check engine AUDI A8 1995 D2 / 1.G AEB Engine Ignition Coil System Checking

Checking

- Check DTC memory Page 01
-15
.

There must be no malfunctions stored

- If DTC memory is not clear, make necessary
repairs and erase DTC memory, stop engine
and start engine again, road test, check and
erase DTC memory again.
Pa
ge 2 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

28-18

- By briefly disconnecting fuel injector connectors
with engine running, check which cylinder is
misfiring, or not firing at all.

Note:
A misfiring cylinder can also be isolated by
pulling the spark plug connectors (carbon-fouled
plug).

- Check spark plug connector resistance.


Specified value: approx. 2 k If resistance is NOT OK:

- Reconnect spark plug connector.

- Interchange spark plug with one from cylinder
that is OK.

- If other cylinder now misfires, replace faulty
spark plug.

- If same cylinder misfires, interchange ignition
coil with one from cylinder that is OK.

-
If other cylinder now misfires, replace faulty
Pa
ge 3 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

coil.

- If original cylinder still misfires, check secondary circuit ground
connection for open circuit between coil connector terminal 4a and
engine Ground.
- If Ground connection is OK, check:

Primary wiring and power supply Page 28
-19

Final output stage for ignition coils Page 28
-21
Pa
ge 4 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

28-19

Wiring for primary coil and power
supply, checking


Required special tools and test equipment

VAG 1527B LED voltage tester
VW 1594 connector test kit
Wiring diagrams

Test conditions
Fuse for ignition coils OK

Checking

- Disconnect 4-pin harness connector from power
output stage.

- Switch ignition on.

Note: - Connect VAG 1527B LED voltage tester in turn between 4-pin
connector terminals 1, 2, 3 and 4, and engine ground.
LED must light up for all 4 terminals
Pa
ge 5 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

28-22

Checking signal for power output stage

- Disconnect 5-pin harness connector from power
output stage.

If the LED in the tester does not blink: - Connect VAG 1527B LED voltage tester in turn between 5-pin
connector terminals 1, 2, 4 and 5, and engine ground.
- Crank starter for a few seconds in each case.
LED must blink all 4 times
- Connect VAG 1598/22 test box to ECM harness connector Page 01
-
56
.

- Check wiring for open circuit between ECM/test box and 5-pin harness
connector, according to wiring diagram.

Connector terminal 1 to ECM/test box socket 70
Connector terminal 2 to ECM/test box socket 78
Connector terminal 4 to ECM/test box socket 77
Connector terminal 5 to ECM/test box socket 71
Specified value: max. 1.5
Pa
ge 9 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

28-23
If the wiring is OK:

If the wiring is OK, but the LED in the tester did not blink: - Check for open circuit between 5-pin connector terminal 3 and engine
Ground.

Specified value: max. 1.5 - Replace Motronic ECM -J220- Page 01
-57
.
- Carry out adaptation of throttle valve control module to ECM Page
24
-119
.
- Check readiness code Page 01
-59
. If Diagnostic Trouble Code
(DTC) memory has been erased, or ECM was disconnected, generate
new readiness code Page 01
-62
.
Pa
ge 10 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2

28-24

Checking power output stage

Signals to power output stage OK Page 28
-22
.

- Disconnect 4-pin harness connector from power
output stage.

- Connect VAG 1527B LED voltage tester
between Battery Positive Voltage (B+) and, in
turn, each terminal of power output stage 4-pin
connector.

- Crank starter for a few seconds in each case.

LED must blink all 4 times
If the LED in the tester does not blink for all
terminals:

- Replace power output stage.

Note:
LED testers with very little power consumption
glow slightly before cranking the engine. During
cranking they will get brighter or darker.
Pa
ge 11 of 11 Individual i
gnition coil s
ystem, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.28.2