ESP AUDI A6 1996 C5 / 2.G 01V Transmission Electrical Testing Workshop Manual

01-293

Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
21 A) 41 + 28
3)
41 + 34
41 + 55
41 + 26 Wiring to ECM (throttle
signal)
Ignition switched
off ECM
disconnected infinite
1)
- Check wiring per wiring
diagram.

41 + xx
2)

less than 1.5


1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Corresponding terminal assignment at Engine Control Module (ECM)

Electrical wiring diagrams Troubleshooting & Component Locations A) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-Bus

Pa
ge 32 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

2) Corresponding terminals at Engine Control Module (ECM).

Electrical Wiring Diagrams & Component Locations A) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-Bus

Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, engine and transmission allocation, ratios, equipment

Pa
ge 35 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-295

Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
23 A) 40 + 28
3)
40 + 34 Wiring to ECM (engine
RPM signal)
Ignition
switched off
- ECM
disconnected 15 - 80 K
- Check wiring per wiring diagram.
- Check on-board computer.

40 + xx
2)
less than 1.5

Repair Manual, Electrical
Equipment, Repair Group 01

24 A) 20 + 28
3)
20 + 34
20 + 55
20 + 26 Wiring to ECM (torque
reduction)
Ignition
switched off
- ECM
disconnected infinite
1)
- Check wiring per wiring diagram.

20 + xx
2)
less than 1.5


1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Corresponding terminal assignment at Engine Control Module (ECM).
Pa
ge 36 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-296

Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional steps Specified
value Corrective action
25 A) 51 + 28
3)
51 + 34
51 + 55
51 + 26 Wiring to ECM (upshift/downshift
signal)
Ignition switched
off
- ECM
disconnected infinite
1)
- Check wiring per wiring
diagram.

51 + xx
2)
less than 1.5


1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Corresponding terminal assignment at Engine Control Module (ECM).

Electrical Wiring Diagrams & Component Locations A) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-Bus

Pa
ge 38 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-302

Wiring between transmission and 88-pin
connector for Transmission Control
Module (TCM) -J217-, testing


Perform if:

Output Diagnostic Test Mode (DTM) or
Electrical test indicates malfunctions in the
transmission, the TCM -J217-, or in the
corresponding wiring.

Test conditions
Ignition switched off
Connect VAG1598/20 adapter only to 88-pin
connector of transmission wiring harness.
Perform measurements with VAG1598/20
adapter on the outside of the vehicle

- Remove noise insulation panel.
- Remove bracket -1- for noise insulation panel.
Pa
ge 48 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16