engine oil AUDI A7 2017 Owner´s Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2017, Model line: A7, Model: AUDI A7 2017Pages: 284, PDF Size: 72.29 MB
Page 127 of 284

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Winter tires
By using all wheel drive, your vehicle has good
forward motion with standard tires in winter conÂ
ditions . However, in winter we recommend using
winter or all season tires on all four wheels, beÂ
cause this will improve the braking effect.
Snow chains
If there are snow chain laws, snow chains must
also be used on vehicles with all wheel drive
¢ page 227, Snow chains.
Replacing tires
For vehicles w ith all whee l dr ive, only whee ls w ith
the same rolling circumference should be used .
Avoid using tires with different tread depths
¢ page 218, New tires or wheels.
Offroad vehicle?
Your Audi is not an offroad vehicle -there is not
enough ground clearance. For this reason, avoid
difficult terrain.
_& WARNING
-Also, in vehicles with a ll wheel drive, adapt
your dr iving style to the current road and
traff ic conditions. Do not let the increased
safety provided tempt you into taking risks,
because this increases the risk of an acciÂ
dent .
- The braking ability of your vehicle is limited
to the traction of the wheels . In this way, it
is not different from a two wheel dr ive vehiÂ
cle. Do not be tempted to accelerate to a
high speed when the road is slippery, beÂ
cause this increases the risk of an accident .
- Note that on wet streets, the front wheels
can "hydroplane" if driving at speeds that
are too high. Unlike front wheel drive
vehicles, the engine does not rev higher sudÂ
denly when the vehicle begins hydroplaning .
For this reason, adapt your speed to the
road conditions to reduce the risk of an acciÂ
dent.
Intelligent Technology
Rear spoiler
The extendable rear spoiler increases driving staÂ
bility.
Fig. 141 Center console: button for the rear spoiler
T he rear spo iler retracts and extends. Var ious opÂ
erating modes (automatic o r manua l mode) can
be activated .
Automatic mode (normal operation)
-Extends automatically: when the vehicle speed
exceeds approx imately 80 mph (130 km/h) .
- Retracts automat ically: when the vehicle speed
drops below approx imately SO mph (80 km/h).
Manual mode
- Extending manually: briefly tap the button to
fully extend the rear spoiler.
- Retracting manually: when driving at speeds
below approximately 10 mph (20 km/h), press
and hold the button to retract the rear spoiler.
When at speeds between 10 mph (20 km/h)
and 80 mph (130 km/h), the rear spoiler will
completely retract when you tap the button.
Indicator lights
lfa /. Rear spoiler: System fault!
The rear spoiler may not have extended due to a
malfunction . This cou ld change the vehicle 's drivÂ
ing characteristics at high speeds. Do not drive
faster than 85 mph (140 km/h) . Drive to an auÂ
thorized Audi dealer or authorized Audi Service Facility immed iately to have the malfunction cor Â
rected . The color of the indicator light depends
on the vehicle speed .
125
Page 128 of 284

Intelligent Technology
& WARNING
When extending and retracting the rear spoilÂ
er, make sure there are no persons or objects
w ith in the spoiler range to red uce the risk of
injury .
& WARNING
Driv ing at higher speeds w ithout the rear
spoiler dep loyed can impa ir hand ling ch aracÂ
t er istics, mak ing t he vehi cle h arder to conÂ
t rol.
- Always make sure tha t the spoiler is deÂ
ployed whe n driving a t speeds ove r 85 mph
(140 km/h) . If the rear spoiler warning/ind iÂ
cator light in the instrument cluster comes
on, the rear spo iler may not have deployed.
- Never drive at speeds higher than 85 mph (140 km/ h) if the spoile r is not deployed.
Have the spoiler inspected as soon as possiÂ
ble by an author ized Audi dealer or qualif ied
workshop.
-Always obey speed limits and other tra ffic
laws .
(D Note
-Never push on the vehicle on the rear spoi lÂ
er . This cou ld cause damage.
- To prevent damage to the rear spoiler do
not lean o r place anything on it.
- Only opera te the rear spoiler man ually when
the luggage compartment lid is close and
the rear spoiler movi ng pa rts a re not
blocked. Otherwise, damage could occur.
(D Tips
Clean the rear spoi ler compartment eve ry 2 to
3 mont hs. To function correctly, the rear
spoiler m ust be free of ice, snow and leaves.
126
Energy management
' The starting ability is optimized
T he energy management system manages the
electrical energy distribution and optimizes the
availability of electrical energy for starting the
engine.
When a vehicle with a conventional energy sys Â
tem is no t drive n for a long time, the ve hicle batÂ
te ry is drained by equ ipment (fo r example, t he
i mmob il iz er). I n cer ta in circ umstan ces, the re
could m ay no t be e nough energy to s tart the enÂ
gine.
You r vehicle is equipped with an inte lligent e nerÂ
gy management system fo r dist ributing elec triciÂ
ty. Thi s sign ifica ntl y improves the start ing ability
and incre ases the vehicle battery life .
The ene rgy ma nagement system Is made up of
battery diagnosi s, idling current management ,
and dynamic energy management .
Battery diagnosis
T he battery diagnos is determines the vehicle bat Â
tery charge level. The sensors detect the ba tte ry,
the batt ery cur rent, and t he battery temperature .
The curren t cha rge level and the pe rformance of
t h e ve hicle battery are dete rm ined based on th is .
Idling current management
The idling current management decreases the
energy used while parked . With the engine
switched off , it m anages t he e ne rgy dis trib ution
to the d ifferen t electr ica l components . Data from
t h e b attery d iagnosis is ta ken into a ccou nt for
th is .
De pen ding on the vehicle batte ry c ha rge level,
e le ctri ca l eq uipme nt is switched off one i tem af Â
te r th e o ther to p revent t he vehi cle b attery from
dra ining and to ma intain the s tarting ab ility.
Dynamic energy management
While dr iv ing , dynam ic energy management disÂ
t ributes the app ropr iate amo unt of energy to t he
ele ctrica l eq uipm ent. It contro ls t he batte ry
c harge level so tha t the amou nt o f energy is no t
ll>
Page 194 of 284

Check ing and F illing
fi ll up at busy gas stations where the seasona l
adjustm ent is more likely to be mad e in time .
0 Note
-Me thanol f uels which do no t meet these reÂ
quirements may cause corrosion and damÂ
age to plastic and rubber components in the
fuel system .
- Do not use fuels that fail to meet the spec iÂ
fied criteria in this chapter .
- If you are unable to determine whether or not a particular fuel blend meets the spec iÂ
fications, ask your service station or its fuel supplier.
- Do not use fuel for which the contents canÂ
not be identified.
- Fuel system damage and performance probÂ
lems resulting from the use of fue ls differÂ
ent from those specified are not the responÂ
s ibility of Audi and are not covered under
the New Veh icle or the Emiss ion Control
System Warranties.
- If you experience a loss of fuel economy or
driveability and performance problems due
to the use of one of these fuel b lends, we
r ecommend that you switch to unblended
fuel.
Gasoline additives
A ma jo r concern among many auto manufacturÂ
ers is carbon deposit build- up ca used by the type
of gasoline you use.
A lthough gasoline grades d iffer from one manuÂ
facturer to another, they have cer tain things in
common . All gaso line grades contain substances
that can cause deposits to collect on vita l engine
parts, such as fue l injectors and intake valves. AlÂ
though most gasoline brands include additives to
keep engine and fuel systems clean, they are not
equally effective .
Audi recommends using TOP TIE R Detergent GasÂ
oline. For more information on TOP TIER Deter Â
gent Gasoline, please go to the official website (www.toptiergas .com) .
192
After an extended period o f using inadequate
fuels, carbon deposit bui ld-ups can rob your enÂ
gine of peak performance.
([) Note
Damage or ma lf u nction due to poor fue l qual Â
ity is not covered by the Audi New Vehicle
Limited Warranty .
Diesel fuel
Applies to: vehicles wi th diese l en gin e
Always use ULSD (Ultra Low Sulfur Diese l) No. 2 .
The ULSD No. 2 meets the ASTM D97S.
D iesel fuel w ith concentrations of b iod iesel highÂ
er than 5 % such as B l 1, B20 or BlOO are st rict ly
prohibited .
Se rvice station fuel pumps are labe led wi th the
correc t fu el i nfo rmation for easy recogn ition by
the user . If the diesel fue l pump is not labe led
ask the station operator what fue l is being disÂ
pensed before filling up your vehicle .
U LSD No . 2 may no t be ava ilable outside the USA
and Canada . Be s ure to check befo re t raveling to
other countries .
U LSD No . 2 can become th ic k e r i n very co ld temÂ
peratures, and this can impa ir the e ng ine's s tartÂ
i ng and running . Depend ing on the season, gas
stations provide ULSD No . 2 that flows better in
cold temperatures so that you can continue operÂ
at ing your vehicle as usual.
(D Note
- Your vehicle's diese l engine was designed
so ley for use with ULSD No . 2 . Therefore,
never use gasoline, heating oil, other fuels
or flow improvers. These contain substances
that will severely damage the fuel system and the engine. Such damage will not be
covered by your New Vehicle Limited WarÂ
ranty.
- If you put any amo unt of incorrect fuel in
the fuel tank, do not start the engine under
any c ircumstances. Immed iate ly contact the
nearest author ized A udi dealer or author-
ized Aud i Serv ice Facility fo r ass istance .
IJ,-
Page 200 of 284

Check ing and F illing
is empty or until no mo re fluid flows into the
tank.
~ Remove the canister and close the fi ller tube
c> page 198 , Completing AdBlue refill .
(D Note
Only use refi ll canisters that are approved for
your vehicle. Us ing other systems can cause
Ad Blue to leak.
@ Tips
- An authorized Audi dealer or authorized
Audi repair facility can te ll you which ref ill
can isters are approved for your vehicle.
- A permitted refill canister contains approxiÂ
mately 1.3 ga llons (5 liters) of AdB lue.
Completing AdBlue refill
Applies to: vehicles with selective catalytic reduction
C losi ng the filler neck
~ Turn the cap on the filler neck to the right with
the wheel wrench unt il the cap clicks into place.
This t ightens the cap to the specification o &
in Filling AdBlue on page 197, c> (D in Filling
AdBlue on page 197 .
~ The n press on the left side of the tank doo r un-
ti l it l atches.
After filling
The vehicle must be driven so that the system
recognizes that the Ad Blue was refilled . T his can
take severa l m in utes.
~ If there was no Ad Blue left in the tank and a
range of O mi (0 km) was shown in the d isplay,
switch the ign it ion on for about 30 seconds beÂ
fo re sta rting the engine.
(D Tips
Ad Blue can freeze at very low temperat ures .
If this happens, the system will not detect
that the Ad Blue was refilled a nd it will continÂ
ue to inform yo u of the low Ad Blue level. The
message turns off as soon as the tank thaws
out again.
198
Catalytic converter
Applies to: vehicles with gasoline engine
It is very important that your emission control
system (catalytic converter) is func tioning propÂ
erly to ensure that your vehicle is running in an
environmentally sound manner .
~ Always use lead-free gasoline c> page 191, Fuel
supply .
~ Never run the tank down all the way to empty.
~ Never put too much motor o il in your engine
c> page 204, Adding engine oil.
~ Never try to push- o r tow-start your vehicle .
The catalytic converter is an efficient "clean -up "
device built into the exhaust system of the veh iÂ
cle. The catalyt ic converter b urns many of the
po llutants in the exhaust g as befo re they are reÂ
l eased into the atmosphere.
The exclusive use of un leaded fuel is critically imÂ
po rtant fo r the life of the catalytic converte r and
prope r funct io ni ng of the engine.
_&. WARNING
The temperat ure of the exhaus t sys tem is
high, both when driv ing and a fter stopping
the engine.
-
- Never tou ch the exhaust tail pipes once they
have become hot. This cou ld resu lt in burns.
- D o not p ark or operate the vehicle in ar eas
where the hot exhaust system may come in
contact with dry g rass, brush, fuel spi ll or
other mate rial which can ca use a fire.
- Do not apply additiona l undercoating or
rustp roofing on or near the exhaust maniÂ
fold, exha ust pipes, cata lytic conve rter or
heat shields . D uring driving, the substance
used for unde rcoat ing could overheat and
cause a fire .
Cl) Note
-Be aware that just one tank f illing wit h
leaded fu e l w ill already seriously degrade
the performance of the catalytic converter.
- Do not exceed the correct engine oil leve l
c>page204.
Page 202 of 284

Checking and Filling
-Do not remove the engine cover under any
circumstances . This increases the risk of
burns.
- If tests need to be performed with the enÂ
gine running, there is additional danger due
to moving components (such as the ribbed belt, alternator and radiator fan) and from
the high voltage ignition system.
- Do not under any circumstances give gas inÂ
advertently (for example, by hand from the
engine compartment) if the vehicle is staÂ
tionary but the engine is running and a gear
is engaged. Otherwise, the vehicle will start
to move immediately and this could result
in an accident.
- Pay attention to the following warnings listÂ
ed when work on the fuel system or on the
electrical equipment is required.
- Do not smoke .
- Never work near open flames.
- Always have a working fire extinguisher
nearby
- All work on the battery or electrical system
in your vehicle can result in injuries, chemi·
cal burns, accidents or burns. Because of
this, all work must be performed
only by an
authorized Audi dealer or authorized Audi
Service Facility.
- To reduce the risk of electric shock and inÂ
jury, never touch the following components when the engine is running or is being startÂ
ed :
- Ignition cable
- Other components in the electronic high-
voltage ignition system
-If you must check or perform work on the
engine while it is running:
- Set the parking brake and place the selecÂ
tor lever in the P (park) position first .
- Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compoÂ
nents. Tie back long hair before beginning
work and do not wear clothing that can
hang down into the engine.
200
-Limit your exposure to exhaust and chemiÂ
cals to as short a time as possible
c> A .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of CaliÂ
fornia to cause cancer and birth defects and
reproductive harm . In addition, certain fluÂ
ids contained in vehicles and certain prodÂ
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
- Battery posts, terminals and related accesÂ
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the fluÂ
ids up. Otherwise severe malfunctions and enÂ
gine damage will occur.
@:) For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly. If
there are visible spots from oil or other fluids, bring your vehicle to an authorized Audi dealÂ
er or authori zed Audi Service Facility to be
checked.
Page 204 of 284

Checking and Filling
Engine compartment overview
The most important check points.
Fig. 184 Typical location of the rese rvoir and the engine o il fil le r open ing
(D Jump start po int(-) with hex head screw
<::;> page 208, <::;> page 254
@ Ju mp start point(+) under a cover
<::;> page 208, ¢ page 254
® Engine oil label* with VW standard
<::;> page 202
@ Brake fluid reservoir ((0)) <::;> page 207
® Engine oil filling opening (~)¢page 204
@ Coolant reservoir (- L) ¢ page 206
(j) Washer fluid reservoir (0) ¢ page 209
The engine oil f illing opening (item@) may be
located in a differe nt area depending on the enÂ
gine version .
A WARNING
Read and follow the WARNINGS before
checking anything in the engine compartment
¢ .&. in Working in the engine compartment
on page 199.
202
Engine oil
Engine oil specifications
The engine oil used must conform to exact speciÂ
fications.
The service interval display in the instrumen t
cluster of your vehicle will inform you when it is
time for an oi l change. We recommend that you
have your oi l changed by an authorized Audi ServÂ
ice Advisor.
If you must add oil between oil changes, use an
oi l that matches the Audi oil quality standard
listed on the sticker. The sticker is located at the
front of the eng ine compartment ¢
page 202,
fig. 184 .
Audi recommends
~Castrol /fg/j;Sf.g;fg f'r
engine oil from Aud i Genuine Parts .,_
Page 205 of 284

co
co
.... N
" N .... 0
00
\.J '
functionality and s ervice life of the engine. Your
engine was factory-filled with a high -quality oil
which can usually be used throughout the entire
yea r.
Note
Your Limited New Vehicle Warranty does not
cover damage or malfunctions d ue to failure
to follow rec ommended maintenance and use
requireme nts as s et forth in the Audi Owner's
Manual and Warranty & Maintenance booklet .
- Use only a high quality engine oi l that ex-
pressly complies with the Au di oil quality
standard specified for your vehicle's engine.
Using any o ther oil can cause serious engine
damage.
- Do not mix any lubricants o r other additives
into the engine oil. Doing so can cause enÂ
gine damage.
@ Tips
If you need to add oil and there is none availaÂ
ble that meets the Audi o il quality standard
your eng ine requ ires, you may add a total of
no more than 0 .5 qt (0.5 l) of a h igh-quali ty
"synthet ic"oil that meets the following speci Â
fications.
- Applies to: gaso line engine: ACEA A3 or
API SM with a viscosity grade of SAE OW-30,
SAE 5W-30 or SAE 5W-40.
- Applies to: diesel engine: ACEA C3 or API CF
with a viscosity grade of SAE OW-30 o r
SAE 5W-30 .
- For more information about engine oil that
has been approved for your vehicle, please
contact e ither your authori zed Audi dea ler
or Audi Customer Relat ions at
1 (800) 822-2834 or visit our web site at
www .audiusa .com or www .aud ica nada.ca.
Engine oil consumption
The engine in your vehicle depends on an adeÂ
quate amount of oil to lubricate and cool all of
its moving parts .
In order to provide effective lub rication and coolÂ
ing of in ternal engine componen ts, all internal
Ch eck ing and Filling
combustion engines consume a certain amo unt
of oil. Oil consumption vari es from engin e to enÂ
gine and may change s ignificantly over the life of
the engine . Typ ically, engines w ith a specified
break-in period (see¢
page 65) consume mo re
o il during the break -in per iod than they consume
after o il consumption has stab il ized .
Under normal cond itions, the rate of oil con Â
sump tion depends on the qu ality and viscos ity of
the oil, the RPM (revolutions per minute) at
wh ich the engine is operated, the amb ient temÂ
perature and road co ndit ions. Further facto rs a re
the amount of oi l di lution from wate r condensa Â
tion or fuel resid ue and the oxidat ion level of the
o il. As any engine is subject to wear as mileage
builds up, the oil consumption may increase over
time unti l replac ement of worn components may
become necessary.
With a ll these variab les coming into play, no
standard rate of oil consumption can be estab Â
li sh ed or sp ecified . There is no alternative to regÂ
u lar and frequent checking of the oi l level, see
Note .
If the yellow engine oil leve l warning symbo l in
the instr ument cluster
Ill lights up, yo u should
check the oi l level as soon as possible
¢
page 204. Top off the o il at your earliest conÂ
venience ¢
page 204 .
A WARNING
-Before you check anyt hing in the engine com -
partment, always read and heed all WARNÂ
INGS
¢ .&. in Working in the engine compartÂ
ment on page 199.
{(D Note
Driving w it h an insufficient oil level is likely to
cause severe damage to the eng ine .
(D Tips
-The oil pressure wa rn ing display. is not
an indicator of the o il leve l. Do not rely on
i t . Instead, check th e oil level in your enÂ
gine at regular interval s, preferably each
time you refuel, and alway s before going
on a long trip .
203
Page 206 of 284

Check ing and F illing
- If you have the impression your engine con Â
sumes excessive amounts of oil, we recom mend that you consu lt your Audi dealer to
have the cause of your concern properly diÂ
agnosed . Keep in mind that the accurate
measurement of oil consumption requi res
great care and may take some time . Your
Audi dealer has inst ructions about how to
measure oil consump tion accurate ly.
Checking the engine oil level and adding
engine oil
The engine oil level can be checked in the InfoÂ
tainment system
F ig. 18 5 Eng ine co mpar tment : en gin e o il fille r open ing
cove r
Obse rve the sa fe ty precau tions ¢&. in Working
in the engine compartment on page 199 .
Checking the engine oil level
.,. Park the vehicle on a level surface .
.,. Sh ut the engine off w hen it is warm . Wait apÂ
prox imately two m inutes so tha t the engine oil
can flow back in to the o il pa n .
.,. Switc h only the ignit ion back on.
.,. Se lect: the
ICARI function button > ( Car )* Sy sÂ
tems
control b utton > Service & checks > Oil
level.
.,. Read the oil level in the Infota inment system.
Add engine oil if the bar in the oil leve l indicaÂ
tor is just before "min".
Adding engine oil
.,. Turn the eng ine off .
.,. Unscrew the engine oil filler opening cap~
¢ fig.185, ¢page 202, fig.184 .
.,. Carefully add 0 .5 quart (0 .5 liter) of the correct
o il ¢ page 202.
204
.,. Close the eng ine oi l filler opening ca p~ -
.,. Close the hood, restart the ignition after two
m inutes and read t he current o il level in the InÂ
fotainment system.
A WARNING
- When adding oil, do not let oil dr ip onto hot
engine components . This inc reases the risk
of afire.
- You must sea l the cap on the oi l filler openÂ
ing correct ly so that oi l does not leak out
on to the hot e ngine and exha ust system
w hen t he e ngine is runni ng, bec ause this is
a fire ha zar d.
- Always clean s kin thoroughly if it comes into
con tact with eng ine oil.
0 Note
- The engine o il level must not be under the
" min " mark ing, beca use this increases the
r isk of engine damage.
- If the message
Oil level is too full. Please
reduce oil level.
appea rs, there is too m uch
o il i n t he engi ne a nd there is a risk of cata Â
lyt ic converter and engine damage . D o no t
sta rt the eng ine. Co nta ct an a uth o rize d Aud i
dealer or authorized Audi Service Facility to
have excess engine oil extracted if necessaÂ
ry.
- Do not mix any ad ditiona l lubr icants into
the engine oil. Damage caused by such add iÂ
t ives is not covered by the wa rranty .
@ For the sake of the environment
- Oil sho uld never enter the sewer system or
come into contact with the ground .
- Pay attention to lega l req uiremen ts when
disposing of empty o il containers .
(D Tips
-Th e oil leve l in dica tor in the inst rument
cl uster d is p lay is only an i nformationa l dis Â
play. If the o il level is too low, a minim um
oil warn ing appears in the instrument clusÂ
ter . Add o il and close the hood. The c urrent
oil leve l is d isplayed in the Infotainment
Page 207 of 284

co
co
.... N
" N .... 0
00
\.J -
switched on .
- The engine oi l consumption may be up to
0.5 quart/600 miles (0.5 liter/1,000 km),
depending on driving style and operating
conditions. In RS models, the oil consumpÂ
tion may be up to 1 qt/600 mi (0.8 L/ 1,000 km). Consumption may be higher
during the first 3,000 miles (5,000 km). BeÂ
cause of this, the engine oil level must be
checked regular ly.
It would be best to check
each time you ref uel your veh icle and befo re
l ong d rives.
Changing the engine oil
We recommend that hove your oil changed by on
authorized Audi dealer or a qualified service staÂ
tion .
Before you check a nyth ing in the eng ine compartÂ
ment,
alway s re ad and heed all WARNING S 9 &.
in Working in the engine comportment on
page 199.
The engine oil must be changed according to the
intervals specified in you r Warranty
& MainteÂ
n ance booklet. This is very impo rtant because the
l ub ricating properties of oil diminish gradually
during normal vehicle use.
Unde r some ci rcumstances the e ngine o il should
be cha nged more frequently . Change oil mo re ofÂ
ten if yo u drive mostly short distances, operate
the vehicle in dusty areas or under predominant ly
stop-and-go traffic conditions, or have your vehiÂ
cle where temperatures remain below freezing
for extended periods.
Detergent additives in the oil will make fresh oil
l ook dark after the engine has been running for a
short time. Th is is normal and is not a reason to
change the oil more often than recommended.
Because of the problem of proper disposa l, along
with the special tools and necessary expertise reÂ
q ui red, we strongly recommend that you have
your oil changed by an authorized
A ud i dealer or
a qualified service station.
If you choose to chang e your o il your self, please
note the following important information:
Ch eck ing and Filling
A WARNING
To reduce the risk of persona l injury if you
must change the eng ine oil in you r vehicle
yourself:
- Wear eye protect ion.
-
- To reduce the r isk of burns from hot engine
oil, let the engine cool down to the touch.
- When remov ing the oil drain plug w ith your
f ingers, stay as far away as possible. Always
keep your forearm parallel to the ground to
help prevent hot oil from running down your
arm.
- Drain the oil into a container designed for
this purpose, one la rge enough to hold at
least the tota l amount of oi l in you r engine .
- Engine oil is poisonous. Keep it we ll out of
the reach of children.
- Continuous contact with used engine o il is
harmf ul to your skin. Always protect your
skin by washing oil off thoroughly with soap
and wate r.
Q) Note
Never mix oil additives with your engine oil.
These additives can damage your engine and
adverse ly affect you r Audi limited New VehiÂ
cle Warranty.
@ For the sake of the environment
- Before chang ing your oi l, first make sure
you know where you can properly d ispose of
the used oil.
- Always dispose of used e ngine o il properly .
Do not dump it on ga rden soil, wooded
areas, into open streams o r down sewage
dra ins.
- Recycle used e ngine o il by ta king it to a used
eng ine oil collection fac ility in yo ur area, or
c ont act a se rvice station.
Cooling system
Coolant
The eng ine cooling system is fi lled w ith a mixture
of purified water and coolant additive at the fac-
tory. This coolant m ust not be not changed . .,._
205
Page 208 of 284

Check ing and F illing
The coolant leve l is monitored through the. inÂ
dicator light ¢
page 14. However, we do recomÂ
mend occasionally check ing the coo lant level
manually.
I f you must add coolant, use a mixture of water
and coolant additive. Mixing the coolant additive
with d istilled water is recommended.
Coolant additiv e
The coolant addi tive is made of anti-freezi ng and
corros ion protection agents. Only use the fo llowÂ
ing coolant additives . These additives may be
mixed with each other.
Coolant additive Specification
Gl3 TL 774)
Gl2++
TL 774 G
The amount of coolant add itive that needs to be
mixed w ith water depends on the climate where
the vehicle will be operated. If the coolant addiÂ
tive percentage is too low, the coolant can freeze
a nd damage the engine.
Coolant
Freeze protec·
additive tion
Warm reg ions min. 40% m in. -13 ° F
max. 45% (-25 °C)
Cold regions min. 50% max . -40 °F
max . 55% (-40 °C)
([)
Note
-Before the start of winter, have your authorÂ
ized Audi dealer or authorized A udi Se rvice
Fac ility check if the coolant additive in you r
vehicle matches the percentage approp riate
fo r the clim ate. Thi s is especially important
when driving in co lder climates .
- If the approp riate coolant additive is not
available in an emergen cy, do no t add any
other additive. You cou ld damage the en Â
gine. If this happens, only use water and re store the correct mixture ratio with the
spec ified coolant additive as soon as possiÂ
ble.
- Only refill with new coo lant.
- Radiator sealant must not be mixed w ith
the coo lant .
206
· Adding coolant
F ig. 186 En gin e compartment : coolant exp ansion tank
cover
-N
-~
~
Observe the safety precautions ~ .&. in Working
in the engine compartment on page 199.
Check ing the engin e coolant level
Park the vehicle on a leve l surface.
.,. Switch the ignit ion off.
.,. Read the coolant level on the coolant expansion
tank ¢
page 202, fig . 184. The coolant level
must be betwee n the MIN and MAX mark ings
when the e ngine in co ld. When the engine is
wa rm it c an be slightly above the MAX marking.
Adding coolant
Requirement: there must be a residual amount of
coolant in the expansion tank ¢(D .
.,. Let the engine cool down .
.,. Place a cloth over the coolant expansion tank
cap and unscrew the cap counterclockw ise
¢ .8_ .
.,. Add coo lant m ixed in the correct rat io
¢ page 205 up to t he MAX mar king.
.,. Make sure that the f luid level remains stab le.
Add mo re coolant if necessary.
.,. Close the cap securely .
Coolant loss usually ind icates there is a lea k. ImÂ
med iate ly dr ive your vehi cle to a n author ized
Audi dealer or author ized A udi Service Fac ility
and have the cooling system inspected . If the
cooling system is not leaking, a loss can come
from the coolant boiling through overheating
and being pushed out of the cooling system.