AUDI A6 2018 Owners Manual

a co ,...,
N
" N ,...,
0 0 \,;J ' Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correct tire pressure,
even if under-inf lation has not reached the level
to trigger illum ination of the TPMS low tire pres­
sure telltale .
Your veh icle has also been equ ipped w ith a TPMS
malfunct ion indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined w ith the low tire
pressure telltale. Whe n the system detects a
malfunct ion, the telltale will flash for approxi­
mately one minu te and then remain cont inuous ly
i llum inated. This sequence wi ll continue upon
subseq uen t veh icle start -ups as long as the ma l­
function exists.
When the malfunct ion i ndicator is ill uminated,
the system m ay not be ab le to detec t or sig nal
l ow tire press ure as intended. TPMS ma lfunctions
may occur for a var iety of reasons, incl uding the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the TPMS malfunction telltale after rep lacing one or
more t ires or whee ls on your vehicle to ensu re
that t he replacement or alternate ti res and
wheels allow the TPMS to cont inue to func tion
p roperly.
If the tire pressure monitoring system
indicator appears
A ppl ies to: ve hicles with Tire Pressure Moni toring System in­
di cato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Fig. 1 89 Instrument cl uste r: in dicator l ight w it h m essage
Wheels
Using the ABS sensors, the tire pressure monito r­
ing system compares the tire tread circumfer­
ence and vibration characterist ics of the ind ividu ­
al tires. If the pressure changes in one or more
t ires, th is is indicated in the instrument cluster
display with an indicator l ight
IE and a message .
If only o ne tire is affected, the location of tha t
t ir e will be indicated .
The tire pressures must be stored in the Infotain­ ment system again each time the pressures
change (switching between partial and full load
pressure) or afte r changing or replac ing a tire on
yo ur vehicle
Q page 220. The tire p ressure mon i­
tor ing system on ly mon itors the t ire pressure you
have stored. Refer to the t ire press ure label fo r
the recommended ti re pressure for yo ur vehicle
Q page 211, fig. 188 .
Tire tread c ircu mfe rence and vibr ation cha racter ­
istics can change and ca use a tire press ure warn­
ing if:
- the t ire pressure in one or more tires is too low
- the t ire has str uctural damage
- the t ire was replaced or the t ire pressure was
changed and it was not stored
Q page 220
- the spare tire* is i nstalled
Indicator light s
IE-toss of pressure in at least one tire Q & .
Check the tires and replace or repair if necessary .
Check/correct the pressures of all four tires and
store the pressu re again in the Infotainment sys­
tem
Q page 220.
m ( T ire Pressure Monitoring System) Ti re
pressure: System malfunction!.
If rn:m appears
after switching the ignition on or while driving
and the
IE indicator light in the instrument clus­
te r blinks for approx imately one minute and then
stays on, the re is system malf unct ion . Try to
store the co rrect t ire pressu res
Q page 220. If
t h e indicat or light does turn off or turns on agai n
af ter a sho rt pe riod o f time, d rive to an au thor­
ized Audi dea ler or authorized Audi Service Facili ­
ty immediate ly to have the ma lfunction correct-
ed.
~
219

Wheels
A WARNING
-If the t ire pressure indicator appears in the
display, reduce your speed immediate ly and
avoid any hard s teer ing or braking maneu­
vers . Stop as soon as possib le and check the
t ir es and thei r pressu re .
- The driver is responsib le for main taining the
correct tire pressure. You mus t check t he
t ir e pressure regu larly.
- Under certain conditions (such as a sporty
dr iv ing style, winter cond itions o r unpaved
ro ads), the tire p ressure mon itoring system
in dicator may be delaye d.
(D Tips
- The t ire pressu re monitoring sys tem can al­
so stop work ing when there is an ESC mal­
fun ct ion.
- Using snow chains may result in a system
malfu nction.
- The t ire pressu re monitoring sys tem in your
A udi was calibrated with "A udi Orig inal
T ires "~ page 208. Using these ti res is re c­
ommended.
Storing tire pressures
Applies to: vehicles with Tir e Pressure Monitor ing System in­
dicator
I f the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem .
.,. Make sur e before sto ring that t he tire pressures
of a ll fo ur t ires meet the specified val ues and
are ada pted to the load
c:;> page 211 .
.,. Switch the ign ition on .
.,. Se lect : the ICARI fu nction bu tton> ( Car )* Sys­
tems
con trol button > Service & control > Tire
pre ssure monitor > Store tire pre ssure > Yes,
store now .
(D Tips
Do not store the tire pre ssu res i f snow chains
are installed.
220

a co .... N
" N .... 0 0 \,;J ' Care and cleaning
General information
Regu lar, proper ca re helps to maintain your ve hi­
cle's value. It can a lso be a requirement when
submitting warranty claims fo r cor rosion damage
and pa int defects on the body.
The necessary care prod ucts can be obtained
from an authorized Audi dea le r or authorized
Aud i Service Facility . R ead and follow the instruc ­
tions fo r use on the packaging.
A WARNING
-Us ing clea ning and ca re products inco rrectly
can be dangero us to your hea lth .
- Always store clean ing and ca re prod ucts out
of reach of chi ldren to reduce the r isk of po i­
son ing .
@ For the sake of the environment
- P refe rab ly purchase env ironmenta lly-friend­
l y cleaning prod ucts.
- Do not d ispose o f leftove r clea ning and ca re
p roducts with house hold t rash.
Car washes
T he longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sun light
increase t he damag ing effect .
Before washing, rinse
off heavy deposits with
p lenty o f water.
S tu bbor n depos its s uch as bird droppi ngs or tree
sap are best removed with plenty of wate r and a
mic rofibe r cloth.
A lso , wash t he u nderside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washi ng your ve hicle w it h a pressu re wash­
e r, a lways fo llow the operating instr uctions pro­
v id ed wi th t he p ress ure washer. This is espe cially
i mportant in rega rd to the pressure and sp raying
d ista nce . Do not a im the spray directly at the
sea ls on the side w indows , doors, lids o r the sun -
Care and cleaning
roo f* or at tires, r ubber hoses, insulat ing mater i­
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm) .
D o no t remove snow and ice wi th a pressure
washe r.
Never use cone noz zles o r high press ure no zzles .
The water temperature must not be above 140 °F
(60 °() .
Automatic car washes
Spray of f th e vehicle befo re wash ing .
Make s ure that the w in d ows and roo f* are closed
and the windsh ie ld wipers are
off . Follow instruc ­
t ions from the car wash ope rato r, es pecially if
t h ere are accesso ries attac hed to you r vehicle .
If possible, use car washes th at do not have
brushes .
Washing by hand
Clean the ve hicle starting from t he top and wor k­
i ng down using a soft sponge o r clea ning br ush .
U se solven t-free cleani ng p rod ucts.
Washing vehicles with matte finish paint by
hand
To avo id d amag ing the pa int w hen washi ng, fi rst
r emove dust and large p articl es from you r vehi ­
cl e. Insects, gre ase spo ts and fingerpr ints are
best removed w it h a s pecial cleaner for mat te
finish paint.
Apply t he p rodu ct using a microfiber cloth. To
avo id dam ag ing t he pa int surfa ce, do no t use too
much pressure.
Rinse t he ve hicle thoroug hly w ith wate r. T hen
cl ea n usi ng a neutra l shampoo an d a soft m icro­
f iber clo th .
Rinse the ve hicle thoroug hly aga in and let it air
dry. Remove a ny wate r residue using a chamois .
A WARNING
- Only wash the veh icle w hen the ig nition is
off an d follow t he in str uctions from the car
wash ope rato r to re duce the ris k of acci ­
dents .
-
221

Care and cl eaning
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­ ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the braking effect
may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
c reases the risk of an acc ident. The brakes
must be d ried first w ith a few careful b rake
applica tions.
@ Note
- If you wash the veh icle in an automatic car
wash, you m ust fold the exte rior m irrors i n
to reduce the risk of damage to the mirrors.
Power folding exte rior m irro rs* must o nly
be fo lded in and out using the powe r folding
funct ion .
- To reduce t he risk of paint damage , do no t
wash the vehi cle i n direct sunlig ht. - T
o red uce the risk of damage to the s urface,
do not use insect removing sponges, kitchen
sponges o r similar items .
- Matte finish painted vehicle components:
- To reduce the r isk of damage to the sur-
face, do not use pol ish ing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
f inish paint. The paint could be damaged
when the stickers or magnets a re re­
moved.
@ For the sake of the environment
Only wash the veh icle in facilities spec ially de­
s igned for that pu rpose. This will reduce the
r isk of dirty wate r contam inated with o il from
en te ring the sewe r system.
Cleaning and care information
W hen clea ning and ca ring for ind ividua l vehicle
components, refer to the fo llow ing tables. The
information contained there is simply recom­
mendations. For questions or for components t
h at are not listed, cons ult an autho rized Audi
dealer or author ized A udi Servi ce Fac ility. Also
fo llow the information found
in ¢,&. .
Exterior cl eanin g
Component Situation Solution
Wind shield wiper
Deposits soft cloth with glass cleaner,
¢ page 45
blades
Headli ght s/
Deposits Soft sponge with a mild soap so lution3
)
Tail light s
S en sors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
cam era l ens es Camera lenses: soft cloth w ith alcohol -free cleaning solu-
tion
Snow/ice Hand brush/solvent-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
E
xhaust tail pip es Road salt Water, clean ing solution su itab le for stainless stee l, if nee-
essary
D ecor ativ e part s/ Deposits Mild soap solution a), a cleaning solution suitable for stain-
trim less steel, if necessary
222

a co .... N
" N .... 0 0 \,;J ' Care and cleaning
Component Situation Solution
P aint
Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint
c> page 245
Spilled fuel Rinse with water immediate ly
Surface rust Rust remover, then protect with hard wax; for questions,
consult an author ized Audi dealer or authorized Audi Serv-
i ce Facility .
Corrosion Have it removed by an authorized Audi dealer or author-
ized Audi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
pa int has been pro- the polish that was used does not contain any protectant
tected/pa int looks
poor
Deposits such as in- Dampen with water immediately and remove with a micro -
sects, bird droppings, fiber cloth
tree sap and road salt
Grease-based con- Remove immediately with a mild soap sol ution
al and a
taminants such as soft cloth
cosmetics or sunb lock
Carb on p art s Deposits clean the same way as painted parts c> page 221
a) Mild soap solution: max im um two tablespoons of neutral soap in 1 quar t (1 liter ) of water
Interior cl eaning
Component Situation Solution
Windo ws
Deposits Glass cleaner, then
wipe dry
Decor ati ve part s/ Deposits Mild soap solutional
trim
Pl as tic part s
Deposits Damp doth
H eavier depos its Mild soap solution
al, detergent-free plastic clean ing solu-
tion, if necessa ry
Di spl ays Deposits Soft cloth with LCD cleaner
Co ntro ls Deposits Soft brush, then a soft cloth with a mild soap solutional
Sa fe ty bel ts Deposits Mild soap sol ution al, allow to dry before letting them re-
tract
223

Care and cl eaning
Component Situation Solution
Tex tile s
Deposits adhering to Vacuum cleaner
art ifici al l eat her, the surface
A lca ntara Water -based deposits Absorbent cloth and mild soap solut
iona>
such as coffee, tea,
blood, etc.
O il-based deposits Apply a m ild soap solution
a), blot away the dissolved oil or
such as oil , make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain remover, blot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leathe r Fresh stains Cotton cloth
with a mild soap so lutiona >
Water-based deposits Fresh stairns : absorbent cloth
such as coffee, tea, Dried sta ins : stain remover suitable for leather
blood, etc.
Oil -based deposits Fresh stairns : absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remover suitab le for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Care Regula rly apply cond it ion ing cream that p rotects from
lig ht and penetrates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plastic parts
al Mild soap solution: maximum two tablespoons of neutral soap in 1 quart (1 liter) of water
_& WARNING
The windsh ie ld may not be treated wi th wa­
ter-repelling windshield coating agents. Un ­
favorable conditions such as wetness, dark ­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlight s/tail light s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form .
-Wheel s
224
- - Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Cam era lens es
- Neve r use wa rm or hot water to remove
snow or ice from the came ra lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning m aterials or
a lcohol to clean the camera lens . This
could cause scratches and cracks .
-Door wind ow s
- Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To

a co .... N
" N .... 0 0 \,;J ' avoid scratches, move the scraper only in
one direction and not back and forth.
- N ever remove snow or ice from door win­
dows and mirrors using warm or hot water
because this could cause cracks to form .
- To avoid damage to the rear w indow de ­
fogger, do not apply any stickers on the heating wires on the inside of the window .
-Deco rati ve parts /trim
- Never use chrome care or cleaning prod-
ucts.
- Paint
-To red uce the risk of scratches, the vehicle
must be free of dirt and dus t before pol­
ishing or waxing .
- To preven t pa int damage, do not pol ish or
wax the ve hicle in direct sunlight.
- To red uce the risk of pa int damage, do not
polish away rust spots.
- Remove cosmetics and sunscreen immedi­
a tely- these could damage the pa int.
- Displa ys
- To avoid scratches, do not use dry cleaning
methods on displays .
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause damage.
- Safet y belts
- Do not remove the safety belts to clean
t hem.
- Never clean safety belts or their compo­
nents chemically or with cor rosive fl uids
or so lvents and neve r allow sh arp obje cts
t o come into con ta ct w ith the sa fe ty belts.
Th is could cause damage to the belt web ­
bing .
- If the re is damage to the webbing, the
connections, the retractors or the b uckles,
have them replaced by an authorized Audi
dea ler or authorized Audi Service Facility.
- Te xtiles/artificial leather / Alcantara
- Never treat artific ial leather/ Alcantara
w ith leather care products, solvents, floor
polish, shoe polish, spot remove or similar
prod ucts .
- Have a specialist remove st ubborn stains
to prevent damage.
Care and cleaning
- Neve r use steam cleaners, brushes, hard
sponges, etc. when cleaning .
- Do not turn on the seat heating* to dry the
seat.
- Obje cts w ith sharp edges, such as zippe rs
or rivets on clothing or be lts, can cause
damage to the surface .
- Open hoo k and loop fasteners, for exam­
p le on clothing, can damage seat covers.
M ake sure hook and loop fasteners are
closed.
- Natural leather
- Never treat leather with solvents, floor
polish, shoe po lish, spot remover or sim i­
lar p roducts.
- Objects w ith sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the seat.
- To he lp prevent the leather from fad ing,
do not leave the vehicle in direct sun light
fo r long pe riods of time. If leav ing the ve­
h icle parked fo r long pe riods of time, you
should cover the le athe r to prote ct it from
d irec t sun light.
(D Tips
- Insects are easie r to remove from paint that
has been freshly waxed.
- Regular wax ing can prevent rust spots from
forming.
Placing your vehicle out
of service
If you would like to take your vehicle out of serv ­
ice for a longer period of time, contact an author­
ized Audi dea ler or authorized Audi Service Facili ­
ty. They will adv ise you of important measures,
such as corrosion protection, service and storage
procedures. Also follow the information about
the veh icle battery
r=;,page 197 .
225

Emergency assistance
Emergency assistance
General information
.,. Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
.,. Set up the warning triangle r=;,page 226 .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
A pplies to: ve hicles w ith warning triangle
Fig. 190 Luggage compa rtment lid : wa rnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.,. To remove the warning triangle, press the re-
tainer in the direction of the arrow
r:;, fig . 190
and fold the holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
226
Vehicle tool kit
Fig. 191 Luggage compartment: vehicle tool kit
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover.
.,. Lift the cargo floor by the plastic handle.
.,. Hook the handle into the luggage compartment
weather strip.
.,. Turn the handle counter-clockwise and remove
the cover or the spare tire* .
.,. Unhook the cargo floor before clos ing the lug­
gage compartment lid.
A WARNING
I mproper use of the veh icle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­
stances should it be used to lift heavy
vehicles or other loads; you risk injuring
yourself.
- Never start the engine when the vehicle is
raised, which could cause an accident .
- Support the vehicle securely with appropri­ ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury .
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
vehicle it came with.

a co .... N
" N .... 0 0 \.J ' (D Tips
The vehicle jack* in your vehicle is mainte­
na nee-free.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel .
'"After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
le ve l ground before you stop ¢,&. .
'"All passe ngers should le ave the car and move
to a safe location (for instance, be hind the
guardra il) ¢ ,&. .
.. Engage the parkin g brake to p revent your vehi ­
cle from rolling
unintentionally ¢,&. .
'"Move selecto r lev er to p osition P ¢ ,&. .
'"If you are towing a trailer, unh itch the trailer
from your veh icle.
'" Take the jac k and the sp are tir e* out of the lug­
gage compartment
i::> page 226 .
A WARNING
You or your passengers cou ld be inju red w hile
chang ing a wheel if you do not follow these
safety precautions :
- If you have a flat t ire, move a safe distance
off t he road. Tur n off the engine, t urn the
emergency flashers on and use other warn ­
ing devices to alert other motorists .
- Make s ure tha t pa ssengers w ait in a sa fe
place away from the vehicle and we ll away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping o ff th e jack,
always fully set the parking brake and b lock
the front and back of the wheel diagonally opposite the wheel be ing changed. When
one front whee l is lifted off the ground,
placing the Automatic Transm ission in P
(Park) w ill
not prevent the veh icle from
moving.
Em ergenc y ass is tanc e
-Before you change a whee l, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 130.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
tro ls for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the
jack ¢ page 229 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-step and in exactly that
order .
l. Activate the vehicle jack mode* ¢ page 229.
2. Remove the deco rati ve wheel co ver* or the
wheel bolt c aps *. For more details see also
¢ page 228, Decorative wheel covers or
¢ page 228, Wheels with wheel bolt caps .
3. Loosen the wheel bolt s ¢page 229.
4. Locate t he p roper mount ing point for the
jack and align the jack be low that poin t
¢page 229 .
S. R ais e the car with the jack ¢ page 229 .
6. Remove the wheel with the fl at tir e and then
install
the spare ¢ page 231.
7. Tig hte n all wheel bolts lightly .
8 .
Lower the vehicle with the jack .
9 . Use the wheel bolt wrench and
firml y tighten
all wheel
bo lts ¢ page 229.
10. Replace t he decorat ive wh eel cover * or the
wheel bolt cap s*.
11. Deactivate the vehicle jack mode* in t he
MMI :
ICAR I function button > (Car )* sys tem s
contro l button > Ser vicing & che cks > Air
s usp.: jack mod e> Off.
The vehicle jack mode * switches off automatica l-
ly at speeds abov e 6 mph (10 km/h).
.,.
227

Emergency assistance
A WARNING
Always read and follow all WARNINGS and in­
formation
c:> & in Raising the vehicle on
page 230
and c:> page 232.
After changing a wheel
A wheel change is not complete without the do­
ing the following .
.. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
c:> page 130 .
.. Check the tire pressure on the spare wheel im­
med iate ly after mount ing it .
.. As soon as possible, have the tightening tor­
ques
on all wheel bolts checked with a torque
wrench. The correct tightening torque is 90 ft
lb s (120 Nm) .
.. Have the flat tire replaced as soon as possible.
@ Tips
-If you notice that the wheel bolts are cor­
roded and difficu lt to turn while changing a
tire, they should be replaced before you
check the tightening torque.
-Drive at reduced speed until you have the
tightening torques checked.
-After changing a wheel, the tire pressure in
a ll four tires must be checked/corrected and
the tire pressure monitoring indicator must
be stored in the MMI
<=> page 220.
Decorative wheel covers
App lies to: vehicl es w ith decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 192 Changing a wheel: Remov in g the whee l cove r
228
Removing
.,. Insert the hook (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
.. Pull off the decorative wheel cover c:> fig. 192 .
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed .
Fig. 193 C hanging a wheel: remov ing the w heel bolt caps
Removing
.,. Push the plastic clip (provided with the vehicle
tool kit) over the whee l bolt cap until the inner
reta iners on the clip align with the edge of the
cover.
.. Remove the cap with the plastic clip (vehicle
tool kit)
c:> fig. 193.
Refitting
.,. Place the caps over the whee l bolts and push
them back on.
The caps are to protect and keep the wheel bo lts
clean.