coolant reservoir AUDI A6 2000 C5 / 2.G ATW Engine Oxygen Sensor Control Workshop Manual

24-80
Evaluation display group 033 Display field:
2
Possible cause
Corrective action
constant about
0.450 V
Open circuit in wire 4 between oxygen sensor
and control module - Check primary voltage Page 24
-80


Open circuit in wire 3 between oxygen sensor
and control module
constant about
0.200 V Oxygen sensor faulty- Replace oxygen sensor
larger than
1.100 V Short circuit to B+ in wire 4 between oxygen
sensor and control module - Check oxygen sensor wiring, oxygen sensor
before catalytic converter Page 24
-81

smaller than
0.150 V
Short circuit to Ground (GND) in wire 4 between
oxygen sensor and control module

Checking primary voltage

Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant hoses
can remain connected. - Disconnect 4-pin harness connector -2- (black) to Heated Oxygen Sensor
(HO2S) -G39- before catalytic converter.
Pa
ge 10 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-81


If specified value is not obtained:
If specified value is obtained:
Checking oxygen sensor wires - Connect multimeter between terminal 3 and 4 for voltage
measurement.
- Switch ignition on.

Specification: 0.400 to 0.500 V
- Switch ignition off.
- Check oxygen sensor wiring.
- Replace Heated Oxygen Sensor (HO2S) -G39-.

Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 4-pin harness connector -2- (black) to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
Pa
ge 11 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-96

Checking primary voltage

Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 4-pin harness connector -1- (brown) to Oxygen Sensor
(O2S) behind Three Way Catalytic Converter (TWC) -G130-.

If specified value is not obtained:
If specified value is obtained: - Connect multimeter between terminal 3 and 4 for voltage
measurement.
- Switch ignition on.

Specification: 0.400 to 0.500 V
- Switch ignition off.
- Check oxygen sensor wiring.
- Replace Oxygen Sensor (O2S) behind Three Way Catalytic Converter
(TWC) -G130-.
Pa
ge 26 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-97

Checking oxygen sensor wires

Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 4-pin harness connector -1- (brown) to Oxygen Sensor
(O2S) behind Three Way Catalytic Converter (TWC) -G130-.
- Connect VAG1598/31 test box at wiring harness to Engine Control
Module (ECM), do not connect ECM Page 24
-19
.

- Check following wire connections for open circuit.Harness connector
Terminal
VAG1598/31 test box
Socket
3 68
4 69
Pa
ge 27 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-100

Test requirements:

Coolant Temperature at least 80 C.

Fuse for oxygen sensor heating OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Test sequence

or
Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 4-pin harness connector -2- (black) to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
- Disconnect 4-pin harness connector -1- (brown) to Oxygen Sensor
(O2S) behind Three Way Catalytic Converter (TWC) -G130-.
Pa
ge 30 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-105

Oxygen sensor, removing and installing


Special tools and equipment

3337 wrench, 7-piece set
Locking compound G 052 112 A3

Procedure

Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access harness connectors. The coolant hoses
can remain connected. - Disconnect 4-pin harness connector of oxygen sensor and lay it to
side.
1 - (brown) for Oxygen Sensor (O2S) behind Three Way Catalytic
Converter (TWC) -G130-
2 - (black) for Heated Oxygen Sensor (HO2S) -G39- before catalytic
converter
- Unscrew oxygen sensor using special tool 3337.
Pa
ge 36 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2