wheel AUDI A6 2000 C5 / 2.G ATQ Engine Ignition System Checking Workshop Manual

28-3
Technical data, ignition

Engine identification
ATQ (2.8 L / 5V/ 147 kW-engine)
Idle speed
Engine speed cannot be adjusted, it is regulated by idle stabilization 720 to 820 RPM (front wheel drive)
630 to 730 RPM (all wheel drive)
Engine speed (RPM) limitation
via fuel injector shut-off
about 6800 RPM
Ignition timing is determined in the control module
It is not possible to adjust the ignition timing
Ignition system Dual-spark ignition system with three ignition coils
Spark plugs Tightening torque 30 Nm.
Firing sequence 1-4-3-6-2-5
Pa
ge 4 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-50

- Repair open circuit or short circuit if
necessary.

- If, after erasing DTC memory for the sake of the
test, a DTC relating to the Camshaft Position
(CMP) sensor (hall sensor) is indicated again,
even though all previous tests were OK, the
following malfunction is possible:


Shutter wheel for Camshaft Position (CMP)
sensor is not aligned properly.

Check phase position of Camshaft Position
(CMP) sensor

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Engine must run at idle for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input display group number XXX

When indicated on display:
Pa
ge 56 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-51


Display fields

1 2 3 4
Display group 093: Phase position of Camshaft Position (CMP) sensor bank 1 and bank 2 with engine at idle.
Display xxx /min xx %
KW
KW
Indicated Engine
speed Engine
load Phase position
Bank 1 Phase position
Bank 2
Functional
range 630 to 6800
RPM 12 to 100
% -20 to 15 KW
-20 to 15 KW
Specified
value 720 to 820
RPM
1)
630 to 730
RPM 2) 12 to 26
% -20 to 15 KW
-20 to 15 KW
Notes

If specified values are not reached, unscrew Camshaft Position (CMP)
sensor and check whether shutter wheel is mounted properly at camshaft
(if mounted improperly, locking lug will get squished when mounting bolt is
tightened).
Repair Manual, Engine, Mechanical, Repair Group 13, removing and installing
toothed belt - Also check engine timing
1) Front Wheel Drive Vehicles 2) All-Wheel Drive Vehicles
Pa
ge 58 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-53


Display fields

1 2 3 4
Display group 014: Misfire recognition
Display xxxx/min xxx %
xxx
---
Indicated Engine speed
(RPM) Load
Number of combustion misfires
Misfire
recognition
Functional
range 670 to 6800
RPM 12 to
100 %
activated
locked
Specified
value 720 to 820
RPM
1)
630 to 730
RPM 2) 12 to 26
% 0 to 12
activated
Notes
If the specified value is exceeded: Check combustion
misfires of the individual cylinders Page 28
-54


1) Front Wheel Drive Vehicles 2) All-Wheel Drive Vehicles
If specified value is obtained:

-
Press button.Rapid data transfer
HELP

Indicated on display (function selection):
Pa
ge 61 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1