ECU AUDI A8 1996 D2 / 1.G 01V Transmission Remove And Install User Guide

37-107


Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version.
WARNING!
When working on the subframe, all precautions and notes which are
listed in Repair Manual, Suspension, Wheels, Steering must be
must be observed. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Before loosening carrier, special tool 3393 must be used to check
whether holes -1- and -2- line up.
- Completely lower subframe at rear and front.
Pa
ge 37 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-112

- Remove remaining connection bolts for
engine/transmission.

- Press transmission off engine, while pressing
torque converter out of drive plate.

- Press torque converter against the ATF pump (arrow).

- Rotate transmission (arrow) and carefully move into position between
subframe and vehicle floor.
- Lower transmission.
- Secure converter so it does not fall out.
Pa
ge 42 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-114


Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.
- Place transmission onto transmission support.

During this, the subframe is lowered approx. 150 mm at rear page 37
-
88
, illustration A37-0067. - Secure transmission on 3282 transmission support using bolt -A-.
- Move transmission into position between the lowered subframe and
vehicle floor.
- Align transmission properly to engine.
Pa
ge 44 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

Bolts -3- and -5- also secure a bracket for cables.
Pa
ge 51 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-130

Automatic transmission, transporting


Special tools and equipment

The 3457 attachment and holding rig can be used when transporting the
transmission and for setting up the 3282 transmission support.
3457 attachment and holding rig

- Attach the 3457 attachment and holding rig at the transmission housing
mounts and secure.
Pa
ge 62 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-132


For transmissions with Front Wheel Drive (FWD), the VW540 holding
fixture can also be used to secure the transmission to the VW313 holding
fixture. - Attach the 3457 attachment and holding rig at the transmission housing
mounts and secure.
- Bolt the attachment and holding rig to the VW 309 holding plate and
place this into the VW313 holding fixture using a workshop crane.

WARNING!
The center of gravity of the transmission is located outside the
turning center at holding fixture. To turn the transmission, a second
technician must hold the transmission housing to prevent back-
swing.
Note:
Vents for the transmission housing and final drive must be closed before
turning a filled transmission on the assembly stand so that the oil pan
faces upward . - Secure transmission to VW540 holding fixture (arrows) and insert in
VW313 holding fixture.
Pa
ge 64 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2