coolant AUDI A6 1997 C5 / 2.G ATW Engine Motronic Fuel Injection Syst

24-6


Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AEB, ATW, Repair Group 26; Secondary Air Injection (AIR) system, checking
3 -
Oxygen Sensor (O2S) behind Three Way
Catalytic Converter (TWC) -G130-, 55 Nm Check Oxygen Sensor (O2S) and oxygen
sensor control behind Three Way Catalytic
Converter (TWC) Page 24
-87

Check oxygen sensor heater for Oxygen
Sensor (O2S) behind Three Way Catalytic
Converter (TWC) Page 24
-99

Removing and installing Page 24
-105
4 -
Combination valve for secondary air
injection (AIR)
Checking, removing and installing:
5 -
Engine Coolant Temperature (ECT) sensor
-G62-
Checking Page 28
-30
Pa
ge 7 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-7


Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AEB, ATW, Repair Group 26; Secondary Air Injection (AIR) system, checking
6 -
Fuel pressure regulator Checking Page 24
-33
7 -
Engine Speed (RPM) sensor -G28-
Checking Page 28
-26
8 -
Secondary Air Injection (AIR) solenoid
valve-N112-
Installation position Page 24
-14
, Fig.
4
Checking:Green harness connector
9 -
Bracket for harness connectors Component location Page 24
-13
, Fig.
1

Accessible with coolant expansion tank
unbolted and swung to the side.
Pa
ge 8 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-13


The following harness connectors are located below the coolant
expansion tank: Fig. 1 Installation location, harness connectors
1 - 4-pin harness connector, brown
for Oxygen Sensor (O2S) behind Three Way Catalytic Converter
(TWC) -G130- and Oxygen Sensor (O2S) Heater 1 -Z29- (bank 1
sensor 2)
2 - 6-pin harness connector, black
for Heated Oxygen Sensor (HO2S) -G39- before catalytic converter
and Oxygen Sensor (O2S) Heater -Z19- (bank 1 sensor 1)
3 - 3-pin harness connector, gray
for Engine Speed (RPM) sensor -G28-
4 - 3-pin harness connector, blue
for Knock Sensor (KS) 2 -G66-
5 - 3-pin harness connector, green
for Knock Sensor (KS) 1 -G61-

Fuel Pump (FP) Relay -J17- is located at position 4 of central electrics in
driver's footwell, left. Fig. 2 Component locations Fuel Pump (FP) Relay -J17-
Pa
ge 14 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-28

Idle speed (RPM), checking


Special tools and equipment

or
Test requirements:
VAS5051 with VAG5051/1VAG1551 with VAG1551/3AExhaust system free of leaks. Coolant Temperature at least 80 C. Electrical consumers switched off (radiator fan must NOT run during
test). A/C switched off. No pressure gauge connected. Vehicles with automatic transmission Selector lever in P or N.
Pa
ge 30 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-61
Component location Overview of component
locations Page 24
-5

Test requirements:

Coolant Temperature at least 80 C.

Electrical consumers switched off (radiator
fan must NOT run during test).
A/C switched off.

Checking function

- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Engine
must run at idle.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
button to confirm input.
Basic Setting
Q
Enter displa
y group number XXX

When indicated on display
- Press buttons -0-, -0- and -2- to select "display group number 002" and
press -Q- button to confirm input. When indicated on display
Pa
ge 70 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1