change wheel AUDI A7 2013 Owner's Manual

26 6 T ire s and whee ls
check the tires and their pressures. In­
flate the tire pressure to the proper pres­
sure as indicated on the vehicle's tire
pressure label
c> page 250. Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to impair the vehicle's handling and stop­
ping ability.
- T he driver is responsible for ma inta ining
the correct tire pressures. You must check the t ire pressures regular ly .
- Under certain cond itions (such as a spor­
ty driving style, winter condit ions or un­
paved roads), the pressure monitor indi­
cator may be de layed .
- Ask your author ized Audi dealer if r un­
flat tires may be used on your vehicle .
Your vehicle regist ration becomes invalid
if yo u use these tires when not permit­
ted. Damage to your veh icle or accidents
cou ld also result.
- The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction .
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with
the "AO" or "RO" identif ication on the
tire sidewall
c> page 257. We recom­
mend using these t ires.
Reset tire pressure monitoring system
App lies to vehicles: with tire pressure monito ring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
MMI.
., Switch on the ignition .
., Se lect in the MMI: !CAR !function button>
(C ar)* s ystems contro l butto n > Se rvicing &
checks > Tire pre ssure mon itoring > Store
tire pr essures> Ye s, store n ow .
(D Tips
Do not store the tire pressure if there are
snow cha ins on the tire .

Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fai lure, pull the
car well away from moving traffic and try to
reach
le vel gro und before you stop¢.&_ .
.. All passengers shou ld
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il)¢ .&_.
.. Engage the
parking br ake to prevent your
vehicle from ro lling unintentionally¢ .&_.
.. Move
selecto r leve r to posi tion P ¢ .&_ .
.. If you are tow ing a trai ler, unh itch the trai l­
er from your veh icle.
.,. Take the
jack and the spare tire out of the
luggage compartment ¢
page 267,
¢page 268.
.8, WARNING
You or your passengers cou ld be injured
w hile changing a whee l if yo u do not fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis ­
t a nce off the ro ad. Tur n off the eng ine,
turn the emergency f lashers on an d use
other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the ve hicle and well
away from the road and traff ic.
- To help p revent the vehicle from moving
sudden ly and possibly slipping off the
jack, always fu lly set the parking brake
and block the wheel diagonally opposite
the wheel being changed. Whe n one
front wheel is lifted off the ground, plac­ ing the A utomat ic Transm iss ion in P
(Park) will
not p revent the vehicle from
moving.
- Before you change a wheel, be su re the
ground is level and fi rm. If necessa ry,
use a sturdy board under the jack.
-
What do I do now? 269
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­ partment
¢page 136.
(D Tips
Before changing the whee l, you must acti­
vate the jacking mode, so that the auto­ matic controls for the Adaptive Air Sus­
pension* do not make it more d iff icult to
lift the vehicle with the jack
¢ page 271 .
Changing a wheel
When you change a wheel , follow these­
quence described below step-by-step and in
exactly that order .
l. Activate the vehicle jack mode*
¢page 271 .
2. Remove the decorativ e whee l cover* . For
more details see also¢
page 2 70, Deco­
rative wheel covers
or ¢ page 2 70,
Wheels with wheel bolt caps .
3. Loosen the wh eel bolt s ¢page 271.
4. Loca te the p roper moun ting poin t for the
jack and align the jack be low that point
¢ page 271 .
5. Rais e the car with the jack ¢ page 271.
6. Remove the wheel with the flat tire and
then install
the spare ¢page 273.
7. Tighten all whee l bolts lightly .
8.
Lo wer the vehicle with the jack .
9 . Use the wheel bolt w rench and
firmly
t ighten al l wheel bolts¢ page 2 71.
10. Rep lace the deco ra ti ve whe el c ove r*.
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI f u nction button > (Car )* sy s­
tems
contro l button > S ervici ng & check s
> Air s usp.: jack mod e > Off.
The vehicle jack mode * switches off automati­
ca lly at speeds above 6 mph (10 km/h) .
.8, WARNING
-Always read and fo llow all WARNINGS and
i nformat ion¢
A in Raising the vehicle on
page
272 and ¢ page 274.
•
•

2 70 What do I do now ?
After changing a wheel
A wheel change is not complete without the
doing the following .
.. Always store the vehicle too l kit, the jack*
and the replaced ti re i n the luggage com­
partment ¢
page 136.
.. Check the tire pres sure on the spare w heel
i m media tely after mount ing it .
.,. As soo n as po ssible, have the
tightening
torques
on a ll w heel bol ts checked with a
tor que wrench . The correct tightening tor ­
que is 90 ft lb ( 120 Nm) .
.. Have the flat tire
replaced as soon as poss i­
ble.
@ Tips
- If you notice t hat the whee l bolts are
corroded and difficult to t urn while
changing a t ire, they should be replaced
bef ore yo u check the tighten ing torque .
- Drive at reduced speed unt il y ou have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n a ll four tires must be checked/cor rect­
ed and t he tire pressure mo nitor ing indi­
cator must be stored in the MMI
¢page 266 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
T he decora tive wh eel covers must be removed
first to access the wheel bolts .
Fig. 206 Changing a w hee l: Re movin g the w heel cove r
Removing
.,. Inse rt the hook (provided with the ve hicle
tool kit ) in t he hole in the wheel hub cove r. ..
Pull off the
decorative wheel cover
¢fig . 206.
Wheels with wheel bolt caps
Applies to veh icles: w it h w heel bolts with caps
The ca ps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig . 20 7 Cha ng ing a w heel: re m oving t he w hee l b o lt
caps
Removing
.. Push t he plastic clip (provided with the ve­
hicle tool kit) over t he wheel bolt cap u nti l
the inner reta iners on the clip a lign with the
edge of the cover.
.,. Remove the cap wit h the
plastic clip (veh i­
cle tool kit)
¢ fig . 207 .
Refitting
.. Place the caps over the whee l bolts and
push them back o n.
The caps are to protect and keep the wheel bo lts clean .

Loosening and tightening the wheel
bolt s
The wheel bolts must be loosened before rais­
ing the vehicle.
F ig. 208 Changing a whee l: loos enin g the wh eel bo lt s
Loo sening
.. Slide the whe el w re nch onto the wheel bolt
as far as it wi ll go .
.. Take tight hold of th e
end of the wrench
hand le and turn the whee l bolts
counte r­
clock wis e
abou t one single turn in the direc­
tion of arrow c:>
fig. 208 .
Tightening
.. Slide the wheel wrench onto the whee l bolt
as far as it will go.
.. Take tigh t hold of the
end of the wrench
handle and turn each wheel bolt
cl ockw ise
unt il it is seated .
A WARNING
-Do not use force or hurry when changing
a whee l -you can cause the vehicle to s lip
off the jack and cause ser ious persona l
injuries.
- Do not loosen the wheel bolts more than
one turn
before you ra ise the veh icle w ith
the jack. -You risk an injury.
(D Tips
- Never use the hexagonal socket in the
handle of the screwd rive r to loosen or
tighten the wheel bo lts.
- If a whee l bolt is very tight, you may find
i t easier to loosen by c arefully p ushi ng
down on the end of the whee l bolt
wrench with
one foot only . As you do so,
What do I d o now ? 271
hold on to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with th e jack first
before the wheel can be removed.
F ig . 209 Sill panels : ma rki ngs
Fig . 210 Sill : p os it ion ing t he ve hicle jack
.. Act iv ate the vehicle jack mode* in the MMI:
!CAR I function button> (Car) * sy stems con­
trol button>
S e rv icing & ch ecks > Air su sp .:
jack mode > On .
.,. Engage the park ing brake to prevent your
veh icle from rolling unintentionally .
.,. Move the
s elect or le ver to p osition P .
.,. Find the marking (imp rint) on the sill tha t
is nearest the wheel that wi ll be changed
r=> fig. 209 . Behind the marking, there is a
lifti ng p oint on the sill for the veh icle jack .
.. Veh icles wi th a s ill: remove the cover from
the sill before lift ing the veh icle wi th a vehi­
cle jack
c:> page 272 .
.,. Turn the vehicl e ja ck located under the lift­
ing point on the sill to ra ise the jack unti l its
arm @ c:>
fig. 210 is located under the des­
ignated p lastic moun t c:> &, c:>(D .
.. Align the jack so that its arm@c:>
fig. 210
engages in the designated lifting point in
the door sill and the movable base @ lies
~

272 What do I do n ow ?
flat on the ground. The base @ must be ve r­
tical under the lifting point @.
• Wind the jack up further until the flat tire
comes
off the ground <=>,& .
Position the vehicle jack
onl y under the desig­
nated lifting points on the sill~
fig. 209.
There is exactly one location for each wheel.
The jack must not be positioned at any other
locat ion <=> .&. <=>CD.
An
u ns table su rf ac e under the jack can cause
the vehicle to slip off the jack. Always provide
a firm base for the jack on the ground. If nec­
essary place a sturdy board or s imilar support
under the jack. On
h ard , s lipp ery su rf ac es
(such as tiles) use a r ubber mat or sim ilar to
prevent the jack from slipping ~,&. .
.&, WARNING
-You or your passengers could be injured
wh ile chang ing a whee l if yo u do not fol­
low these safety precautions:
- Position the vehicle jack only at the
des ignated lifting points and align the
jack . Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient ho ld on the vehicle.
- A soft or unstable surface under the
jack may ca use the vehicle to slip off
the jack. Always provide a fi rm base for
t he jack on the ground. If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or s imilar to prevent
the jack from slipping.
- T o help p revent injury to yourself and
your passenge rs:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not rema in in the ve­
h icle when it is jacked up.
- Make sure that passengers wait in a safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­ just as necessary and then continue to ra ise the jack. -
Changes in temperature or load can af­
fect the he ight of the vehicle .
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­ ing po ints on the sill. Otherwise, your vehi­
cle will be damaged .
(D Tips
The vehicle jack mode* switches off auto­
matically at speeds above 6 mph (10 km/
h).
Removing and installing the s ill cover
Applies to vehicles: wit h sill
Fig . 2 1 1 S ill: r emoving the cov er
,.. Pull the cover down to remove it ~fig. 211.
• To insta ll the cover again, insert it into the
retainers and t hen swing it upward until it
clicks into p lace. The cover must be flush
w ith the sill.
@ Tips
Some models may also have a cover for the
rear vehicle lift po int.

Data
Data
A7 Sportback 310 hp., 3.Q, liter 6-cylinder engine
Applies to vehicles: with 3.0 liter 6-cyli nde r engine and all-wheel d rive
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dimensions (approx .)
L eng th (wit h license pl ate brac ket)
Width (across mirrors) He igh t (unloaded) hp@
rpm
lb-ft@ rpm
C ID (cm
3
)
in (mm)
in (mm)
-- ,
__ ...
310@ 5500-6500
325 @ 2900-4500
6
182 (2995)
3.50 (89 .0)
3 .33 (8 4.5)
10 .3 : 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details
Qpage 225,
Gasoline
in (mm) 1 95.6 ( 4969)
in (mm) 84.2 (2139)
in (mm) 55.9 (1 420)
Turning circle diameter (curb to curb) ft. (m) 39. 0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capacity
- Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight washer
fluid container *
Engine oil
with filter change gal (liters)
19.8 (75.0)
g
al (li ters) 2. 6 (10.0)
quarts (liters) 3.7 (3.5)
qu arts ( liters) 5 .2 ( 4.9)
quarts (lite rs) 7.2 (6.8)
287
•
•

300 Index
K
Key ... . ... ....... ......... ... .... .. 32
Battery replacement master key ... .. .. 33
Emergency key .............. ..... .. 32
Key not recognized . . . . . . . . . . . . . . . . . . 78
Key replacement ......... .... .... .. 32
Master key . . . . . . . . . . . . . . . . . . . . . . . . 32
Mechanical key .............. ... ... . 33
Valet key . .. .. ........ .... ... .. .. .. 32
Kick-down tiptronic
113
Knee airbags ................. ..... . 166
Description ................. ..... . 166
How they work .............. ..... . 168
Important safety instructions . . . . . . . . 168
L
Lane assist . . . . . . . . . . . . . . . . . . . . . . . . . 95
Lane Change Assistant
refer to side assist . . . . . . . . . . . . . . . . . . 98
LATCH .. .. .. ............. .... .. ... 189
Descript ion .... .... ...... .. .. .. .. .
Installing a child restraint ...... .. .. .
Location .. .... ............. ... ' . .
Mounting and releasing the anchorage
hook
. . .. .. ............. .... .. .. .
190
191
190
191
Launch Control Program .... .. .. .. .. . 114
Leather ..................... ..... . 221
L eather (cleaning) .......... .. .. .. .. . 222
Leaving home ............. .. .. .. .. .. 45
Lifting jack . . . . . . . . . . . . . . . . . . . . . . . . 2 71
Lifting vehicle ................ ... ... 283
Light Ambience lighting .......... .. .... .. 46
Coming/Leaving home ..... .. .. ...... 45
Daytime running lights .. ... ... .. .. .. 43
Emergency flashers . . . . . . . . . . . . . . . . . 44
Exterior lighting .... .. .... .. .. .. .. ..
43
H ead light range control ... .. .. .. .. . . 43
High beam .............. ........ .. 45
L ow beam . ................. ..... ..
43
Rear fog lights .............. ..... .. 43
Side marker lights ......... ... .... ..
43
Turn signals ............. .. .. .. .. .. 45 Light/rain
sensor
Headlights . ..... ................ .. 43
Intermittent (windshield w ipers) ...... 47
Sensor defective . . . . . . . . . . . . . . . . . . . . 22
Loading the roof rack ................ . 62
Locking Power locking switch ................ 37
Remote control .... ........... .. .. . 35
Using the key ................. ..... 37
Low beams . .... .. ... .......... .... . 43
Lower universal anchorages (Canada) . . .
189
Luggage compartment
Bag hooks . . . . . . . . . . . . . . . . . . . . . . . . . 65
Cargo net . . . . . . . . . . . . . . . . . . . . . . . . . 65
carpeting ..... .. ................ .. 66
Cover ......... .. ..................
63
Enlarging . . . . . . . . . . . . . . . . . . . . . . . . . 64
Loading ... ...... ................. .
63
Ski sack ...................... ..... 66
Stowing luggage .............. ....
136
Tie -downs . . . . . . . . . . . . . . . . . . . . . . . . . 65
Trunk pass-through ...... ...... .. .. . 67
Lumbar support
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 54
M
Maintenance .... .. ................ . 289
Malfunction Indicator Lamp (MIL) . . 21, 29
Manual shift program ............ .. .. 113
Massage function
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 54
Matte finish paint .. ............. .. .. 215
Mechanical key .. .. ... .......... .. .. . 33
Mirrors Adjusting the exterior mirrors ..... ... .
49
d' . ,mmrng .. .... .. ................ .. so
Vanity mirrors ................ ..... 47
Monitoring the Advanced Airbag System
161
Multifunction steering wheel .. .. .. .. .. . 25
N
Natural leather .....................
New t ires and wheels
NHTSA 221
257
Contacting .. .. .. ....... ...... .. .. 138