display AUDI A6 2000 C5 / 2.G AEB Engine Motronic MFI And Ignition System

24-44

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -1- to input display group number 41, and
press -Q- button to confirm input.
Read Measuring Value Block 41 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 59 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-45

- Compare display and specified values (display
fields 3 and 4):

Display fields

1 2 3 4
Display group 41: Oxygen Sensor (O2S) heater, before and after Three Way Catalytic Converter (TWC)
Display
xx.x
Htg.bC.ON/Htg.bC.OFF
xx.x
Htg.aC.ON/Htg.aC.OFF
Indicates Resistance of Oxygen
Sensor (O2S) heater
before TWC O2S heater on
or
O2S heater off
(before TWC) Resistance of oxygen sensor
(O2S) heater
(after TWC) O2S heater on
or
O2S heater off
(after TWC)
Range --- ---
0.0-65.0
---
Specified
value --- ---
4.9-19.9
Htg.aC.ON

--- --- If not as specified Page
24
-46
, Continuation
---
If displayed values are OK (as specified):

-
Press button to advance program
sequence.
-
Press buttons -0- and -6- to select "End Output"
Pa
ge 60 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-47


If display = Htg.aC.ON:
If display is switching between "Htg.aC.ON" and "Htg.aC.OFF" - Connect multimeter between harness connector terminals 1 and 2 (to
ECM), using VW 1594 connector test kit.
- Measure voltage supply and check display in display group 41, display
field 4.
Specified value: 11.0-14.5 volts Specified value: 0.0-12.0 volts (oscillating)
Pa
ge 63 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-49
If there is voltage:

If display = Htg.aC.ON:
If display switches between "Htg.aC.ON" and "Htg.aC.OFF:" - Connect multimeter between harness connector terminal 2 (to ECM)
and Battery Positive Voltage (B+), using VW 1594 connector test kit.
- Measure voltage supply and check display in display group 41, display
field 4.
Specified value: 11.0-14.5 volts Specified value: 0.0-12.0 volts (oscillating)
- Switch ignition off.
Pa
ge 65 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-52

Function test

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -4- to input display group number 34, and
press -Q- button to confirm input.
System in Basic Setting 34 1 2 3 4

Indicated on display (1-4 = display fields)
Note:
To be sure that the temperature is within the specified range, the specified
RPM has to be maintained for at least 1 minute. Observe status of oxygen
sensor control in display field 4. - Increase engine speed to 1800-2200 RPM and compare display with
specified values for oxygen sensor aging (display fields 1-4).
Pa
ge 68 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-53


Display fields

1 2 3 4
Display group 34: Oxygen sensor aging (time period check of oxygen sensor)
Display xxxx RPM xx.xx ms xx.xx s Test OFF/Test ON
B1-S1 OK/B1-S1 n.OK
Indicates Engine speed
(in 40 RPM steps) Engine load Time period oxygen sensor Diagnostic status
Diagnostic result
Range 0-6800 RPM 0.00-8.50 ms 0.00-5.00 s ---
Specified value 1800-2200 RPM 0.8-2.0 ms 0.00-3.30 s B1-S1 OK

--- --- If not as specified Page 24
-54
, Continuation
Pa
ge 69 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-54

Continuation
If displayed value is NOT OK (not as specified):

- Road test to condition oxygen sensor (eliminate
possible contamination) and repeat test.
If displayed value is still NOT OK:

- Replace HO2S -G39-.

- Check readiness code Page 01
-59
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code Page 01
-62
.
Pa
ge 70 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-55

Engine operating conditions (engine
electronics), checking


Note:
This test checks whether the Motronic Engine
Control Module (ECM) -J220- recognizes the
engine operating conditions.

Required special tools and test equipment

VAG 1551 or VAG 1552 scan tool with VAG
1551/3 adapter

Test requirements
Engine oil temperature at least 80 C (176
F)

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Pa
ge 71 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

Read Measurin
g Value Block
HELP
Input display group number XXX

Indicated on display
- Press buttons -0-, -0- and -5- to input display group number 5, and
press -Q- button to confirm input.
Read Measuring Value Block 5 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 72 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-56

- Check engine operating conditions (display field
4):

Display fields

1 2 3 4
Display group 5: Engine electronics-operating conditions
Display xxx RPM xx.xx ms xxx km/h Idle
Part throt
Full throt
1)

Decel
Enrich
Indicates Engine speed
(in 40 RPM steps) Engine load Vehicle speed Operational condition
Range 0-6800 RPM 0.00-8.50 ms --- ---
Specified value 760-960 RPM 0.50-1.50 ms 0 km/h Idle: "Idle"
Throttle slightly open: "Part throt"
Throttle quickly closed: "Decel"
Quick acceleration over 3000 RPM: "Enrich"
1) Possible only while driving
Pa
ge 73 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1