brake AUDI A5 CABRIOLET 2014 Repair Manual

236 Tire s and whee ls
- All four wheels must be fitted with radia l
t ires of th e same ty pe, size (r olling c ir­
cumfe rence) and the same tread pattern.
Dr iv in g with different tires reduces veh i­
cle handling and can lead to a loss of
c o ntrol.
- If the spare tire is not the same as the
t ires that are mounted on the veh icle -
for example with winter tires - on ly use
the spare tire for a short period of time
and dr ive with extra care. Refit the no r­
ma l road whee l as soon as safely possi ­
ble.
- Never drive faster than the maxim um
speed for which the tires on your vehicle
are rated because tires that are driven
faster than their rated speed can fail
sudden ly.
- Overloading ti res cause heat build-up,
sudden tire failure, including a blowout
and sudden deflation and loss of control.
- Temperature grades app ly to tires that
are properly inflated and not over or un­
derinflated.
- For technical reasons it is not a lways
poss ible to use wheels from other
vehicles -in some cases not even wheels
from the same vehicle model.
- If you install wheel tr im discs on the ve­
hicle whee ls, make sure that the air flow
to the brakes is not blocked . Reduced air­
flow to the brakes can them to overheat,
increasing stopping d istances and caus­
ing a collision.
- Run flat t ires may on ly be used on
vehicles that we re eq uipped w ith them
at the factory. The vehicle must have a
chassis des igned for r un flat t ires and a
factory-installed tire press ure monito r­
ing system * that indicates a loss of tire
pressure. Incorrect use of run flat tires
can lead to vehicle damage or accidents.
Check with an authorized Audi dea ler or
t ire spec ialist to see if you r vehicle can be
equipped with run flat tires .
If run flat
t ires a re used, they must be insta lled on
all four wheels. M ixing tire types is not
permitted.
(D Note
- For technical reasons, it is not generally
poss ible to use the wheel rims from oth­
er veh icles. T his can hold tr ue for wheels
of the same vehicle type.
- If the spare tire is different from the tires that you have mounted on your ve­
hicle (for example winter tires or wide
profi le tires), then use the spare tire for a
short period of time only and drive w ith
extra care. Replace the flat tire w it h the
ti re mat ching the othe rs on your vehicle
as soon as possi ble.
- Never d rive without the valve stem cap.
The v alves co uld get damaged.
@ For the sake of the environment
Dispose of o ld tires in accordance w ith the
l ocal requirements.
Uniform tire quality grading
- Tread wear
- Tra ction AA A B (
- Temperature ABC
Quality grades can be found where applicable
on the t ire s ide wall between tread shoulder
and maximum section width
c> page 233,
fig . 186.
For e xample: Tread wear 200 , Traction AA ,
Temperature A .
All passenger car ti res must conform to Feder­
al Safety Requirements in add ition to these
grades .
Tread w ear
The tread wear g rade is a comparative rating
based on the wear rate of the tire when tested
u nder contro lled conditions on a specified
government test course.
F o r example, a tire graded 1S0 wo uld wear
one and one ha lf (11/2) times as well on the
government course as a ti re graded 100. ..,_

driving a few yards and correct if neces­
sary . Follow the instructions from the
snow cha in manufacturer when doing so.
(D Tips
Where snow chains are mandatory oncer ­
tain roads, this norma lly also applies to
veh icles with all wheel drive .
Wheel bolts
Wheel bolts must always be tightened to the
correct torque.
The design o f whee l bolts is matched to the
factory insta lled r ims . If different rims are fit ­
ted, the correct wheel bo lts wit h the right
l ength and correctly shaped bolt heads must
be used. This ensures that wheels are f itted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bo lts from a different vehicle -even if it
is the same model<=>
page 266.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose caus ing loss of
cont ro l, a co llision and serious persona l in­
Jury .
- Always keep the w heel bolts and the
threads in the wheel hubs clea n so the
w hee l bolts can t urn easily and be p rop­
erly t igh tened.
- Never grease or oil the wheel bolts and
the threads in the wheel h ubs. They can
become loose wh ile d riving if greased or
oiled, even if tightened to the specified
torq ue.
- Only use whee l bo lts that belong to the
rim being installed .
- Never use different whee ls bolts on your
vehicle.
- Alw ays m ain ta in the co rrec t tig hten ing
torq ue fo r the wheel bo lts to reduce the
risk of a wheel loss . If the tightening tor­
que of the wheel bo lts is too low, they
can loosen and come out when the vehi-
Tire s an d wheel s 239
cle is mov ing. If the tightening torq ue is
too high, the wheel bolts and threads
can be damaged and the whee l can be­
come loose.
@ Note
The specified torque for the whee l bolts is
90 ft lbs . (120 Nm) w ith a tolerance of
± 7,4 ft lbs. (± 10 Nm). Torque whee l bolts
diagonally . After changi ng a wheel, the
torque m ust be checked as soon as poss i­
ble with a to rque wrench -preferably by an
a uthorized Aud i dea le r or qualified wor k­
shop .
Low aspect ratio tires
Your A udi is fac tory -eq uipped w ith low aspect
ratio tires . These tires have been tho ro ughly
tested and been se lected specifically for your
model for their superb performance, road fee l
and handling under a variety of driving condi­
tions . Ask your authorized Aud i dealer for
more details .
The low aspect ratio of these t ires is ind icated
by a numeral of
55 or less in the tire's size
designation. The numera l represents the ratio
of the tire's sidewa ll height in relation to its
tread width exp ressed in percentage. Conven­
tiona l tires have a he ight/w idth ratio of 60 or
more.
The performance of low-a spect-r atio tire s is
particularly sensit ive to improper inflation
pre ssure. It is therefor e important that low
a spect ratio tire s are inflated to the specified
pres sure and that th e inflation pr essure i s
regularly checked and maintained. Tire pre s­
sure s should be chec ked at lea st once a
month and always before a long trip
<=> page 228 , Checking tire pressure.
What you can do to avo id tire and rim
damage
Low aspect ratio tires can be damaged mo re
easily by impact w ith potholes, curbs, gull ies
or ridges on the road, particularly if the tire is
under inflated . ..,.
•
•

24 4 What do I do no w?
There are some restrictions on the use of the
compact spare tire. The compact spare tire
has been des igned specifically for your type of
vehicle.
It must not be swapped with a com­
pact spare tire from another type of vehicle.
Sno w cha in s
For technical reasons, the use of snow chains
on the compact spare tire is
n ot permitted .
If you do have to dr ive with snow cha ins and a
front tire fails, mount the spare wheel w ith
tire instead of a rear tire. Install the snow
chains on the rear tire and use it to rep lace
the defective front tire.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the spare tire is more than 6 years o ld,
use it only in an emergency and w ith ex­
t reme caution and careful driving.
- The spare tire is intended only for tem­
porary and short-term use. It should be
replaced as soon as possib le w ith the
normal wheel and t ire.
- After mounting the compact spare tire, the tire pressu re must be checked as
soon as poss ible. The tire pressure of the
c ompac t spare tire must be 4.2 bar; oth­
erwise, you risk hav ing an accident.
- Do not drive faster than 50 mph (80 km/
h). You risk having an acc ident.
- Avoid full-throttle acce le rat ion, heavy
braking, and fast corner ing . Yo u risk hav­
ing an acc iden t.
- Never drive us ing more than one spare
wheel and tire. You risk having an acci­
dent.
- No rma l summer or winte r tires m ust not
be mounted on the compact spare whee l
rim.
- F or te chni cal reasons, the use of ti re
chains on the spare tire is not permitte d.
If it is necessary to drive with tire chains,
the spare whee l must be mounted on the
front axle in the event o f a f lat in a rear tire. The new
ly available front wheel
must then be installed in place of the
rear whee l with the flat tire. Installing
the t ire cha in before mounting the whee l
and tire is recommended .
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard brak ing or in an accident.
Never store the spa re tire or jack and
too ls in the passenger compa rtment.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
"'After you expe rience a tire failure, pull the
car we ll away from moving traffic and try to
reach
le vel ground before you stop ¢ ,&.
"'All passengers should leave the car and
move to a safe location (for instance, behind
the guardrail)¢ &,.
"' Engage the
parking brake to p revent your
veh icle from rolling unintentionally¢&, .
"' Move the
selec tor lever to the P positi on.
"'I f you are towing a t railer : unhitch t he trai l­
er from you r vehicle.
"' Take the
jack ¢ page 243 and the spare tire
¢ page 243 out of the luggage compart­
ment .
A WARNING
=
You or your passengers could be injured
while changing a wheel if you do not fo l­
l ow these safety precaut ions :
- If you have a flat tire, move a safe dis­
tance off the road . Turn off the engine ,
turn the eme rgency flashers on and use
other warning devices to a le rt other mo­
torists.
- Make sure that passengers wait in a safe
place away from th e vehicle and well
away from the road and traffi c.
- To help prevent the vehicle from moving
-
suddenly a nd possib ly slipping off the ..,_

jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed with the fold­
ing chocks o r other objects. When one
front wheel is lifted off the ground, plac­
ing the Automat ic Transm iss ion in "P"
(Park) wi ll
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a st urdy board under the jack.
- Always store the vehicle tool kit, the
jack* and the repla ced ti re in the l uggage
compartment
¢ page 12 7.
(D Note
If you are chang ing the wheel on a steep
incline, use a rock or similar object to
block the opposite wheel to prevent the
ve hicl e from mov ing.
(l) Tips
Obey a ll laws.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly tha t order .
1. Remove the dec orative whe el co ver* or
the
wh eel b olt cap s* . Fo r mor e details see
a lso
¢ page 245, Decorative wheel cov­
ers
or¢ page 246, Wheels with wheel
bolt caps.
2 . Loosen the wheel bo lts ¢ page 246.
3. Locate the proper mounting po int for the
jack and align the jack below that point
c::> page247.
4. Lift the car with the jack c::> page 247 .
5. Remove the wheel with th e flat tire and
then install the
s pare tir e c::> page 248 .
6. Tighten all wh eel bo lts light ly .
7.
Low er the ve hicle wit h the ja ck.
8. Use the wheel bolt wrenc h and
firmly
tighten a ll whee l bolts in a cr isscross pa t­
tern ¢
page 246.
What do I do now ? 245
9. Replace the decorative wheel co ver* or
the
wheel bolt caps*.
A WARNING
Always read and fo llow all WARNINGS and
i n format ion
c::> .&. in Raising the vehicle on
page 247
and c::> page 249.
After changing a wheel
A wheel change is not complete without the
doing the following.
.,. Always store the vehicle tool kit, the jack*,
and the replaced tire in the luggage com­
partment
c::> page 12 7 .
.,. Check the tire pressu re of the spare tire as
soon as possible .
.,. As soon as poss ib le, have the
t ightening
torqu es
on all wheel bolts checked with a
t orque wrench. The co rrect tighte ning tor­
que is
90 ft lbs. (120 Nm).
.,. Have the fla t tire
repl ace d as soon as possi­
b le.
(D Tips
- If you not ice tha t the wheel bo lts a re
c orroded and difficult to turn while
chang ing a tire, they shou ld be replaced
before you c heck the tightening torque.
- Drive at reduced speed until you have the tightening torques checked .
Decorative wheel covers
Applies to vehicles: wit h deco rat ive w hee l covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 19 0 C ha ngi ng a w heel : re moving the w hee l cove r ...

down on the end of the wheel bolt
wrench with
one foot only. As you do so,
ho ld on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be li~ed with the jock first
before the wheel can be removed.
*
Fi g. 193 Sill panels: markings
Fig. 194 S ill: posit ion ing the vehicle jack
The location of the jack point is indicated by
an indentat io n on the unders ide of the vehicle
¢fig . 193 .
.,. Activate the park in g brake to prevent the
vehicle from rolling u nintentionally.
.,. Move the selecto r lever to position P.
.,. Find the
mark ing ( impr int) on the si ll that is
nearest the wheel that w ill be changed
¢fig. 193. Behind the ma rking, there is a
li ft ing p oint on the s ill for the vehicle jac k.
.,. Turn the
vehicle jack located unde r the lift­
ing point on the si ll to raise the jack until
the jaw
¢ fig . 194 @ covers the notch on
the vehicle¢
,&.¢CI) .
.,. Align the vehicle jack so the jaw @covers
the notch and the base p late @ is flat on
t h e f loor. The base plate @ must be
vertical
under the lifting point @.
What do I do now ? 24 7
.,. Insta ll the rod on the vehicle jack: Insert the
rod into the opening on the handwheel. T urn
the rod left or r ight to secure it.
.,. Continue raising the jack w ith the rod unt il
the wheel lifts off the ground slightly.
Position the vehicle jack
only under the desig­
nated lifting points on the si ll
¢fig. 193.
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other
location
r::;, & r::;,(D.
Soft g round u nder the jack can cause the ve­
hicle to slip off the jack. Always place the jack
o n firm ground. Use a flat, stab le support if
necessary . Use a non-slip surface such as a
rubber mat on a
slippery surface such as tile .
.&_ WARNING
- You or your passengers co uld be inju red
while changing a wheel if you do no t fo l­
low these sa fety p reca utions:
- Position the vehicle jack only at the designated lifting points and align the
jack. Otherwise, the vehicle jack could sli p and cause an injury if it does not
have sufficient hold on the vehicle.
-A soft or unstable surface under the jack may cause the veh icle to slip off
the jack. Always p rov ide a fi rm base for
t h e jack on the ground. If ne cessary,
u se a st urdy board under the j ack.
- On hard, slippery su rface (such as t iles)
u se a rubber mat or simi lar to p revent
the jack from sl ipping .
- To help prevent injury to yo urself and
your p assengers:
- Do not ra ise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up .
- Make sure that passengers wait in a
safe p lace away from the veh icle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then cont inue to
raise the jack.

248 What do I do now?
(D Note
Do not lift the vehicle by the sil l. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step -by -step for
changing the wheel .
Fig. 195 Chang ing a w hee l: u sing t he screwdriver han ­
dle (with the blade removed) to turn th e bo lts
Fig . 196 Chan ging a w hee l: al ig nm en t pi n inside the
top hole
After you have loosened a ll wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Remove the topmost wheel bolt completely
with the
hexagonal socket in the screwdr iv­
er hand le (vehicle tool kit)
c::>fig. 195 and
set it aside on a
clean surface.
.. Screw the threaded end of the
alignment
pin
from the tool kit hand -tight into the
empty bolt hole
c::> fig . 196.
.. Then remove the other wheel bo lts as de­
scribed above. ..
Take off the wheel leaving the alignment pin
in the bolt hole
c::> (D.
Putting on the spare tire
.. Push the spare tire over the alignment pin.
.. Screw on the wheel bolts and tighten them
slightly using the hexagonal socket .
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest.
.. Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.. Use the wheel bolt wrench to tighten all
wheel bo lts firm ly
c::> page 246 . Tighten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
.. Perform the steps required after changing
the wheel
c::> page 245, After changing a
wheel.
The hexagonal socket makes it easier to re­
move the wheel bolts from the rim. Care
should be taken when removing the reversible
blade .
(D Note
When removing or installing the wheel,
the rim cou ld hit the brake rotor and dam­
age the rotor. Work carefu lly and have a
second person to help you.
(@ Tips
- When mounting tires with
unidirectional
tread design
make sure the tread pat­
tern is po inted the right way
c::> page 249.
- The wheel bolts should be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the wheel.
- Do not use the hexagonal socket in the
screwdriver handle to loosen or t ighten
the whee l bolts .

Fuses and bulb s 251
No. Con sumer Amps No. Consumer Amps
•
A/C system pressure sensor, Two-door models: rear left
• electromechanical parking window regulator; Four-
brake, Homelink, automatic 11 door models:
rear left door
30
3 dimming interior rear view
5 (window regulator, central
m irror, air quality/outside locking, switch, lighting)
air sensor, Electronic Stab ili-
12 Rain and light sensor
5
zation Control (button)
5 Sound
actuator
5
Fuse panel© (r e d )
6 Headlight
range cont rol/
5/7,5
head light (cornering light)
No. Consumer Amps
3 Lumbar support 10
7 Headlight (corner
ing light) 7,5
4 Dynamic steering 35
Contro l modu les (e lectro-
s Inter ior lighting (Cabriolet)
5
8 mechanical parking brake,
5
shock absorber, quattro
sport), DCDC converter
9 Adaptive cru ise contro l 5 6
W
indshield washer system,
35
h eadlight washe r system
7 Vehicle electrical
system
20
control module 1
10 Shift gate/clutch
sensor
5
1 1 Side ass ist 5
8
Vehicle electr ica l system
30
control module 1
1 2 Headlight range
control,
5
park ing system 9 Left rear window regulator
7,5/20
motor (Cabriolet)/sunroof
13 Airbag 5
14 Rear wiper (allroad) 15 10 Vehicle e
lectrical system
30
control module 1
1 5 Auxi
liary fuse (instrument
10
pane l) 11 R
ight rea r window regulato r
7,5/20
(Cabriolet)/sun shade motor
16 Aux
iliary fuse terminal 15
40
(engine area) 12 Anti-theft
alarm warning
5
system
Fuse p anel @ (brown )
No. Con sumer Amps
2 Brake light sensor 5
3 Fuel
pump
25
4 Clutc h sensor 5
5 Left
seat heating with/w ith-
15/30
out seat vent ilation
6 Electronic Stab
il iz at ion Con-
5
tro l (e lectric)
7 Horn 15
Front left door (window reg-
8 ulator, centra
l locking, mir-
30
ror, switch, lighting)
9 Winds hield wipe r motor 30
1 0 Electronic
Stabilizat ion Con-
25
trol (valves)

No. Consumer
5 Electromechanical
parking
brake
6 Electronic damping control
7
Electromechanical parking
brake
8 Rear exterior lighting
9 quattro sport
10 Rear
exterior lighting
1 1 Central locking
12 Termina
l 30
Fu se pa nel © (brown )
No. Con sumer
1 Luggage compartment lid
control module (allroad)
2 1
2-volt socket, cigarette
lighter
3 DCDC
converter path 1
4 DCDC converter path 2,
so und amplifier, radio
6
Right upper cabin heat ing
(Cabr iolet)
7
Electromechanical parking
brake
Right front door (w indow
9 regu lator, central lock ing,
m irror, swit ch, lig hting)
10 Left upper
cabin heating
(Cabriolet)
Two -door models: rear right
window regulator; Four-
11 door mode
ls: rear right door
(window regulator, central
locking, sw itch, lighting)
12 Cell phone prep
Fu se panel © (black )
No. Consumer
1 Right front seat heating
4
MMI
5 Radio
6 Rear view camera
Amp s
5
15
30
30
35
30
20 5
Amp s
30
20
40
30
30
30
30
30
30
5
Amps
15
7,5
5
5
Fu ses and bulb s 253
No. Consumer Amps
7
Rear window heater (all-
30
road)
8 Rear Seat Entertainment 5
Bulbs
Replacing bulbs
For your safety, we recommend that you hove
your authorized Audi dealer replace any bulbs
for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb. This applies especially to the light bulbs
in the front of your car which you can only
reach through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause serious cuts, parts must
be correct ly take n apa rt and then p roperly put
bac k together to he lp p revent breakage of
parts and long te rm damage from water that
can enter housings that have not been p roper­
ly re sea led .
Fo r you r safety, we re commend that you have
your autho rized Audi de aler replace any b ulbs
f or you, since your dealer has the proper too ls,
the correct bulbs and the expertise.
Gas disc har ge la mp s (Xenon l ig hts)*:
Due to the high electr ical voltage, have the
bulbs replaced by a qualified techn ic ian .
Head lights w ith Xenon light are identified by
the h igh vol tage sticker.
_&. WARNING
Changing Xenon lamps without the neces­
sary equipment can cause serious persona l
injury .
- Bulbs are pressurized and can explode
when being changed. Potential risk of in­
jury!
-
•
•

256 Emergency situations
@ Tips
The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative post
because the batte ry manager system must
be able to detect the battery 's state of
charge. Always connect the negative
ground cab le to the negative ground post
of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
Fig. 201 Engine compartment: Connectors fo r jum per
cables and charger
Fig. 202 Jump sta rting wi th the battery of anot her ve ·
h ide :@ booster battery, @ disc harged vehicle battery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your vehicle .
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake .
Connect POSITIVE(+) to POSITIVE(+)
(red)
.. Remove the cover above the jump start con­
nection .
.. Open the cover on the positive pole
¢fig. 201.
1. Connect one end of the red positive cable
on the
jump start bolt c::> fig. 202 @
(Bolts under cover= "positive") of the ve­
hicle to be started @.
2. Connect the other end to the positive ter-
minal @of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the b lack negative ca­
ble to the negative terminal @of the
booster battery @.
4. Connect the other end to the
jump start
bolt @
(Bolts with hex head= "negative")
of the vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the
booster battery@. Run the engine at a
moderate speed.
.. Start engine with discharged vehicle battery
@ in the usual manner .
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds .
Wait for about 30 seconds and then try
again .
.. With eng ine running, remove jumper cables
from both vehicles in the exact
reverse or­
der .
.. Close the cover on the positive pole .
T he battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect­
ed with their
metal parts in full contact with
the battery terminals.
A WARNING
--
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable manufac-
turer . If in doubt, call for road service . ..,.

26 6 Con sum er Inf ormation
-Always make sure the transmission se­
lector lever (automatic transmiss ion) is
in "P" (Park position) and the park brake
is f irmly app lied .
@) For the sake of the environment
-Changing the engine settings wi ll ad­
versely affect em iss ion levels. This is det­
rimental to the environment and increas­
es fuel consumption .
- Always observe env ironmental regula­
tions when dispos ing of old engine oil,
used brake fluid, dirty engine coolant,
spent batteries or worn out tires.
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo ­
rate Material -spec ial handling may ap­
ply, see www.dtsc.ca .gov/hazardous­
waste/perch lorate . When the veh icle or
parts of the restraint system including
airbag modules safety belts wit h preten ­
sioners are scrapped, all applicable laws
and regulations must be observed. Your
authori zed Aud i dea ler is familiar with
these requirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories.
Your veh icle incorporates the latest safety de­
sig n featu res ensu ring a high standard of ac­
tive and passive safety .
This safety could be compromised by non-ap­ proved changes to the veh icle. For this reason ,
if pa rts have to be replaced , please observe
the following points when install ing addition­
a l accessories: Approved Audi accessories and genuine Aud
i
parts are available from authorized A udi deal­
er.
T hese dea le rs a lso have the necessary facili­
ties, tools and trained specialists to install the parts and acc essories proper ly .
A WARNING
-Using the wrong spare parts or using non-
approved accessories can cause damage to
the veh icle and ser ious persona l injury.
- Use on ly accessories express ly approved
by Audi and gen uine Audi spare parts
- These parts and accessories have been
specia lly designed to be used on yo ur ve­
h icle .
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on a ir­
bag covers or within the airbag deploy­
ment zones . Do ing so will increase the
risk of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNI NGS
9 page 206 .
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not
performed accord ing to specified meth­
ods, this c an resu lt in seve re damage to
your vehicle's eng ine and body (such as
corrosion) and adversely affect yo ur vehi ­
cle's warranty .
- If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized A udi dealer as soon as
possible .
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipu lations.