engine AUDI A7 2016 Manual Online

Fuses
Driver side cockpit fuse
assignment
Fig. 212 Driver's side of the cockpit : fuse pa nel w it h plastic
cl ip
Fuse panel @ (black)
No. Equipment
Electromechanical power steer ing, trailer
1 hitch, ionizer, switch strip, seat heating
(rear), electromechanica l park ing brake
Horn, climate control system, Gateway,
2 automatic dimming interior rearview mir-
ror
4 Parking aid, headlight range adjustment
5 Dynamic steering, Electronic Stabilization
Control (ESC)
6 Headlights
7 Adaptive cru
ise control
8 Front passenger's seat sensors, airbag
9 Gateway
10 E
ngine sound, night vision assist, garage
door opener (Homelink), parking aid
11 Video camera image processing
12 Headlights
13 Steering col umn switch module
14 Terminal 15 (luggage compartment)
262
Fuse panel @ (black)
15 Terminal 15 (engine compartment)
16 Starter
Fuse panel @ (brown)
No . Equipment
1 Infotainment
2 Infotainment
3 Front passenger
's seat
5 Airbag, Electron
ic Stabilization Control
(ESC)
6 Anti -theft alarm system
7 Electromechanical parking brake
8 Inter
ior lights
9 Windshie
ld video camera heating , light/
rain sensor
10 Lumbar support (driver's seat)
11 Driver's seat
12 Electronic stabilization control
13 Horn
14 Headlights
15 Front seat heating
16 Dynamic steering
Fuse panel © (red)
No. Equipment
1 Clutch pedal
2 Fuel pump
3 Brake light sensor
4 AdBlue (diesel engine)/engine acoustics
5 Rear door
6 Front
door
7 Electronic stabilization control
8 Windshield wiper motor
9 Headlight washer system
10 Interior lighting, climate control system
11 Headlights
12 Sunroof

M N <( I.J "". rl I.O
"' N I.O rl
Front passenger side
cockpit fuse assignment
F ig. 21 3 Front passenger 's s ide of t he cockp it fuse pa nel
wit h plast ic cl ip
Fuse panel @ (red)
No. Equipment
1 Infotainment, CD changer
2 I nfotain ment (d isplay)
Fuse panel @ (brown)
No . Equipment
1 Climate control system
2 Climate con
trol sys tem (blower)
3 Diagnostic interface
4 Ele ctric al ignit ion loc k
5 Electro nic steer ing colum n lock
6 Steer ing column sw itch modu le
7 Power steering co lumn adjustment
8 Light switch
9 Head-up display
1 0 I
nstrument cluste r
1 1 Infotainment, DVD changer
Fuses
Luggage compartment
fuse assignment
F ig . 214 Lu ggage compa rtm ent: fuse pa nel w ith plastic
cli p
Fuse panel @ (black)
No. Equipment
1 Trailer h
itch/220 vo lt socket
2 Trailer h itch/ climatize d cup holder
3
Trailer h itch/adjusting front passenger's
seat from the rear
4 El ec tromech anical p ar kin g bra ke
5 Electromecha nica l park ing brake
6 Fr ont door (front passenger 's side)
7 Rear exterior lig hti ng
8 Cent ral loc king, closing aid
9 Seat heating (front)
1 1 Seat heating (rear), climate control system
12 Trailer h itch
Fuse panel @ (r ed)
No. Equipment
1 L
eft safety be lt tensioner
2 R ight safety be lt tensione r
3 AdBlue tank (diesel engine)/f uel p ump
4 Ad B lue tank (diese l engi ne)/engine mount
(g asol ine engine)
s
Sensor -co ntrolled luggage compartment
li d
6 Air s uspension, adaptive dam pers
7 Rear door (fro nt passenge r's side)
8 Tail lig hts
9 Luggage compartment lid
263

Fuses
Fuse panel® (red)
10 Rear seat entertainment
12
Rear spoiler (Sportback), tilt/open sunroof,
Panorama g lass roof
Fuse panel © (brown)
No. Equipment
1 Infotainment
2 I n fota inment
3
Infotainment , automatic d imm ing interior
rea rview mirro r
s TV tuner
6 Tank leak detection system
7 Sockets
8 Park ing heate r
10 Lu mba r su pport (front passenger's seat)
12 Infota inment
Fuse panel @ (black )
No. Equipm ent
Air suspens io n, adapt ive dampers, sport
l differentia l, e lectr om echanical parking
brake
2
Clu tch pedal position senso r/au tomatic
transmission
3 Seats
4 Rear w iper (Avant)
s Side assist
6 Engine sound
7 Infota inment/sound amplifier
8 Gateway
9 Sport differentia l
10 Climate control system
11
T ire press ure moni to ring sys tem/p ark ing
heater
12 Start-Stop-System
Fuse panel © (black )
No. Equipment
1 Special p urpose vehicles/rear seats
Fuse panel ® (black)
No. Equipment
1 Rear w indow defogge r
264

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform the se
operations.
Starting by pushing or
towing
(D Note
Vehicles w ith an automatic transmission can­
not be started by push ing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because o f a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, us ing a
pair of jumper cables to start the engine .
Jumper cables
Use only jumper cables of sufficiently large cros s
section
to carry the starter current safe ly. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated term inal
clamps which are distinctly marked:
plus(+) cable in most cases co lored red
minus (-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas .
Any of these can cause very ser ious or fatal in­
jury . Fo llow the instructions be low for safe
handling of your vehicle's battery.
- Always shield your eyes and avoid leaning
over the battery whenever possible.
- A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C) . Before con­
necting a jumper cable, you must thaw the
Emergency situations
frozen battery completely, otherwise it
could explode .
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
veh icle may cause an explosion.
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must al ­
so have a 12-volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of batteries of different voltage or substantial­
ly different" Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery . Gas trapped
in the ice may cause an explosion .
- Never charge or use a battery that has been
frozen . The battery case may have be weak­
ened ,
- Use of batter ies of different voltage or sub­
stantially different capacity (Ah) rating may
cause an exp losion and injury. Th e capacity
(Ah) of the booste r battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
q page 218 .
(D Note
-Applying a h igher voltage booster battery
w ill cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- Th ere must be no ele ct rical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) termina ls are connected.
(D Tips
The discharged battery must be properly con-
nected to the vehicle's e lectrical system. .,..
265

Emergency situation s
When jump sta rting or charging the battery,
never connect the negative ground cable to
the batte ry negat ive post because the battery
manager system must be able to detect the
battery's state of c harge. Always connect the
negat ive grou nd cab le to the negative ground
post of the batte ry manager control unit .
Use of jumper cables
Make sure to connect the jumper cable clamps in
ex actly the order described below!
F ig . 215 Eng ine co m pa rt m ent: con nec tors for ju mp star t
cab les a nd cha rge r

® .--l @
Fig . 2 16 Jum p start ing w it h t he bat te ry of a not her ve hicl e:
@-boos te r ba ttery , @ -disc harg ed v eh icle batt ery
The procedure described be low for con necting
jumper cables is intended to p rovide a jump start
for your ve hicle.
Vehicle with discharged battery: •T urnoff lig ht s and accesso ries , move lever of
automat ic transmiss ion to N (Ne utra l) or P
(Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+) (red)
• Open the red cove r o n t he po sit ive termin al
~fig . 2 15.
266
1. Connect one end o f the red positive ca ble on
the
jump start bolt ~ fig. 216 /J) (bolt under
the red cover = "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi-
nal@ of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black )
3. Co nnect one end of the black negative cable
to the negative term inal ® of the booste r
batte ry @ .
4 . Connect th e other end to the
jump start pin
@ (bolts w it h hex head bolt = "negative") of
the veh icle to be s tarte d@ .
Starting the engine • Sta rt the engine of the veh icle with the booster
bat tery @. Run the eng ine at a moderate
speed.
• Sta rt engine w it h discha rged vehicle ba ttery @
i n t he usual man ner.
• If the engine fails to start, do not keep the
starter cra nking for lo nger than 10 seco nds .
Wait for about 30 seconds and then try again .
• With engine running , remove jumper cab les
from both vehicles in the exact
reverse order .
• Close the red cover on the positive term inal.
The batt ery is vented to the o utside to prevent
gases from enter ing the vehicle inter ior. Make
su re that t he jumper clamps are well connected
with their metal parts in full contact w ith the
batte ry terminals.
&_ WARNING
To avoid se rious personal injury and damage
to the veh icle, heed all war nings and inst ruc­
tion s of the jumper cable m anufa cture r.
If in
d oubt, cal l for ro ad service.
- Ju mpe r cabl es must be lo ng enoug h so tha t
t he vehicles do no t tou ch.
- When conne cting jumper cables, make sure
th at they c an not get c aug ht in any moving
p art s in the engine com partmen t.
- B efore you check any thing in the e ngine
comp artment, alw ays re ad an d hee d all
WAR NINGS
~ page 218.

M N <( I.J "". rl I.O
"' N I.O rl
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE( +) to POSITIVE
( + ), and NEGATIVE( -) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw plugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described
above ap­
plies specifically to the case of your vehicle
being jump started. When you are giving a
jump sta rt to another vehicle, do
not con­
nect the negative(-) cab le to the negative
( - ) terminal on the discharged battery @
r:::;, fig. 216. Instead, secure ly connect the
negative(-) cab le to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outs ide, escap ing battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The follow ing information is to be used by com­
mercial tow truck operators who know how to op­
erate their eq uipment safe ly.
- Never t ow your Audi. To wing will cau se da m ­
age to the engine and tran smi ssion .
- Neve r wrap th e safety cha in s or win ch cab le s
around the brake line s.
- To pre vent unnecess ary dama ge, your A udi
mu st b e trans port ed w ith a fl at b ed t ru ck .
- To lo ad the vehicle on to th e flat bed, us e the
towing l oop found in th e vehicle tool s and at­
tach to th e fr ont or re a r anc hora ge
¢ page 267 and ¢page 268.
Emergen cy situati ons
A WARNING
-A veh icle being towed is not safe for passen-
gers. Neve r all ow anyone to ride in a vehicle
being towed, for any reason .
Front towing loop
Fig. 217 Fro nt bumper: cover
Fig . 2 18 Fro nt bumper : insta lling the tow ing loop
The threaded opening for the towing loop is lo­
cated behind a
cover on the right side of the front
bumper .
.,. Remove the towing loop from the vehicle tool
kit¢
page 253.
.,. Press the lower area of the cap inward with
quick, strong pressure
r::;, fig . 217 . The cap w ill
loosen from the bumper .
.,. Tighten the towing loop in the threaded open­
ing until it stops
¢ fig. 218 and then tighten it
w ith a wheel wrench .
.,. After using, p lace the towing loop back in the
vehicle tool k it.
A WARNING
--
If the towing loop is not tightened until it
stops when installing, the threads may be
267

M N <( I.J "". rl I.O
"' N I.O rl
Raising the vehicle
lifting with workshop hoist and with floor
jack
The vehicle may only be lift ed at the lifting
poin ts illustra ted.
F ig. 222 Front lift in g po int
F ig. 223 Rear lift in g point
.,. Read and heed WARNING ¢ .&_.
.,. Activate the vehicle jack mode* in the M MI:
I CAR I funct ion button> (Car )* systems control
button >
Servicing & checks > Air susp.: jack
mode > On .
.. Locate lifting points¢ fig. 222 and¢ fig. 223 .
.. Adju st lift ing a rm s of wor ksh op hoist or floor
jack t o match ve hicle lifting poi nts.
.. Inse rt a r ubber pa d between the floor jac k/
workshop hoist and the lifting poi nts.
T he vehicle jac k mode* mus t be activa ted so that
the au tomatic a djust ment of the Adaptive Air
Suspension * does not make it more diffi cult to
ra ise the veh icle with the floor jack.
If you must lift your vehicle with a floor jack to
work underneath , be sure the vehicle is safely
supported on stands intended for this purpose.
Emergency situations
Front lifting point
T he li ftin g po in t is loca ted o n the floo r pan rein­
f o rcement about at the same level as the ja ck
mounting point¢
fig. 222 . Do not lift the vehi­
cle at the vertical sill reinforcement.
Rear lifting point
T he lifti ng po int is loc ated o n the vert ica l rei n­
f o rcement o f the lower s ill for the on- bo ar d ja ck
¢ fig. 223.
lifting with vehicle jack
Refer to¢ page 257 .
A WARNING
- To reduce t he ris k o f ser ious injury and vehi­
cle damag e.
- Always lift the vehicle only at the specia l
workshop h oist a nd f loor jack lift poi nts il­
lu strat ed¢
fig. 222 and ¢ fig. 223.
- Fail ure to lift the ve hicle at these points
could cause the veh icle to tilt o r fall from
a lift if there is a cha nge in veh icle weight
dis tributi on and balance . T his might hap ­
p en, fo r example, wh en h eavy compone nts
s uch as th e engine blo ck or trans missi on
are re m ove d.
- Wh en removing heavy comp onents li ke
t he se, an ch or veh icle to h ois t o r ad d corre­
spon ding we ights to m aintai n the c enter of
g ravity . Otherwise, the vehicle might tilt or
slip off the hoist , causing ser ious persona l
i nju ry .
(D Note
- B e aw are o f the following poi nts befo re li ft­
ing the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil
pan, the transmission housing, the front
or rear axle or the body side members.
Thi s could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in ­
serted between the floor ja ck and the lift
point s. .,,.
269

Technical data
Vehicle identification
F ig. 22 4 Vehicl e Ide ntificat io n Number (VlN) plate: loca ·
t io n on drive r's s id e das h pane l
XXXXX XX -X -XXXX XXX XX
CD+ ~t :1:: xxxxxxxx xx x xxxxxxxx
T VP /fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~ l xxxx ; xxxx xxx ; xx
II.· AUSS, I OPTIONS
E0 A
7D5 4UB 6XM 5SG 5RW
2EH J0Z lLB l
A S lB A
3FC SMU 7Xl
F0A 9G3 0G7
0YH 0JF
T L6 3KA 8EH Ul A X98 QZ7
l X W 803 908 824 020
7T6 CV7 7K0 4X3 2K2
3L4 4KC 3Y0 413
502
lSA 7GB 01A 4G0
XX. X XX X XX X xxxx
Fig. 225 T he veh icle iden ti fica tion label -inside the lug ·
g age compart ment
Vehicle Identification Number (VlN )
The Veh icle Iden tifica tion Number is located in
d iffe rent p laces:
- u nder the w indshield on the dr iver's side
¢ fig . 224.
-in the MMI: Select: Funct ion button ICAR I >
(Car )* syste ms> Servi cing & checks > VIN
~ numb er.
i3 -on the vehicle identification label.
"". rl I.O
"' N I.O rl
Technical d ata
Vehicle identification label
The vehicle identification label is lo cate d in the
lu ggage compartment in the spare whee l we ll.
T he labe l¢
fig. 225 shows the fo llowing vehicle
da ta:
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle type , engine o utp ut, transmission
® Engine and transm iss ion code
@ Paint number and interior
® Optional equipment numbers
T he information of the veh icle identification label
c a n a lso be fo und in your W arranty
& Mai nte·
nance booklet.
Safety compliance sticker
The safety compliance sticker is you r assurance
that your new vehi cle complies w ith all applicable
Fede ra l Mo tor Vehi cle Safety Sta ndards which
were in effec t at the time the vehicle was m anu­
fac tured. Yo u can find this sticker on the door
jamb on the driver 's side. It shows the month and
year of production and the vehicle identification number of your vehicle (perforation) as we ll as
the Gross Veh icle Weight Rating (GVWR) and the
Gross Axle Weight Rating (GAWR).
H igh vo ltage warn ing lab el
T he high voltage wa rning label is located in the
engine compartment next to the eng ine hood re ­
lease. The spark ign it ion system complies with
t h e Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a st icker on the door jamb
on the dr iver 's side.
The Gross Vehicle Weight Rat ing includes the
weight of the basic vehicle plus f ull fuel tank, oil
and coolant, pl us maxim um load, which includes
passenger weigh t (150 lbs/68 kg per design ated
seat ing pos ition) and luggage weight ¢.&, . ..,,.
271

Technical data
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum
load that can be applied at each axle of the vehi ­
cle ¢& .
Vehicle capacity weight
The vehicle capacity we ight (max. load) is listed
eithe r on the driver's side B-pillar or inside the
fue l filler f lap.
A WARNING
- The actual Gross Axle Weight Rating at the
front and rear axles should not exceed the
permissible weights, and their combination
must not exceed the Gross Vehicle Weight
Rating .
Dimensions
Length i
n (mm)
Width in
(mm)
Width (across mirrors) in (mm)
Height (unloaded)al in
(mm) -
Exceeding permissible weight ratings can
result in veh icle damage, acc idents and per­
sonal injury.
(D Note
-The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transporting a heavy load in the luggage
compartment, carry the load as near to the
rear axle as possible so that the vehicle's
hand ling is not impaired.
- Do not exceed the maximum permissible
axle loads or the maximum gross veh icle
we ight. Always remember that the vehicle's
hand ling will be affected by the extra load.
T herefore, adjust your speed accordingly.
- Always observe local regulations.
A7 S7
196.2 (4984) 196 .3 (4985)
75.2 (1911) 75 .2 (1911)
84.2 (2139) 84.2 (2139)
55.9 (1420) 55 .0 (1398)
al Th e he igh t of th e vehicl e de pe nd s on th e tires a nd the su sp ension .
When driving up steep ramps, on rough roads,
over curbs, etc. it is important to remember that
some parts of your vehicle, such as spo ilers or ex-
Capacities
Fuel tank: tota l capacity
- gasoline engine
- diesel engine
Windsh ield f lu id container
Windshield and headlight washer fluid container*
272
haust system components, may be close to the
ground. Be careful not to damage them.
gal (liters) approx. 19.8 (75.0)
gal (liters) approx. 19.3 (73.0)
quarts (liters) approx. 3.7 (3.5)
quarts (liters) approx. 5.2 (4.9)

M N <( (.J
'SI: ,...., \!) ..,.,
N \!) ,....,
Technical d at a
Gasoline engines
A7 3.0, 6 cylinder
Maximum output SAE net hp@rpnn 333 @ 5300 -6500
Maximum torque SAE net lb-ft@ rpm 325@ 2900 -5300
Displacement CID (cm
3
) 182 (2995)
Engine oil with filter change
1>
Fuel Premium un lead ed (9 1 A KI), ¢ page 210, Gasoline
57 4.0, 8 cylinder
Maximum output SAE net hp@ rpnn 450 @ 5800 -6400
Maximum torque SAE net lb
-ft@ rpm 406@ 1400 -5700
Displacement CID (cm
3
) 243.7 (3993)
Engine oil with filter change
1
)
Fuel Pr emi um un lead ed (9 1 AKI), ¢ page 210, Gasoline
Diesel engines
A7 3.0 TOI, 6 cylinder
Maximum output SA E net hp@rpnn
Maximum torque SAE net lb-ft@ rpm
Displacement C
ID (cm
3
)
Engine oil with filter change1
)
Fuel UL SD N o. 2 , ¢ page 211, Diesel fuel
l) For specific engine oil capacities, please see
the mos t current informat ion for the USA at
h ttp ://www.audiusa.com/he lp/maintenance or
for Canada at http://www.audi.ca/ca/brand/ en/
your_audi/audi_services _and/Care _and _Mainte­
nance/schedu le . html or call 800-822-2834. 239@ 3500
-3750
428@ 1750 -2250
181 (2967)
27 3