display AUDI A6 2012 Owner's Guide

N -N eutr al
The transmission is in neutra l in this position .
Shift to this posit ion for standing with the
brakes applied
¢ &. in Driving the automatic
transmission on page 101.
When the veh icle is stationary or at speeds
be low 3 mph (5 km/h) , you must always apply
the footbrake before and while moving the
lever out of
N.
D /S -Normal position for dr iving forward
I n the D /S position, the transmission can be
operated e ither in the normal D mode or in
the S sport mode. To select the 5 sport mode,
pu ll the se lector lever back briefly . Pulling the
l ever back again will select the normal D
mode. The instrument cluster display shows
the selected driving mode.
In the
no rmal mode D , the transmission auto ­
matica lly selects the best gear ratio. It de­
pends on engine load, veh icle speed and the
dynamic control program (DRP).
Select the
s port mode S for sporty driving .
The vehicle makes full use of the engine's
power. S hifting is more noticeable when accel­
erating.
When the veh icle is stationary or at speeds
be low 3 mph (5 km/h), you must always apply
the foot brake before and while moving the lever to
D /S out of N .
In certain circumstances it may be advanta­
geous to temporarily switch to the manual
shift program to manually select gear ratios
to match specif ic driving conditions
¢ page 105.
A WARNING
Read and follow alt WARNI NGS ¢ A in
Driving the automatic transmission on
page 101.
(D Note
-
Coast ing downh ill with the transmission in
N and the engine not runn ing will result in
Automatic Tra nsmi ssi on 10 3
damage to the automatic transmission
and possib ly the cata lytic converter.
Automatic Shift Lock (ASL)
Applies to veh icles: w ith mult itronic
The Automatic Shift Lock safeguards you
against accidentally shifting into a forward or
the reverse gear and causing the vehicle to
move unintentionally.
0, N 0 0
0
a1i
) ( )
Fi g. 107 Shi ft ga te: selector leve r lock pos it ions and
i n te rlock bu tton highligh ted
The selector lever lock is re leased as follows:
.. Tu rn the igni tion on.
.. Step on the brake pedal.
At the same time
press and hold the inte rlock bu tton on the
side of the gear selector knob
Q fig. 107
with your thumb until yo u have moved the
selector lever to the desired posit ion .
Automatic selector leve r lock
The selector lever is locked in the P and N po­
s itions when the ig nition is tu rned on. To
move t he lever from these positions the driver
must depress the brake peda l. As a reminder
to the driver, the following warning appears in
the instrument cluster display when the selec­
tor is in
P and N :
When stationar y apply footbrake while se­
lecting gear
A time delay element p reven ts the selector
lever from locking when it is moved through
the
N position (going from R to 0 /5 ). The
locking element wi ll lock the se lector lever if
the lever is left in N (Neutral) for more than approximately 1 second, w ithout the brake
pedal being pressed .

Manual shift program
Applies to vehicles: with multitronic
Using the manual shift program you can
manually select gears .
Fig. 108 Center console: shi ftin g th e tip tronic ma nua l·
l y
Fig. 109 Display: man ual sh ift program, selected gea r
highl ighted
Switching to manual shift program
• Push the selector lever to the right from 0/
5 . As soon as the transmission has switched
over, the selected gear appears in the dis­
play.
To upshift
• Push the selector lever forward to the plus
pos ition
0 ~ fig . 108 .
To downshift
• Push the leve r to the minus position 0 -
When accelerating , the transmission will au­
tomatically shift into the next gear before the
engine reaches its maximum RPM .
If you apply a light throttle when accelerat­
ing, tiptron ic will automatically shift from 1st
to 2nd gear to save fuel. If you apply a heavy
thrott le, the transmission will stay in 1st gear
Automatic Transmission 105
until near maximum RPM is reached, or until
the driver shifts into 2nd gear.
If you take your foot off the accelerator pedal
when d riving down a steep incline, tiptronic
will downshift from the selected gear into the
next lower gear until it reaches 1st gear,
based on road speed and engine RPM. Auto­
matic downshifting is interrupted as soon as
you apply the throttle again.
(D Tips
- When you shift into the next lower gear,
the transmission will downshift only
when there is no possibility of over-rev­
ving the engine.
- When the kick-down comes on, the
transm ission w ill shift down to a lower
gear, depending on vehicle and engine
speeds .
- tiptronic is inoperative when the trans­
mission is in the fai l-safe mode.
Steer ing wheel with tiptronic
Applies to vehicles: with tiptronic steering wheel
The shi~ buttons on the steering wheel allow
the driver to shift gears manually.
Fig. 1 10 Steer ing w hee l: S hift bu ttons
• To downshift, touch the button on the left
0 -
• To upshift, touch the button on the right
0.
The shift buttons are activated when these­
lector lever is in
D/S or in the manual shift
program (tiptronic) .

108 Automatic Transmission
-If you must g et out of the vehicle, move
the selector lever securely into the P po­
sition and apply the parking brake f irmly.
-If the engine must remain running, never
have any driving position engaged when
checking under the hood. Make sure the
selector lever has securely engaged and
is locked in P with the parking brake
firmly set
r:!;> page 214, Engine compart­
ment.
Otherwise, any increase in engine
speed may set the vehicle in motion,
even with the parking brake applied.
Selector lever posit ions
Appl ies to vehicles: with tiptronic
This section describes the selector lever posi­
tions and driving ranges.
Fig. 113 Display in the instrume nt cluster: se lector
lever pos itio n
The selector lever position engaged appears
next to the selector lever as well as in the in­
strument cluster display.
P - Park
In this selecto r lever position the transmis­
sion is mechanically locked . Engage
P only
when the vehicle is
completely stopped ¢ A
in Driving the automatic transmission on
page 107 .
To shift in or out of position P, you must first
press and hold the brake pedal and then press
the release button in the selector lever handle
while moving the selector lever to or from
P.
You can shift out of this position only with the
ignition on.
You must release the parking lock manually
before towing the vehicle
<:!;>page 112.
R -Reverse
Select R only when the vehicle is at a full stop
and the engine is running at idle speed r:!;> ,& in
Driving the automatic transmission on
page 107.
Before you move the selector lever to R, press
both the button in the handle of the selector
l ever
and the brake pedal at the same time.
When the ignition is on, the backup lights illu­
minate when the selector lever is moved into
R.
N - Neutral
The transmission is in neutral in this position .
Shift to this position for standing with the
brakes applied
<:!;>page 109.
When the vehicle is stationary or at speeds
below 3 mph (5 km/h), you must always apply
the footbrake before and while moving the
lever out of
N.
D/S - Normal position for driving forward
In the D/S position, the transmission can be
operated either in the normal D mode or in
the S sport mode . To select the S sport mode,
pull the selector lever back briefly. Pulling the
lever back again will select the normal D
mode. The instrument cluster display shows
the selected driving mode.
In the
normal mode D , the transmission auto­
matically selects the best gear ratio.
It de­
p ends on engine load, vehicle speed and the
dynamic control program (DRP).
Select the
sport mode S for sporty driving.
The vehicle makes full use of the engine's
power. Shifting is more noticeable when accel­
erating.
When the vehicle is stationary or at speeds
below 3 mph (5 km/h), you must always apply
the foot brake before and while moving the
lever to
D/S out of N .
In certain circumstances it may be advanta­
geous to temporarily switch to the manual
shift program to manually select gear ratios .,..

to match specific driving conditions
¢page 110.
A WARNING
Read and follow all WARNINGS ¢.& in
Driving the automatic transmission on
page 107.
(D Note
Coasting downhill with the transmission in
N and the engine not running will resu lt in
damage to the automatic transmiss ion
and possibly the catalytic converter.
Automatic Shift Lock (ASL)
Appl ies to vehicles: with tiptro nic
The Automatic Shift Lock safeguards you
against accidentally shifting into a forward or
the reverse gear and causing the vehicle to
move unintentionally .
I
Fig. 114 Shift gate selector lever lock pos itions and
inte rlock butto n highlighted
The selector lever lock is released as follows :
• Turn the ignition on.
• Step on the brake peda l.
At the same time
press and hold the interlock button on the
side of the gear selector knob¢
fig. 114
with your thumb until you have moved the
selector lever to the desired position .
Automatic selector lever lock
"' N 0 0 (!)
cb
The selector lever is locked in the P and N po­
sitions when the ignition is turned on. To
move the lever from these positions the driver
must depress the brake pedal. As a reminder
to the driver, the following warning appears in
Automatic Transmission 109
the instrument cluster display when the selec ­
tor is in
P and N :
When stationary apply footbrake while se­
lecting gear
A time delay element prevents the selector
lever from locking when it is moved through
the
N posi tion (going from R to D/S ). The
locking element will lock the selector lever if
the lever is left in N (Neutral) for more than
approximately 1 second, without the brake
pedal being pressed .
At speeds above abo ut 3 mph (5 km/h) the
Automatic Shift Lock is automatically deacti­
vated in the
N position .
Interlock button
The lock button on the selecto r lever prevents
the lever from being accidentally shifted into
certain positions. Pressing this button deacti­
vates the selector lever lock. Depending on
the direction of the shift, the selector lever
locks at different positions . The positions are
highlighted in the illustration¢
fig. 114.
Kick-down
App lies to vehicles: wit h tiptro ni c
The kick-down feature allows the vehicle to
generate maximum acceleration .
When you press the accelerator pedal beyond
the resistance point that is reached at full
throttle, the transmission will select a lower
gear ratio based on vehicle speed and engine
RPM. The engine RPM will be controlled to
produce maximum vehicle acceleration as
long as you continue to press the accelerator
pedal beyond this resistance point .
_&. WARNING
Be careful when using the kick-down fea­
ture on slippery roads. Rapid acceleration
may cause the vehicle to skid .
-

Parking system
General information
Appl ies to vehicles: Audi parking system plus/Audi park­
ing system plus with rear view camera
Depending on your vehicle's equipment, vari­
ous parking aids will help you when parking
and maneuvering.
The
Audi parking system plus assists you
when parking by providing audio and visual
warn ings about objects
in front of and behind
the vehicle ¢page 113.
The Audi parking system plus with rear view
came ra
shows the area behind the vehicle in
the display . This image helps you when paral­
lel parking or cross parking. The system also
provides the parking aid aud io and visual sig­
nals
~ pag e 114 .
@ Tips
For information on cleaning , refer to
q page206.
Audi parking system
plus
De script ion
Appl ies to vehicles: with parking system plus
Audi parking system plus provides audio and
visual signals when parking .
Sensors are located in the front and rear
bumpers . If these detect an obstacle, audible
and v isual signals warn you. The range at
which the sensors begin to measure is approx ­
imately:
front
rear side
center
side
center
--~-
3 ft (0.90 m)
4 ft (1.20 m)
2 ft (0.60 m)
5.2 ft (1.60 m)
The closer you get to the obstacle, the shorter the interval between the audible signa ls. A
continuous tone sounds when the obstacle is
less than approximate ly 1 foot (0.30 meters)
away. Do not continue driving farther!
Parking system 113
If the distance to an obstacle remains con­
stant, th e volume of the distance warning
gradually drops after about four seconds (this
does not apply in the continuous tone range).
Switching on and off
Applies to vehicles: with parking system plus
Fig. 119 Ce nt er co nsol e: Parkin g sy ste m sw it c h
Fig. 120 MMI di splay : v is u al d istance display
Switching on
.. Switch the MMI on
.. Activate
comfort or auto mode in Audi drive
select
q page 95.
.. Shift into reverse or
.. Press the switch~ in the center conso le
q fig. 119 . A short confirmation tone
sounds and the indicator light in the switch
lights up.
Switching off
.. Drive faster than 6 mph (10 km/h) , or
.. press the switch
~ or
.. switch off the ignition.
Segments in the visual display
The red segments in front of and behind the
vehicle
¢ fig. 120 help you to determine the
distance between you and an obstacle. As
your vehicle comes closer to the obstacle, the .,..

114 Park in g s yste m
segments move closer to the vehicle. The col­
lision area has been reached when the next to
l ast segment is displayed. Do not cont inue
driving farther
c:> &.!
A WARNING
-Sensors have blind spots in which objects
cannot be detected . Pay special attention
to small children and animals because
the sensors cannot always detect them .
- The parking system cannot replace the
dr ive r's attention. The driver alone is re­
sponsible for parking and similar driving
maneuvers.
- Always keep your eyes on the veh icle's
surround ings, using the rear view mirror
as well.
(D Note
Low obstacles al ready signaled by a warn­
ing can disappear from the system's detec­
tion range as they are approached and will
not con tinue to be signa le d . Obje cts such
as barrier cha ins, trailer draw bars, thin
pa inted vertical poles or fences may not be
detected by the system, posing risk of
damage.
@ Tips
- The sensors must be kept clean a nd free
of snow and ice for the park assist to op­
erate.
- You can change the volume and pitch of
the signals as well as the display
<=>page 118.
-What appears in the display is time -de ­
l ayed.
Audi parking system
plus with rear view
camera
Introduction
Applies to vehicles : pa rkin g system p lus wit h rear view
came ra
Fig. 121 Parking mode 1: reverse parking
Fig. 122 Park ing mode 2: parallel parkin g
This park ing system integ rates a r e arvi ew
cam era
in addition to the audio and v isual
parking system signa ls
<=> page 113.
0 ± .. a,
You can choose between two modes to assist
yo u w ith parking. For example, you can use
"pa rking mode 1" when parking in a park ing
space or garage
c:> fig. 121. When you want to
park para llel to the edge of the st ree t, select
"pa rking mode 2"
<=>fig. 122.

General Information
Applies to vehicles: with parking system plus wit h rea r
view came ra
Fig. 123 Area cove red (D and area not covered @by
the rear vi ew camera.
Fig. 124 Rear lid: Loc ation of the rear view came ra
Rear view camera coverage area
The MMI display shows the area covered by
the rear view camera
c::> fig. 123 @. Objects
that are not in the area covered @are not
shown on the MMI display.
We recommend that you practice parking with
the rear view camera in a traffic -free location
or parking lot to become familiar with the sys­
tem, the orientation lines, and their function.
When doing this, there should be good light
and weather conditions.
In the MMI display, objects or vehicles appear
closer or further away if:
- you are driving in reverse gear from a level
surface onto an incline or a downward slope,
- you are driving in reverse gear toward pro­
truding objects,
- the vehicle is carrying too much load in the
rear.
The accuracy of the orientation lines and blue
surfaces dimin ishes if:
Parking system 115
- the rear view camera does not provide a reli­
able image, fo r example, in poor visibility
conditions or if the lens is dirty,
- the image on the screen is not visible due to
sun glare and reflection.
Caring for the rear view camera lens
The rear view camera is located above the rear
l icense plate bracket. For the parking system
to operate, the lens
c::> fig. 124 must be kept
clean:
- Dampen the lens with a household alcohol­
based glass cleaner, and then wipe the lens
clean with a dry cloth
c::> Q) .
-Remove snow with a hand brush and ice
preferably with a de-icing spray
c::> (i) .
_& WARNING .. --- Sensors have blind spots in which objects
cannot be detected. Pay special attention
to small children and animals because
the sensors cannot always detect them.
- The parking system cannot replace the
driver's attention. The driver alone is re­
sponsible for parking and similar driving
maneuvers.
- Always keep your eyes on the vehicle's
surroundings, using the rear view mirror
as well.
- Do not allow yourself to be distracted
from traffic by the rear view camera pic­
tures.
- If the position and the installation angle
of the camera has changed, for example,
after a rear end collision, do not continue
to use the system for safety reasons .
Have it checked by a qualified dealership.
(D Note
-Low obstacles already signaled by a
warning can disappear from the system's detection range as they are approached
and w ill not continue to be s ignaled. Ob­
jects such as barrier chains, trailer draw
bars, thin painted vertical poles or fen­
ces may not be detected by the system,
posing risk of damage .

116 Parking system
-Never use warm or hot water to remove
snow or ice from the rear view camera lens -this could cause the lens to crack!
- When cleaning the lens, never use prod­
ucts that are abrasive.
Switching on and off
Applies to vehicles: with pa rk in g system plus w it h rear
view ca mera
The rear view camera switches on automati­
cally together with the acoustic and visual
park assist when you put the vehicle in re­ vers e.
Switching on
• Switch the MMI on
• Activate
comfort or auto mode in Audi drive
select
r::!;) page 95.
• Shift into reverse or
• Press the switch
l""I in the center console
r::!;)page 113, fig. 119. A short confirmation
tone sounds and th e indicator light in the
switch lights up.
Switching between the rear view camera
and visual display
• Press the Graphic control button
r::!;) page 117 , fig . 12 S @ to see the visual
display .
• Press the
Rearview control button to see
the rear view camera image
r::!;) page 113,
fig . 120 .
Switching off
• Drive faster than 6 mph (10 km/h), or
• press the switch
I"" I or
• switch
off the ignition.
A WARNING
-The MMI display cannot show, or cannot
adequately show, certain objects (such as
small posts or grating), recesses in the
ground and protruding parts on another
car.
- Only use the rear view camera to assist
you if it shows a good, clear picture. For
example, the image may be affected by the sun shining into the lens, dirt on the
lens or if there is a defect .
- Use the rear view camera only with the
rear lid completely closed. Make sure any
objects you may have mounted on the
rear lid do not block the rear view cam­
era .
(!) Tips
-The sensors must be kept clean and free
of snow and ice for the park assist to op­
erate.
- If your vehicle is near an obstacle, an ad­
ditional visual indicator appears in the
rearview camera image . This superim­
posed image is there to help you to de­
termined which area of the vehicle is af­
fected.
- You can change the volume and pitch of
the signals as well as the display
r::!;) page 118.
-What appears in the display is time-de­
layed .

Reverse Parking
Applies to vehicles: with parking system plus with rear
view camera
Parking mode 1 can be used when parking in
a garage or into a parking space.
Fig. 125 MMI display: a iming at a park ing spot
Fig. 126 MMI display: aligning the vehicle
• Switch the MMI on and select reverse gear.
• Turn the steering wheel until the orange
orientation lines
(D appear in the parking
spot¢
fig. 125. Use the markings @to help
you estimate the distance from an obstacle .
Each marking represents 3
ft (1 meter). The
blue area represents an extension of the ve­
hicle's outline by approximately 16
ft (5 me­
ters) to the rear.
• While driving in reverse gear, adjust the
steering wheel angle to fit the parking space
with the aid of the orange orientation lines ¢ (D. @ marks the rear bumper. Stop the
vehicle when the red orientation line© bor­
ders an object¢ £!
A WARNING
-The rear view camera does not show the
entire area beh ind the veh icle
¢p age 115, fig. 123. Watch out espe­
cially for smal l children and animals. The
Parking system 117
rear view camera cannot always detect
them, posing risk of an accident!
- Please note that objects not touching the
ground can appear to be further away
than they really are (for example, the bumper of a parked vehicle, a trailer
hitch, or the rear ofa truck). In this case,
you shou ld not use the help lines to help
with parking, which poses danger of an accident!
(D Note
In the MMI d isplay, the direction of travel
of the vehicle rear is represented depend­
ing on the steering wheel angle. The vehi­
cle front swings out more than the vehicle
r ear. Maintain plenty of distance so that
your outside mirror or a corner o f your ve­
hicle does not collide with any obstacles.
This can damage to your vehicle.
Parallel Parking
Applies to vehicles: with parking system plus with rear
view camera
Use parking mode 2 to help you parallel park
along the side of a street.
Fig. 127 MMI display: blue surface in the park ing spot
Fi g. 128 MMI display: Blue curve on the curb

118 Parking system
The following steps app ly only when there is
no obstacle such as a wall near the parking
spot. Otherwise, please read the informat ion
prov ided in the "Parking Next to Obstacles"
section <=>
page 118.
.. Activate the turn signal.
.. Position your vehicle parallel to the edge of
the street, approximately 3 ft (1 meter)
from a parked vehicle.
.. Switch the MM I on and se lect reverse gear .
The parking aid turns on and parking mode
1 appears on the display .
.. Press the cont ro l button @<=>
fig. 12 7 on
t h e M MI con trol conso le. Par kin g mode 2
appears .
.. Back up and align yo ur vehicle so the b lue
area @ borders on the rear end of the vehi­
cle or on the parking spot line. The bl ue area
represents an extension of the veh icle's out­
li ne by approximate ly 16 ft (5 meters) to the
rear . The long side of the blue area should
be o n the cu rb. The entire blue area must fit
into the parking spot .
.. Wi th the veh icle stopped, turn the s teer ing
wheel to the right as far as it w ill go.
.. Back into the park ing spot until the blue
c ur ve to uches the curb<=>
fig. 128. Stop the
vehicle.
.. With the veh icle stopped, turn the steer ing
wheel to the left as far as it will go.
.. Co nti nue to back in to the parking spot until
the veh icle is parked para llel to the curb .@
marks the rear bumper . Stop the vehicle
when the red orientation line@ borders an
obje ct ¢
& -Keep an eye on the front of
yo ur vehicle while doing this ¢0 .
Parking n ext to obstacles
When t here is an obstacle (such as a wall)
next to the pa rk ing spot, choose a spot w ith
mo re space on t he sides. Pos ition the long
side of the blue area so that there is sufficie nt
sp ace from the curb. The area m ust no t be on
the c urb. Yo u will also need to start turning
the steering wheel much earlier. There should
be a suffic ient amo unt of space between the
curb and the b lue curve, and the blue c urve
c;> fig. 128 mus t not touch the curb.
A WARNING
- The rear view camera does not show the
entire area behind the vehicle
c::;, page 115, fig . 123 . Watch out espe­
cially fo r small ch ildren and anima ls . T he
rea r view came ra ca nnot always de te ct
them, posing ris k of an acciden t!
- P lease note that objects not touching the
g round can appear to be further away
t han they really are (for examp le, the
bumper of a par ked vehicle, a trai ler
hitch, or the rea r of a truck) . In this case,
you shou ld not use the help lines to help
with parking, wh ic h poses danger of an
accident!
(D Note
In the MMI display, the direction of travel
of the vehicle rear is represented depend­
i ng on the steering wheel angle . The vehi­
cle front swings out more than the vehicle rear . Maintain plenty of dista nce so that
your outside mi rror or a corner of you r ve ­
hicle does not col lide with any obstacles.
This can damage to your ve hicle .
(D Tips
The left o r right orie ntation lines and su r­
faces will be disp layed, depending on t he
tu rn s ignal being used .
Adjusting the display
and warning tones
Applies to vehicles: with parking system plus or parking
system plus with rear view camera
The display and warning tones can be adjust ­
ed in the MMI.
.. Select: !CAR ! function b utton> Car sy stems
cont ro l but to n > Driver a ssi st > Parking aid
> Setting s control b utton .
Display
On* -turns on the visual d isplay for pa rking
system p lus and shows the rearview came ra
i mage fo r the park ing system p lus w ith rea r
view camera*. ..,_