service AUDI A6 1995 C5 / 2.G AEB Engine OBD and DTC

01-6

Function 03: Output Diagnostic Test Mode Ignition switched on
Function 04: Basic Setting Engine running at idle
Function 07: Code Control Module Ignition switched on
Function 08: Read Measuring Value Block Ignition switched on -or- Engine running at idle -or- Driving Modes under address word 33: Mode 1: Transfer diagnostic data Ignition switched on -or- Engine running at idle
Mode 2: Transfer operating conditions Ignition switched on -or- Engine running at idle
Mode 3: Check DTC memory Ignition switched on -or- Engine running at idle
Mode 4: Erase diagnosis information Ignition switched on -or- Engine running at idle
Mode 5: Output of HO2S signals Ignition switched on -or- Engine running at idle
Mode 6: Transfer measuring values Ignition switched on -or- Engine running at idle
Mode 7: Check DTC memory Ignition switched on -or- Engine running at idle Under Address word 33, Mode 1 to Mode 7 can be addressed.
Under Mode 1 individual measuring values can be displayed. Mode 1 is not recommended for use in an Audi Service
department, because these values can be displayed much more precisely using address word 01 and "Basic Setting"
function 04 or "Read Measuring Value Block" function 08.
Mode 2 shows the operating conditions under which the stored malfunctions were recognized.
With Mode 3, DTC memory is checked-with Mode 4, DTC memory is erased.
Pa
ge 10 of 57 On Board Dia
gnostic
(OBD
)
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.1

Mode 5 shows the statistical value of the oxygen sensors as mandated by law. As these values have no direct bearing on
oxygen sensor diagnosis, Mode 5 is of no particular value in an Audi Service department.
Under Mode 6, values can be checked for components and systems that are not continuously monitored.
With Mode 7 all malfunctions can be checked, even if they have not switched on the Malfunction Indicator Lamp (MIL) (if
the MIL has not been switched on, there is no malfunction recognized under Mode 3)
Pa
ge 11 of 57 On Board Dia
gnostic
(OBD
)
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.1

01-10

Notes:
If the ECM version that corresponds to the
vehicle is not displayed, replace ECM Page
01
-57
. Incorrect ECM coding leads to:

Performance problems (e.g. jerky shifting,
abrupt load changes, etc.
Increased fuel consumption
Elevated exhaust gas values
Reduction in transmission service life
Malfunctions not present are stored in DTC
memory
Necessary functions are not carried out (oxygen
sensor control, actuation of EVAP canister
system, etc.)

-
Press button to advance program
sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Continue as specified in procedures for specific OBD functions.
Pa
ge 16 of 57 On Board Dia
gnostic
(OBD
)
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.1

01-12

8D0907557 1,8L R4/5VT MOTR HS D02 Coding 06051
WSC 00000

Indicated on display (ECM identification and coding, e.g. 06051)
-
Press button to advance program sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
Note:
The Motronic ECM -J220- only uses the code that has been entered after
the ignition has been switched off once. Incorrect coding leads to: - Press buttons -0- and -6- to select "End Output" function 06, and press
-Q- button to confirm input.
Performance problems (e.g. jerky shifting, abrupt load changes, etc.Increased fuel consumptionElevated exhaust gas valuesFalse malfunctions stored in DTC memoryReduction in transmission service life
Pa
ge 19 of 57 On Board Dia
gnostic
(OBD
)
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.1