lock AUDI A6 2001 C5 / 2.G 01V Transmission Remove And Install Workshop Manual

37-74

All except 2.7 Liter 5V turbo engine:

- Remove cover above air filter housing.

For all 6 cylinder engines: - Remove air guide -1- between air filter housing and lock carrier.
- Disconnect connector for Evaporative Emission (EVAP) canister purge
regulator valve -2-, and remove valve from bracket. Disconnect
connector -3- at Mass Air Flow (MAF) sensor.
- Remove intake air duct -4- from intake manifold.
- Remove upper part of air filter housing -5-.
- Unbolt engine coolant expansion tank and lay aside.
- Remove Heated Oxygen Sensor (HO2S) from front exhaust pipes (left
and right).
- Remove upper securing nuts from front exhaust pipes (left and right).
- Assemble both 10-222A/3 engine support adapters for front and rear
spindles on support bar.

- Set 10-222A engine support bridge onto the fender mounting flanges
using 10-222A/1 brackets.
Pa
ge 4 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-92

- Place transmission onto transmission support.

- Secure transmission on 3282 transmission support using bolt -A-.
- Move transmission into position between the lowered subframe and
vehicle floor.

Note:
Do not deform lever/shift rod when pressing up or else shifting cannot be
precisely adjusted any more. - Press the lever/shift rod -2- at transmission completely toward rear
(toward right in illustration) until park lock is engaged.
- Shift selector lever into "P" and carefully press up ball head of selector
lever cable on lever/shift rod -2- using a pair of pliers.
- If installed, press securing brace (arrow) open at end of selector lever
cable.
- Align transmission properly to engine.
Pa
ge 22 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-98


Continuation for all vehicles
Radio operating manual
Tightening torque table Page 37
-119
onward. - Bolt heat shield -B- for driveshaft to Torsen differential cover (arrows) if
installed.
- Install heat shield -A- above driveshaft.
- Install bracket for noise insulation panel.
- Install noise insulation panel.
- Install front wheels.
- Connect battery Ground (GND) strap.
- Check adjustment of selector lever cable page 37
-45
.
- Check gear oil in final drive with transmission installed page 39
-1 .
- Then check ATF level and top off Page 37
-133
onward.
- After connecting battery, enter anti-theft code for radio.- Fully close power windows to stop.
- Then activate all power window switches ("up") for at least one second
to activate automatic window raising/lowering.
- Set clock to correct time.
Pa
ge 28 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-115


Note: - Press the lever/shift rod -2- at transmission completely toward rear
(toward right in illustration) until park lock is engaged.
- Shift selector lever into "P" and carefully press up ball head of selector
lever cable on lever/shift rod -2- using a pair of pliers.

Do not deform lever/shift rod when pressing up or else shifting cannot be
precisely adjusted any more.
Note:
Check whether the torque converter is still properly installed and has not
slid out of the converter housing toward the font:
Place intermediate plate onto bushings.Make sure that wires do not get pinched as transmission is docked at
engine.
- It must be possible to easily turn torque converter by hand without
much force.
Pa
ge 45 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

- Then activate all power window switches ("up")
for at least one second to activate automatic
window raising/lowering.

- Set clock to correct time.
Pa
ge 49 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2