lock AUDI A6 1998 C5 / 2.G 01E Transmission Final Driveshaft Service Workshop Manual

is essential to check whether correct
adjustment of the driveshaft rectifies the fault
before replacing the driveshaft.
After removing the driveshaft from the rear final
drive, the additional balance disc (thick washer)
that may be located between the lock plate and
the bolt head must not be reinstalled.
Pa
ge 2 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9

39-65


1 -
Rear final drive
2 -
Gasket
Always replacePull off backing foil, and stick self-adhesive
side of gasket to drive flange. Remove grease from drive flange
3 -
Constant velocity joint Maximum permissible angle of deflection
8
4 -
Lock plate
5 -
Hex socket head bolt, 55 Nm
Self-lockingAlways replaceThreads for bolts in drive flanges must
always be cleaned (e.g. with a thread tap)
Pa
ge 3 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9

39-66


6 -
Universal joint
Maximum permissible angle of deflection
25
7 -
Shim
Determining thickness Page 39
-76
8 -
Hex bolt, 23 Nm
9 -
Driveshaft center mounting
10 -
Driveshaft
Adjusting Page 39
-75
11 -
Hex socket head bolt, 55 Nm
Self-lockingAlways replaceThreads for bolts in drive flanges must
always be cleaned (e.g. with a thread tap)
Pa
ge 4 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9

39-67


12 -
Lock plate
13 -
Constant velocity joint
Maximum permissible angle of deflection
8
14 -
Gasket
Always replacePull off backing foil, and stick self-adhesive
side of gasket to drive flange. Remove grease from drive flange
15 -
Transmission
Pa
ge 5 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9

39-71

Installing
Installation is carried out in the reverse order,
when doing this note the following:

Note:

It is essential that the locking fluid remaining in
the threads in the drive flanges on the
transmission and rear final drive is cleaned out
after removing the driveshaft. Otherwise there
is a danger that the new bolts will seize when
they are screwed in and then shear if they have
to removed later.
The threaded holes can be cleaned with a
thread tap.
Replace the gaskets on the drive flanges
(remove backing foil and stick gaskets onto
drive flange; make sure that the surfaces are
free of grease).

To prevent imbalance, the flanges on the driveshaft -A- and on the
rear final drive -B- must be installed so that the factory markings (or
the markings made on removal) are in alignment (arrows). If a new driveshaft is being installed and the factory paint marking on
the rear final drive flange is no longer visible, the radial run-out at the
flange for the driveshaft must be measured Page 39
-73
, and the
paint marking on the driveshaft must be aligned with the marking on
Pa
ge 9 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9

the flange. After removing the driveshaft from the rear final drive, the additional
balance disk (thick washer) that may be located between the lock
plate and the bolt head must not be reinstalled. Always replace all
flange bolts after disassembling. Replace driveshaft bolts (self-locking).
Pa
ge 10 of 19 Driveshaft, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.39.9