could get into the pedal
area and interfere with pedal function. In
case of sudden braking or an accident, you
would not be able to brake or accelerate .
Front passenger's seat
Always move the front passenger seat into
the rearmost position .
To avoid contact with the airbag while it is de
ploying, do not sit any closer to the instru
ment panel than necessary and always wear
the three-point safety belt provided adjusted
correctly . We recommend that you adjust the
passenger's seat in the following manner:
.,. Bring the backrest up to an (almost) upright
position.
Do not ride with the seat reclined .
"" Applies to vehicles with adjustable head re
stra ints: Adjust the head restraint so the up
per edge is as even as possible with the top
of your head. If that is not possible, try to
adjust the head restraint so that it is as
close to this position as possible
¢ page 63.
.,. Place your feet on the floor in front of the
passenger's seat .
Front seats
Power seat adjustment
Applies to vehicles: with power adjustable seats
Fig. 67 Front seats: power seat adjustment
Seats and storage 61
Controls
@-Adjusting the lumbar support*: press the
button in the corresponding position ¢
.&..
@ -Moving the seat up/down: press the but
ton up/down ¢ ,&. .
®-Moving the seat forward/back: press the
button forward/back¢ ,&..
©-Adjusting the backrest angle : press the
button forward/back¢ ,&..
©-Raising/lowering* the head restraints:
press the button up/down¢,&. .
@ -Lengthening/shortening the upper thigh
support* :
lift the handle. A spring moves the
front seat cushion forward ¢
.&..
A WARNING ,--
- Never adjust the driver's or front pas
senger's seat while the vehicle is moving.
If you do this while the veh icle is moving,
you will be out of position. Always adjust
the dr iver's or front passenger's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
he ight. Check to see that no one is in the
way, or ser ious injury could result!
- Because the seats can be electrically ad
justed with the ignition off or with the
ignit ion key removed, never leave chil
dren unattended in the vehicle. Unsuper
vised use of the electric seat adjust
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas
sengers must never ride in a moving ve
hicle with the backrest reclined. Safety
belts and the airbag system only offer
maximum protection when the backrest
is upr ight and the safety belts are prop
erly positioned on the body. The more
the backrest is reclined, the greater the
risk of persona l injury from an incorrect
seating position and improperly posi
tioned safety belts.
Page 66 of 286

64 Seats and storage
Seat memory
Description
Applies to vehicles: with memory function
The memory function allows you to quickly
and easily sto re and recal l personal seating
p rofiles for the dr iver. The memo ry func tion is
operated through the master key and the
memory buttons in the driver's door .
The driver's seating profi le is stored and as
sig ned to the master key each t ime the vehi cle
is locked . When you open the door, the seat
profile is automatically recalled. If two people
use one vehicle, it is recommended that each
person always uses "their own" master key.
Up to 2 seat profiles can be stored in the
memory buttons in the driver's door . Once
they are stored, these seat profiles can be se
lected at any time.
I n addition to the driver 's seat settings , you
can also store and access the exterior mirror
adj ustment settings* using the remote con
trol key or memory button.
Remote control key
App lies to vehicles: with seat memory
To assign the driver's seat settings to the re
mote contro l key when locking the vehicle, the
function must be activated in the radio or
MMI*
~ Se lect : ICAR I function button> Seat adj ust
ment
> D river's s eat > Remote co ntrol key >
on. Or
~ Select : ~I C,....A~R~ I fu nct ion but ton > Car sys tem s*
control button > Vehi cle setting s > Seat s>
Driv er' s seat > Remo te cont rol ke y> On .
(D Tips
If you do not want another d river's set
tings to be assigne d to the remote key,
sw itch off the memory function u sing the
rad io or MMI* or the
!ON/O FF I button
r=)poge 64.
Memory buttons
Applies to vehicles: with seat memory
Fig . 73 Driver's door: memo ry function buttons
The memory b uttons are located in the driv
er's door.
Switching the memo ry function on /off
~ Press the ION/OFF ! button to sw itch the
memory fu nction on/off . The word
OFF
lights up when the memory function is
sw itched off. Seat profiles are neither stored
nor recalled.
Storing a seat p rofile
~ Press the ISETI button. When the word SE T
lights up, the memory is ready to store set
tings.
~ Press a memory button dII or [Ii ) briefly . A
tone conf irms that the settings were stored.
Accessing a seat profile
~ If the driver's door is open and the ignition
is switched off, press the memory button.
~ If the driver's door is closed or the ignition is
sw itched on, press and hold the memory
button until the seat adjustment is com
plete .
_&. WARNING
-For safety reasons ., the seat setting can
only be re called when the vehicle is s ta
tionary - otherwise yo u risk hav ing an ac
cident.
- I n an emerge ncy the recall p roced ure ca n
be cancelled by pressing t he
ION/OFF !
switch or by ta pping the memo ry but
tons .
Page 68 of 286

66 Seats and st o rage
(upholder
Fig. 76 Ce nter conso le : front cupholder
Fig . 77 (upho lde r* in th e rear
F ront be verage hold ers
• You can accommodate two beverages in this
storage ¢
fig. 76.
A m aximum of two beverages can be placed in
the rear beverage holders*.
~ WARNING
Spilled hot liquid can cause an accident
and personal injury.
-
- Never carry any beverage containers with
hot liquids, such as hot coffee or hot tea,
in the vehicle while it is mov ing. In case
of an accident, sudden brak ing or other
vehicle movement, hot liqu id could spill,
causing scald ing burns . Sp illed hot liqu id
can also cause an accident and personal
injury .
- Use only soft cups in the cupholder . Hard
cups and g lasses can cause in ju ry in an
acc ident.
- Never use the cupholde r or adapter as an
ashtray - risk of fire.
(D Note
Only drink containers with lids should be
carried in the cupholder. Liquid could spill
out and damage your vehicle's electronic
equipment or stain the upholstery, etc.
Glove compartment
T he glove compartment is illuminated and
can be locked.
F ig. 78 G love co mpartme nt
• To open the g love compartment, pull the
handle i n the direction of the arrow ¢
fig. 78
and sw ing the cover down to open.
.. To close the g love compa rtment, push the
g love compartment lid upward until the lock
engages .
T he glove compartment ca n be locked using
the mechanical key
r::!) page 33.
On the right s ide in the glove compartment is
a ho lder with the key body into w hich the
emergency key must be clipped to be able to
start the veh icle.
WARNING
To reduce the risk of pe rsonal in jury in an
accident or sudden stop, always keep the
g love compartment closed while driving.
Page 71 of 286

Warm and cold Climate controls
Description
Th e climate control sy stem warms, cools and
adds humidity to the a ir in the veh icle inter io r.
It is the most effect ive when the windows and
power top are closed. If there is a build-up of
h eat inside the vehicle, ventilation can help to
speed up the cooling process .
I n all he ating mode f unctions except
defrost,
the blower on ly switches to a higher speed
once the engine coolant has reached a certain
temp erature.
Condensat ion from the cooling sys tem can
d rip and form a puddle of water under the ve
h icle. This is normal and does not mean there
is a leak .
Pollutant filter
The po llutant filte r removes po llutants s uch
as dus t and pollen from the air.
The air pollutants filte r must be changed at
the intervals spec ified in you r Wa rra nty
&
M aintenance book let, so tha t the air condi
tioner can prope rly work .
If you drive your vehicle in an area w ith h igh
a ir po llution , the fi lter may need to be
changed more frequent ly than specified in
your Aud i Warranty
& Ma intenance bookle t. If
in doubt, ask your authorized A udi Service Ad
v isor for advice .
Key coded settings
The clima te control sett ings are automat ically
stored and assigned to the remote co ntro l key
that is in use. These set tings are differe nt
when the power top is open or closed .
& WARNING
Reduced visibility is dangero us and can
cause accidents . -
Warm and cold 69
-For safe driving it is very important that
all windows be free of ice, snow and con
densat ion.
- Comp letely fam iliarize yourse lf with the
proper use and funct ion of the heat ing
and ve nti lation system and especially
how to defog and defrost the w indows.
- Never use the windshield wiper/washer
system in freez ing weather unt il you
have warmed the w indshield first, using
the heating and ventilation system. The
washer sol ution may free ze o n the wind
shie ld an d red uce visib ility.
(D Note
- If you s uspect that the air conditioner
has been damaged, switch the system
off to avoid furt her damage and have it
i n spected by a q ua lified dea lership.
- Repairs to the Audi air condition er re
quire specia l techni cal know ledge and
speci al tools. Contact an autho rized Aud i
dealer fo r ass istance.
@ For the sake of the environment
B y reduci ng the amou nt of f uel you use,
you also re duce the amount of pollu tan ts
emitted in to the a ir .
(D Tips
- Keep the air intake s lo ts ( in fro nt of the
w indshield) free from ice, snow and de
br is in order to maintai n the proper f unc
tion of the climate control system.
- T he energy m anagement system may
switch the seat heating* or rear window
defroster off temporar ily . These systems
are available again as soon as the energy
balance has been restored .
- Air escapes through vents under the rear
window. When placing items of clothing
on the luggage compartment cover, en
sure that the openings are not covered.