lock AUDI A6 1998 C5 / 2.G 01E Transmission Clutch Mechanism Service Workshop Manual

30-2


Pedal cluster, assembly overview

Repair Manual, Brake System, Repair Group 46

1 -
Mounting bracket
Detach steering column from steering box
before removing
2 -
Pivot pin
For clutch pedal and brake pedalInstallation position: groove (arrow)
towards clutch pedal
3 -
Locking clip
4 -
Hex socket head bolt, 25 Nm
5 -
Brake pedal
Pa
ge 2 of 27 Clutch mechanism, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.1

30-3


6 -
Clutch pedal
Removing and installing Page 30
-5
7 -
Pin
Clip onto clutch pedal
8 -
Locking clip
9 -
Master cylinder Removing and installing Page 30
-17
Do not operate clutch pedal after slave
cylinder has been removed.
10 -
Hex socket head bolt, 20 Nm
11 -
Mounting Insert in mounting bracket with over-center
spring
Pa
ge 3 of 27 Clutch mechanism, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.1

30-9


Clutch Pedal Position (CPP) switch -F 194-,
removing and installing

Note
The clutch pedal position (CPP) switch -F194-
ensures that the engine can only be started with the
clutch pedal depressed.
1 -
Mounting bracket
2 -
Cable bracket
3 -
Fuse
4 -
Bolt
Lock into clutch pedal
5 -
Clutch pedal Removing and installing Page 30
-5
Pa
ge 9 of 27 Clutch mechanism, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.1

30-19


Repair Manual, Body Interior, Repair Group 68
- Remove both socket head bolts (arrows).
- Remove driver's side storage compartment:

- Remove clutch pedal from master cylinder. To do this, pry out bolt lock
using screwdriver (arrow -1-), remove bolt (arrow -2-) and depress
clutch pedal.
Pa
ge 19 of 27 Clutch mechanism, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.1

30-23


- Tighten socket head bolt (arrow) for pedal assembly to 25 Nm.
- Connect master cylinder to clutch pedal. Engage bolt lock into clutch
pedal.
- Bleed clutch system after installing master cylinder Page 30
-25
.

Note:
Connect clutch master cylinder with clutch pedal. Engage bolt lock in
clutch pedal. - Check adjustment of switch -1- above clutch pedal as follows:

Switch -1- must lie against clutch pedal -3- completely and must be
completely activated.
Adjustment tolerance: gap measurement -a- between retaining clip
and mounting bracket -2- or gap measurement -b- at switch -1-
may be a maximum of 0.5 mm.
To adjust, hold clip and rotate switch -1-.
Pa
ge 23 of 27 Clutch mechanism, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.1