set AUDI A6 1995 C5 / 2.G AEB Engine Throttle Valve Control Module And Checking

24-100

Function

Idle speed stabilization is integrated in the
throttle valve control module -J338-. In the
housing opposite the throttle valve are Throttle
Position (TP) sensor -G69-, Closed Throttle
Position (CTP) switch -F60-, throttle drive -G186-
and angle sensor -1- for throttle drive -G187-.

The housing should not be opened.
The individual components cannot be replaced or
mechanically adjusted. All adjustments are
accomplished by the VAG 1551 Scan Tool (ST)
using the "Basic Setting" function 04.
If the complete throttle valve control module is
without power (i.e. disconnected), the throttle
valve assumes a mechanical closed throttle
position that results in an increased idle speed of
1200-1300 RPM (with engine at operating
temperature).
If only the Throttle Position (TP) actuator -V60- is
without power, the throttle valve also assumes a
mechanical closed throttle position (limp-home
position), but because the signal from the CTP
switch -F60- can still be recognized, a nearly
"normal" idle speed of approx. 900 RPM is
maintained with a corresponding reduction of the
ignition timing advance.
If the Engine Control Module (ECM) recognizes a
Pa
ge 2 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2

24-120

Test procedure

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on; engine not running) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -6- and -0- to input display group number 60, and
press -Q- button to confirm input.
System in Basic Setting 60 1 2 3 4

Indicated on display (1-4 display fields)
Note:
After confirming input of display group 60, adaptation is started. The
Throttle Position (TP)sensor is positioned in the closed throttle, wide
open throttle and limp-home positions. Following this procedure, other
intermediate steps will create a characteristic curve of the relationship
between Throttle Position (TP) sensor -G69- and angle sensor for
throttle drive -G187-. The Motronic ECM stores these values in permanent memory.
Afterward, the throttle valve assumes the starting position.
Pa
ge 35 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2

24-121

- Compare display with specified values (display
fields 1-4):

Display fields

1 2 3 4
Display group 60: Basic setting-throttle valve control module
Display
xxx
xxx
Idle
Part throt
Full throt
Decel
Enrich ADP runs
ADP. OK
ADP. ERROR
Indicates Throttle valve
angle Throttle drive
angle Operating
condition Adaptation condition
Range
0-90
--- ---
Specified
value 0-5 Idle ADP. runs

ADP. OK

(ADP. ERROR indicates unsuccessful
adaptation)

If displayed values are NOT OK:
- Check DTC memory ( Page 01
-15
)
Pa
ge 36 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2