flat tire AUDI A7 2018 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2018, Model line: A7, Model: AUDI A7 2018Pages: 274, PDF Size: 42.77 MB
Page 239 of 274

a co ,...,
N
" N ,...,
0 00 <..:l '
control button > Servicing & check s > Air
s u sp .: jack mode > Off .
The vehicle jack mode* swi tches off automatical
l y at speeds above 6 mph ( 10 km/h).
_& WARNING
Always read and follow all WARNINGS and in
formation
c:> ,1,. in Raising the vehicle on
page 239
and c:> page 241.
After changing a wheel
A wheel change is not complete without the do
ing the following.
.,. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
c:> page 134.
... Check the tire p re ssu re on the spare wheel im
mediately after mounting it.
... As soon as possible, have the tighten ing tor
que s
on all wheel bolts checked with a torque
wrench. The correct tightening torque is 90 ft
lbs (120 Nm).
.,. Have the flat tire replaced as soon as possib le.
@ Tips
- If you notice t hat the wheel bolts are cor
roded and diffic ult to turn wh ile changing a
tire, they should be rep laced before yo u
chec k the tightening torque.
- Drive at reduced speed until you have the
tightening torques chec ked.
- After changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure mon itor ing indicator must
be stored in the MM I
c:> page 224,
c:> page 226 .
Emergen cy as sis tanc e
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
F ig. 1 98 Changing a wheel: Removing the whee l cover
Removing
... Insert the hoo k (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
... Pull off the decorati ve w heel co ve r c:> fig. 198 .
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fi g. 199 Cha ng ing a whee l: remov ing the wheel bolt caps
Removing
.,. Push the pla st ic clip (prov ided with the vehicle
too l kit) over the wheel bolt cap until the inner
reta iners on the clip al ign with the edge of the
cover.
... Remove the cap with the pla stic clip (vehicle
too l kit)
c:>fig. 199.
Refitting
.,. Place the caps over the whee l bolts and push
them back on.
2 37
Page 241 of 274

a co ,...,
N
" N ,...,
0 00 <..:l '
~ Align the jack so tha t its arm @¢ fig. 202 en
gages in the designated lifting point in the door
s ill and the movable base ® lies flat on the
ground. The base @ must be
vertical under the
lift ing po int @ .
~ Wind the jack up further unt il the flat tire
comes off the grou nd
¢ & -
Position the vehicle jack only under the designat
ed lifting points on the
sill ¢ fig. 201 . There is ex
actly
one locat ion for each wheel. The jack must
not be positioned at any other
l ocation ¢.&.''~ ©.
An unstable surface under the jack can cause the
ve hicle to slip off the jack . Always provide a firm
base for the jack on the ground .
If necessary
p lace a sturdy boa rd or similar support under the
jack . On
hard, slippery surface s (such as tiles)
use a rubber mat o r similar to prevent the jack
from
slipping ¢.&. .
& WARNING
- Yo u or your passengers could be injured
whi le chang ing a wheel if you do not follow
these safety precautions:
- Position the veh icle jack on ly at the desig
nated lifting points and align the jack .
Othe rw ise, the vehicle jac k cou ld slip and
cause an injury if i t does n ot have suffi
cient hold on the vehicle .
- A soft or un stable s urface unde r the jack
may c ause the vehicle to slip off the jac k.
Always p rovide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack .
- O n ha rd, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and yo ur
passengers:
- Do not ra ise the vehicle unt il you are sure
the jack is securely engaged .
- Passengers must not remain in the veh icle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
Em ergen cy as sis tanc e
-Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack .
- Changes in temperature or load can affect
the height of the veh icle.
(D Note
Do not lift the ve hicle by the si ll. Position the
vehicle jack only at the des ignated lift ing
po ints on the sill. Otherw ise, your veh icle wi ll
be damaged.
(D Tips
The vehicle jack mode * switches off automati
ca lly at speeds above 6 mph (10 km/h) .
Removing and installing the sill extension
cover
Applies to: vehicles with sill extension
Fi g. 2 03 Sill: r em ov in g the cover
~ Pull the cover down to remove it ¢ fig. 203
~ To install the cover, insert it in the mount and
press it upward until it clicks into place . The
cover must be flush with the surface of the s ill
extens io n.
(D Tips
Some models may a lso have a cover for the
r ear vehicle lift po int .
239
Page 243 of 274

a co ,...,
N
" N ,...,
0 00 <.,;) '
Tires with unidirectional tr ead design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread pattern in
tended fo r use in a specific direction, please note
the following:
- The direction of rotat ion is marked by an arrow
on the side of the tire .
- If the spare tire has to be installed in the incor
rect direction, use the spare tire only tempora
rily s ince the tire will not be able to achieve its
opt imum performance character istics with re
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten
t ion to this fact during wet weather and that
you adjust your speed to match road condi
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec
tiona l tire .
Notes on wheel changing
Please read the information ~ page 212, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
- Check the tire pressure on the spare tire im
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lbs (120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque.
Emergency assistance
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble. Remount the wheel cover.
Until then , drive with extra care and at reduced
speeds.
A WARNING
- If you are going to equip your vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read the information
r=> page 212, New tires or
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart
ment and are not loose in the passenger
compa rtment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve
h icl e.
- Always store damaged wheel, jack and tools
securely in the luggage compartment. Oth
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas
sengers in the vehicle .
Spare tire
Space-saving spare tire
App lies to : vehicles wit h spare tire
Fig. 206 Luggage compartment: space-sav ing spare tire
The spare tire is intended for short-term use on-
-
ly. Have the damaged tire checked and, if neces
sary, replaced by an authorized Audi dealer or au
thorized Audi Serv ice Facility as soon as possible .
..,.
241