AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide A6 1996 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/953/w960_953-0.png AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide

Page 11 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-7
 
  
11 - 
Engine oil temperature sensor -G8- 
10 Nm (7 ft lb)
12 - 
Sealing washer If leaking, cut open and replace
13 - 
O-ring Always replaceSnap into grooves on oil cooler
14 - 
Oil cooler Re

Page 12 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-8
 
    
Fig. 1  Checking oil pump backlash
New: 0.05 mm (0.002 in.) Wear limit: 0.20 mm (0.008 in.)
    
Wear limit: 0.15 mm (0.006 in.)  Fig. 2  Checking oil pump axial clearance
Pa
ge 12 of 33 L

Page 13 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-9
      
Oil pan, removing and installing
 
     
Special tools and equipment  
     
10-222A engine support bridge with 10-222A/1 
bracket for engine 
     2024A engine sling
     3249 puller

Page 14 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-10
      
CAUTION! 
     
Before removing ribbed belt, note direction of 
rotation with chalk or felt-tip marker. 
Reversing the direction of rotation of a used 
belt can destroy the belt. 
    
-

Page 15 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-11
      
-  Remove side brace from left side of torque 
support bracket. 
    
Note:  
Illustration is shown with engine removed.  -  Remove torque support bracket from engine (arrows).
    
-  Cu

Page 16 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-12
 
    
-  Remove hose from turbocharger at air guide tube in lock carrier 
(arrow). 
    
-  Remove both nuts -1- from lower engine mount.
Pa
ge 16 of 33 Lubrication s
ystem com
ponents, removin

Page 17 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-13
      
-  Remove engine covers. 
    
-  Set 10-222A engine support bridge on fender mounting edges.
    
WARNING! 
Mounting hooks and pins on the engine sling must be secured with 
the position

Page 18 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-14
      
-  Using 10-222A engine support bridge spindle, lift 
up engine as far as possible. 
     
Note:  
     Lift engine only as far as possible without over-
stretching or damaging any pipes

Page 19 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-15
 
    
Note:  
Only loosen or lower subframe at front to avoid changing wheel 
alignment.  -  First remove front bolts -2- and -3- from subframe, then remove bolt -1-
. 
    
-  Using VAG1202A e

Page 20 of 33

AUDI A6 1996 C5 / 2.G AEB ATW Engines Lubrication System Components User Guide 17-16
      
Vehicles with manual transmission 
    
Vehicles with automatic transmission  -  Loosen left transmission mount nut (arrow) until it is aligned with lower 
edge of bolt (approx. 4 turns).
Page:   < prev 1-10 11-20 21-30 31-40 next >