TPMS reset AUDI A7 2015 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: A7, Model: AUDI A7 2015Pages: 316, PDF Size: 78.09 MB
Page 273 of 316

M N <( I.J "". rl I.O 
"' rl 
"' rl 
Tire  pressure indicator  appears 
The tire  pressure  indicator  in  the  instrument 
cluster  informs  you  if  the  tire  pressure  is too 
low  or  if  there  is a system  malfunction. 
Fig.  205 Display: underinflation  warning 
Fig. 206 Display:  System malfunction 
Using the ABS sensors, the  tire pressure  moni
toring  system  compares the  tire  tread  circum ference  and vibration  characteristics  of  the  in
dividual  tires.  If  the  pressure  decreases in  one 
or  more  tires,  this  is indicated  in the  instru
ment  cluster  with a warning  symbol 
rD] and a 
message 
c:> fig . 205. 
The tire  pressure  monitoring  system  must  be 
reset  via  MMI  each time  the  pressures  are ad
justed  (e.g.  when  switching  between  partial 
and fu ll load  pressure)  or  after  changing  or  re
placing  a tire  on your  vehicle 
c:> page272 . The 
TPMS  indicator  only  monitors  the  tire  pres
sure  that you  have previously  stored.  You can 
find  the  recommended  tire  pressures for  your 
vehicle  on the  label on  driver's  side 8-pillar 
c:>page247. 
Tire tread  circumference  and vibration  charac
teristics  can change and  cause a tire  pressure 
warning  if: 
- the  tire  pressure  in one or  more  tires  is too 
low, 
Tires  and  wheels  2 71 
- the  tire  has structural  damage, 
- the  tire  pressure was changed,  wheels  rotat-
ed or  replaced  but  the  TPMS was not  reset 
c:>poge272. 
- the  spare tire*  is mounted . 
Warning  symbols 
[I] Loss of  pressure in at  least  one tire¢.& . 
Check the  tire  or  tires  and  replace or  repair  if 
necessary.  The indicator  light 
rD] in the  instru
ment  cluster  also illuminates <=:> 
page  12. 
Check/correct  the pressures of  all  four  tires 
and  resetTPMS  via  MMI. 
l!I (Tire  Pressure Mon itoring System) Tire 
pressure!  System  malfunction . 
Ifljl appears 
after  switching  the  ignition  on or  while  driving 
¢ 
fig.  206 and  the indicator  light rD] in the  in
strument  cluster  blinks  for  approximately  one 
minute  and then  stays  on, there  is a  system 
malfunction.  Attempt  to  store  the correct tire 
pressure 
c:> page  272. If the  indicator  light 
does not  turn  off  or  if  it turns  on  shortly 
thereafter,  immediately drive your  vehicle  to 
an authorized  Audi  dealer  or  authorized  repair 
facility  to  have  the malfunction  corrected. 
_& WARNING 
- If the tire  pressure  indicator  appears in 
the  instrument  cluster  display,  one  or 
more  of  your  tires  is significantly  under
inflated.  Reduce your  speed  immediately 
and avoid  any hard  steering  or  braking 
maneuvers.  Stop  as soon  as possible  and 
check the  tires and their  pressures.  In
flate  the  tire  pressure  to  the  proper  pres
sure as  indicated  on the  vehicle's  tire 
pressure  label<=:> 
page  247 . Driving  on  a 
significantly  under-inflated  tire  causes 
the  tire  to  overheat  and can lead  to  tire 
failure.  Under-inflation  also is likely  to 
impair  the  vehicle's  handling  and stop
ping  ability. 
- The driver  is responsible  for  maintaining 
the  correct  tire  pressures. You must  check the  tire  pressures regularly. 
.  
Page 274 of 316

272  Tires  and  wheels -Under certain  conditions  (such as a spor
ty  driving  style,  winter  conditions  or un
paved roads),  the  pressure monitor 
indicator  may be delayed. 
- Ask your  authorized  Audi  dealer  if  run
flat  tires  may be used on your  vehicle. 
- The tire  pressure  monitoring  system  may 
stop  working  when  there  is an  ESC mal
function. 
- Using snow chains may  result  in a system 
malfunction. 
- The tire  pressure  monitoring  system  on 
your  Audi  was developed  using tires  with 
the  "AO"  or "RO"  identification  on the 
tire  sidewall 
c:> page  260.  We recom
mend  using  these tires. 
Reset  tire  pressure  monitoring  system 
If  the  tire  pressure  is adjusted,  wheels  are  ro
tated  or  changed,  the  TPMS must  be reset  via 
MMI. 
•  Before storing  the  new tire  pressures, check 
that  the  current  pressures on all  four  tires  correspond  to  the  specified  values and 
adapt  the  pressures to  the  current  load  <=>page  247. 
•  Switch  on  the  ignition. 
•  Select in the  MMI:  !CAR !function  button> 
(Car)* systems control  button > Servicing & 
checks  > Tire  pressure monitoring  > Store 
tire  pressures>  Yes, store  now. 
Do  not  store  the  tire pressure if  there  are 
snow chains on the  tire.  Otherwise, a sys
tem  malfunction  may  occur.