spare wheel AUDI A6 2015 User Guide

272 What do I do no w?
• Always store the vehicle too l kit, the jack*
and the replaced tire in the luggage com­
partment
¢ page 132.
• Unhook the cargo floor before clos ing the
rear lid.
Using th e spare tir e (compac t spare tir e)
The compact spare tire is on ly intended for
emergencies until yo u can reach a repair shop.
Replace it as quickly as possible with a stand­
ard wheel and tire.
There are some restrictions on the use of the compact spare tire. The compact spare tire has been des igned specifically for your type of
vehicle. It must not be swapped with a com­ pact spare tire from another type of vehicle.
Sn ow chain s
For technical reasons, the use of snow chains
on the compact spare tire is
not permitt ed .
If you do have to dr ive with snow cha ins and a
front tire fails, mount the spare wheel with
tire instead of a rear tire . Install the snow
chains on the rear tire and use it to replace
the defective front tire.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators .
- If the spare tire is more than 6 years o ld,
use it only in an emergency and with ex­
t reme caution and careful driving .
- The spare tire is intended only for tem­
porary and short-term use. It should be
replaced as soon as possible w ith the
normal wheel and t ire.
- After mounting the compact spare tire,
the tire pressure must be checked as
soon as poss ible. The tire pressure of the
c ompact spare tire must be 4.2 bar; oth­
erwise, you risk hav ing an accident .
- Do not drive faster than 50 mph (80 km/
h). You risk having an acc iden t.
- Avoid full-throttle acce le rat ion, heavy
braking, and fast corner ing . You risk hav­
ing an a cc ident. -
Never drive using more than one spare
wheel and tire. You r isk having an acci­
dent.
- Normal summer or winter tires must not
be mounted on the compact spare wheel
rim.
- For technical reasons, the use of tire
chains on the spare tire is not permitted.
If it is necessary to drive with tire chains,
the spare wheel must be mounted on the
front ax le in the event of a flat in a rear
tire. The new ly available front wheel
m ust then be installed in place of the
rear whee l w ith the flat tire. Installing
the tire chain before mounting the whee l
and tire is recommended.
- Loose items in the passenger compart ­
ment can cause serious personal injury
during hard braking or in an accident. Never store the inflatable spare tire or
jack and tools in the passenger compart­ ment.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel.
• After you experience a t ire failure, pull the
car well away from mov ing traffic and t ry to
reach
l e vel ground before you stop ¢ ,&.
• All passengers should leave th e car and
move to a safe location ( for instance, behind
the guardrail) ¢,& .
• Engage the
par king brake to prevent your
vehicle from rolling unintentionally c> _& .
• Move
selector le ver to pos it ion P c> _& .
• If you are towing a trailer, unhitch the trailer
from your vehicle.
• Take the
jack and the spare tir e out of the
luggage compa rtment c>
page 271,
i=> page 271 . ..,_

M N
0 <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
A WARNING 1=
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- If you have a flat tire, move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed. When one
front wheel is lifted off the ground, plac­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 132.
{!) Tips
Before changing the wheel, you must acti­
vate the jacking mode, so that the auto­ matic controls for the Adaptive Air Sus­
pension* do not make it more difficult to
lift the vehicle with the jack¢
page 2 75.
Changing a wheel
When you change a wheel, follow the se ­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
c::;. page 275.
-
2. Remove the decorative wheel cover* . For
more details see also
¢page 274, Deco­
rative wheel covers
or ¢ page 2 7 4,
Wheels with wheel bolt caps.
3. Loosen the wheel bolts¢ page 274.
What do I do now? 273
4.
5.
6.
7.
8.
9.
Locate the proper mounting point for the
jack and align the jack below that point
¢page 275.
Raise the car with the jack ¢page 275.
Remove the wheel with the flat tire and
then install
the spare <=> page 2 76.
Tighten all wheel bolts lightly.
Lower the vehicle with the jack .
Use the wheel bolt wrench and
firmly
tighten all wheel bolts¢ page 274 .
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI function button > (Car)* sys­
tems
control button > Servicing & checks
> Air susp.: jack mode > Off .
The vehicle jack mode* switches off automati­
cally at speeds above 6 mph (10 km/h).
A WARNING
Always read and follow all WARNINGS and information<=>
A in Raising the vehicle on
page 275
and <=> page 277.
After changing a wheel
A wheel change is not complete without the
doing the following.
.,. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment
c::;. page 132.
.,. Check the tire pressure on the spare wheel
immediately after mounting it.
.,. As soon as possible, have the
tightening
torques
on all wheel bolts checked with a
torque wrench. The correct tightening tor­
que is
90 ft lb (120 Nm) .
.,. Have the flat tire
replaced as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to turn while
changing a tire, they should be replaced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
ll>
•
•

276 What do I do now?
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you a re
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­ matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles: with sill
Fig . 211 Sill: remov ing t he cover
.. Pull the cover down to remove it¢ fig . 211.
.,. To install the cover again , insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
(D Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off /installing the spare
Follow these instructions st ep-by-step for
changing the wheel.
Fig. 212 Changing a wheel: using the screwdrive r han­
dle (w it h th e blade re m oved) to turn the bolt s
Fig. 213 Changing a wheel: alignment p in ins ide t he
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top­
most wheel bolt and set it aside on a
clean
surface ¢ fig. 212 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 213 .
.,. Then remove the other wheel bolts as de­
scribed above .
.. Take off the wheel leaving the alignment pin
in the bolt hole
¢(D . Ill>

M N
0 <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Putting on the spare wheel
"'Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
"' Remove the alignment pin and insert and
t ighten the remaining wheel bolt s lightly
like the rest .
"'T urn the jack handle counte r-clockw ise to
lower the vehicle unt il the jac k is f ully re­
l eased .
"' Use the whee l bolt wrench to tighten a ll
whee l bolts firmly
¢ page 274. Tighten
them
crosswis e, from one bolt to the (ap­
proximate ly) opposite one, to keep the
wheel cen tered.
When removing or install ing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
{D) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversib le blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
un id ire ctional
tread design
make s ure the tread pat­
tern is poi nted the right way
¢ page 277.
- The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove a ll dir t from these
su rfaces before remo unting the wheel.
What do I do now? 277
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Usi ng a spa re ti re with a tre ad patte rn
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection, please
note the following :
- The d irect ion of rotation is marked by an ar­
row on t he side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the t ire will not be able to
achieve its optimum performance cha racte r­
istics w it h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu lar at­
ten tion to th is fact during we t wea ther and
t ha t you adjust your speed to match road
conditions .
- Replace the fl at t ire wi th a new one and
have i t installed on your vehicle as soon as
possible to restore the hand ling advantages
of a un idirectional tire .
Notes on wheel changing
Please read the information¢ page 257, New
tires and replacing tires and wheels
if you a re
go ing to use a spare tire wh ich is different
from the tires on you r vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torqu e
checked with a torque wrench as soon a s
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims , the wheel
bolts are cor re ctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor­
roded and diff icult to turn while changing
a tire , they should be replaced before you
check the t ightening torque. .,,.
•
•

M N
0 I.J ""'. rl I.O
"' rl
"' rl
Technical data
Vehicle identification
F ig. 227 Veh ide Identificat ion Number (VlN) plate: lo ·
c ation on d river 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -IIOO -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JOZ 1LB lA S 18A
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 228
The vehicle identification label - inside the
luggage co mpartment
Vehicle Identification Number (VlN)
The Veh icle Identification Number is located
in different p laces :
- under the w indshield on the driver's side
¢fig. 227.
- in the MMI: Select: Function button ICAR ! >
(Car)* systems> Servicing & checks > VIN
number.
- on the vehicle identification label.
Techni cal data 289
Vehicle identification label
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
T he label¢
fig. 228 shows the following vehi­
cle data :
(D Vehicle Identificat ion Number (VIN)
@ Vehicle type, engine output, transmission
® Engine and transmission code
© Paint number and interior
® Optional equipment numbers
The information of the veh icle identification
label can also be found in your Warranty
&
Maintenance booklet .
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new veh icle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver's side. It shows the month and year of production
and the vehicle ident ification number of your
vehicle (perforation) as well as the Gross Vehi­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine hood release. The spark ignition system com­
plies with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
door jamb on the driver's s ide.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oil and coolant, plus maximum load, which in ­
cludes passenger we ight (150 lbs/68 kg per
II>--

306 Index
Saving fuel
Cylinder on d emand System .. .... .. .. 25
Efficiency program . . . . . . . . . . . . . . . . . . 26
Recuperation . . . . . . . . . . . . . . . . . . . . . . 25
Seat adjustment Controls . . . . . . . . . . . . . . . . . . . . . . . . . . S3
Driver's seat .............. ... .... .. 52
Front passenger's seat . . . . . . . . . . . . . . . 53
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 52
Head restraints . . . . . . . . . . . . . . . S5, 130
Safety guidelines .. ........ ... .. .. .. 52
Seat belts Why YOU MUST wear them
136
Seat covers
C leaning . .... ............. .. .... . 212
Seat heating/vent ilation (automatic cli ·
mate control) . . . . . . . . . . . . . . . . . . . . . . . 71
Seat heating (climate control) .. .. ...... 69
Seating position Driver ... .. ................ ..... . 127
Front passenger . . . . . . . . . . . . . . . . . . . 128
How to adjust the front seats ....... . 128
Incorrect seat position . . . . . . . . . . . . . . 130
Occupants .. .. . .......... .. .. .... . 127
Rear passengers . . . . . . . . . . . . . . . . . . . 129
Seat memory . . . . . . . . . . . . . . . . . . . . . . . 56
Seats Comfort seat side view .. .. .. .. .. .. . . 57
Seat symmetry ........... .. .. .. .. .. 57
Seats (number) ... .... ..... .. .. .. .. . 136
Selective catalytic reduction
refer to Ad Blue ............ ... .... . 218
Selective unlock feature ..... .... .... .. 34
Selector lever . . . . . . . . . . . . . . . . . . . . . . 107
Selecto r lever emergency release . . . . . . 113
Service and disposal Safety belt pretens ioner ... .. .. .... . 143
Service interval display ...... .. .. .... .. 27
Shift paddles ............... ... .... . 111
Ship (transporting your vehicle) ..... .. . 287
Shutting down vehicle ....... ... .. .. . 202
Side airbags Description .............. .. .. .. .. . 164
How they work ............ ... .... . 166
side assist . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Adjusting the brightness ... .. .. .. .. . . 98
Sensor range ............ .. .. .... .. 97 Side assist
Activating and deactivating ....... ... . 98
Cleaning the sensors ............ ... 210
S ide curtain airbags ............. .. .. 167
Description .... .. ............. .... 167
How they work ... ................ . 169
Safety instructions ............. .... 169
S ide marker lights . ... .......... .. .. . 43
Ski sack .. .. .. .. .. ............. .. .. . 65
Sliding/tilting sunroof Emergency closing ................ .. 41
Opening and closing ............ ... . 40
Snow cha ins .. .. . .. ............ .. .. 265
Socket . .... .... ................... . 59
Sources of information aboutchi ld re-
straints and their use ................ 189
Space-saving spare tire ........... .. .. 271
Spare tire . .. .... .. ............. .... 271
Speed limiter ..... ................ .. 30
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 2 7
Speed rating letter code .............. 260
Speed warning system ........... .. .. . 81
Sport differen tial .. ... .......... .. .. 100
Indicator light . .. ................ .. 23
Start-Stop-System ................. .. 79
Engine does not switched off .... .... . 80
Engine starts automatically ..... .... . 80
Indicator lights .. ............. .... . 79
Messages . ...... .. .............. .. 81
Start ing/stopp ing the engine .. .. .. .. . 79
switching off/on .. .... ...... ... .. .. . 81
START ENGINE STOP button ...... .. .. . 74
Starting from rest ... .............. .. . 78
Starting off with a trailer .......... ... . 78
Starting the engine ................ .. 74
Stee ring
Electrically adjustable steering wheel . . 73
Manua lly adjustable steering wheel ... . 73
also refer to Electromechanical power as-
sist ..... ..... .. .. .............. . 197
Steering wheel Easy entry feature ............. .... . 7 4
Indicator light . . . . . . . . . . . . . . . . 18, 197
Steering wheel heating .......... ... . 72