bolt pattern AUDI A5 CABRIOLET 2015 Owners Manual

Wheels
A WARNING
Wheel bolts that are tightened or repaired in­correctly can become loose and result in loss
of vehicle control , which increases the risk of
an accident. For the correct tightening specifi­
cation, refer to
c:> page 231, After changing a
wheel.
- Always keep the wheel bolts and the threads
in the wheel hub clean and free of grease.
- Only use wheel bolts that fit the rim .
- Always have damaged rims repaired by an
authorized Audi dealer or authorized repair
facility. Never repair or disassemble rims
yourself, because this increases the risk of an accident.
Winter tires
Winter tires significantly improve the vehicle's handling when driving in winter conditions . Be­
cause of their construction (width, compound,
tread pattern), summer tires provide less traction
on ice and snow.
.., Use winter tires on all four wheels .
.., Only use winter tires that are approved for your
vehicle.
.., Please note that the maximum permitted
speed may be lower with winter tires
c:> .&,.
Your authorized Audi dealer or authorized re­
pai r facility can inform you about the maximum
permitted speed for your tires .
.., Check the tire pressure after installing wheels
c:> page 219.
The effectiveness of winter tires is reduced great­
ly when the tread is worn down to a depth of
0 .1S7 inch (4 mm). The characteristics of winter
tires also decrease greatly as the tire ages, re ­
gardless of the remaining tread.
A WARNING
-Never drive faster than the maximum per­
mitted speed for your t ires. This could cause
the tires to heat up too much . This increases
the risk of an accident because it can cause
the tire to burst.
224
- Always adapt your driving to the road and
traffic conditions. Drive carefully and reduce
your speed on icy or slippery roads. Even
winter tires can lose traction on black ice.
@ For the sake of the environment
Reinstall summer tires at the appropriate
time, because they provide better handling
when roads are free of snow and ice. Summer
tires cause less road noise, tire wear and fuel
consumpt ion.
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only win­
ter tires w ith the
& symbol may be permit­
ted.
· Snow chains
Snow chains improve traction in the snow .
.., Only install snow chains on the front wheels.
This applies also to vehicles with all wheel drive* .
.., Check and correct the seating of the snow
chains if necessary after driving a few feet. Fol­
low the instructions from the manufacturer .
.., Note the maximum permitted speed when driv­
ing with snow chains . Do not exceed 30 mph
(SO km/h) .
Snow chains not only improve the
driving in win­
ter road conditions, but also the
braking.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author­
ized repair facility to see if you may use snow
chains .
Use
fine-mesh snow chains. They must not add
more than 0.53 inch (13.S mm) in height, includ­
ing the chain lock.
You must remove the chains when driving on
roads that are
free of snow. When roads are free
of snow, snow chains can impair handling and .,.

M N
ci LL co
rl I.O
"' N
"' rl
off the ground, placing the Automatic Trans­
mission in "P" (Park) will
not prevent the ve ­
hicle from moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment ¢
page 118 .
(D Note
If you are chang ing the wheel on a steep in­
cline, use a rock or sim ilar ob ject to block the
opposite whee l to prevent the vehicle from
mov ing.
(D Tips
Obey a ll laws.
Changing a wheel
When you change o whe el, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the decorative wheel cover* or the
wheel bolt caps* . For more details see a lso
¢ page 231, Decorative wheel covers or
¢ page 232, Wheels with wheel bolt caps.
2 . Loosen the wheel bolts¢ page 232 .
3. Locate the proper mount ing po int for the
jack and align the jack below that point
¢page 233.
4. Lift the car wit h the jack ¢ page 233.
5. Remove the wheel with the flat tire and then
install the
spare tire¢ page 234.
6. Tighten all wheel bolts light ly .
7.
Lower the vehicle w ith the jack.
8 . Use the wheel bolt wrenc h and
firmly tighten
all wheel bolts in a crisscross pattern
c> page232 .
9. Replace the decorative wheel cover* or the
wheel bolt cap s* .
.&, WARNING
Always read and follow all WARNINGS and in­
formation
¢ .&. in Raising the vehicle on
page 233
and ¢ page 235.
Emergen cy assistance
After changing a wheel
A wheel change is not complete without the do­
ing the following .
"Always store the vehicle tool kit, the jack", and
the replaced t ire in the luggage compartment
¢page 118.
"Check the tire pressure of the spare tire as soon
as poss ible.
" As soon as possible, have the
tightening tor ­
ques
on all wheel bolts checked with a torque
w rench. The cor rect tightening torque is 90
ft
lbs. (120 Nm).
" Have the flat tire
replaced as soon as possible.
(D Tips
-If you notice that the wheel bolts are cor­
roded and difficult to turn while changing a
tire, they should be replaced before you
check the tightening torque .
- Dr ive at reduced speed until you have the
tightening torques checked.
Decorative wheel covers
Applies to vehicles : wit h decorative w hee l covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig . 186 C ha ng in g a w heel: removing the wheel cover
Removing
" Insert the hook provided with the vehicle tool
kit in the hole in the hub .
" Pull off the
decorative wheel cover¢ fig. 186 .
231

Emergency assistance
points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step-by-step for chang ­
ing the wheel .
Fig. 191 Cha ngin g a w hee l: u sing t he screwd rive r hand le
(w ith t he blade re moved) to turn the bo lts
Fig. 192 C han gin g a w heel: align men t pin inside the top
h ole
After you have loosened all wheel bolts and
ra ised the veh icle off the ground, remove and re­
p la ce the whee l as follows:
Removing the wheel
"' Remove the topmost wheel bolt completely
with the
hexagonal socket in the screwdriver
handle (vehicle tool kit)
r=;, fig. 191 and set it
aside on a
clean surface.
"' Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the empty bo lt
hole
r=;, fig . 192.
"' Then remove the other wheel bo lts as described
above.
"' Take off the wheel leaving the alignment pin in
the bolt hole
r=;,(I).
234
Putting on the spare tire
"'Push the spare tire over the alignment pin.
"' Screw on the wheel bolts and tighten them
slightly using the hexagona l socket .
"' Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest.
"' Turn the jack hand le counter-clockwise to lower
the vehicle until the jack is fully released .
"' Use the wheel bolt wrench to tighten all wheel
bolts firmly
r=;, page 232. Tighten them in a
crisscross pattern,
from one bolt to the (ap­
proximately) opposite one, to keep the wheel
centered.
"' Perform the steps required after changing the
wheel
r=;, page 231, A~er changing a wheel .
The hexagonal socket makes it easie r to remove
the wheel bolts from the rim. Care should be tak­
en when removing the reversib le blade .
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor and damage the
rotor. Work carefully and have a second per­
son to he lp you.
(D Tips
- When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
r=;, page 235.
- The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
- Do not use the hexagonal socket in the
screwdriver handle to loosen or tighten the
wheel bolts.

M N
ci u.. co ,...., \!) ..,.,
N ..,., ,....,
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right dir ection .
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spa re tire w ith a t read pa tte rn in­
t e nded fo r use in a specific d ir e ct ion, p lease no te
the following:
- The direction of rotation is marked by an
arrow
on the side of the tire .
-If the spare t ire has to be installed in the incor­
rect direction, use the spare tire only tempora­
rily since the tire will not be able to achieve i ts
o ptimum performanc e character istics wit h re­
gard to aquaplaning, noise and wea r.
- We recommend that you pay pa rticular atten­
t io n t o this fact du ring wet weat he r and t hat
yo u adju st yo ur sp eed to match road condi­
t ions.
- Re place the fla t tire w ith a new one and have i t
i nsta lled on yo ur vehicle as s oon as po ssible to
re store the han dling a dvan tages o f a un idirec­
t io na l tire.
Notes on wheel changing
P lease read the information ¢ page 216, New
tires or wheels
i f you are going to use a spare tire
which is different from the tires on your ve hicle.
Afte r you change a tire:
- Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as po s­
sible by your authorized Audi dealer or quali­
fied workshop .
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of 90
ft lbs. (120 Nm ).
- If you notice th at the wheel bolt s are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque .
Emergency assistance
-Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover .
Until then , drive with extra care and at reduced
speed s.
_& WARNING
- If you are going to e quip your ve hicl e wit h
tires o r rims which differ from those which
were factory installed, then be sure to read
the information
¢ page 216, New tires or
wheels.
- Always make sure the damaged wheel o r
even a flat tire a nd the jack a nd too l kit a re
p roperly secu red in the luggage compart­
men t and are not loos e in t he passeng er
compa rt m ent.
- In an acci dent or sudde n man euver they
could fly forwa rd, inj uring a nyone in t he ve­
h icle.
- Always s to re damag ed wh eel , jack and tools
s ecure ly in the luggage co mpart ment. Ot h­
e rwi se, in an accident o r sud den man euver
they co uld fly forward, causing injury to pas­
sen gers in t he ve hicle.
(D Note
D o not use co mmercially ava ilab le tire seal­
a nts. O therwise, the e le ct ric al c ompone nts of
the tire pre ssure monit oring sys tem * w ill no
l on ger wor k properly and t he sensor for the
tire pressu re monito ring system * wi ll have to
b e replaced by qu alified workshop.
-
235