engine oil AUDI A8 1996 D2 / 1.G 01V Transmission Remove And Install Workshop Manual

37-79

For 6 cylinder engines except for 2.7 Liter 5V
turbo engine:

- Unclip vent hose for alternator -1-.
- Unbolt bracket for ATF line -2- at oil pan.

- Separate ATF lines -1- to ATF cooler.
- Plug ATF lines with clean plug.
- Unbolt bracket for ATF line -3-.
- Remove transmission side starter bolt -2-.
Pa
ge 9 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-95

- Only perform vehicle alignment if necessary.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 44; Vehicle alignment


- Install transmission supports at left and right with
transmission mount page 37
-125


Bolt torque converter to drive plate
For vehicles with hex bolts: - Remove bolt -A- after transmission is bolted to engine.
- Apply corrosion protection to contact surface between bolt -A- and oil
pan.

- Bolt torque converter to drive plate via 3 bolts using special tool V175
(turn crank shaft an additional 1/3 turn every time).
Pa
ge 25 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-117


Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing

Repair Manual, Suspension, Wheels, Steering, Repair Group 44,
Vehicle alignment
- Install bolts of torque converter through opening -A- in engine flange to
the drive plate (turn crankshaft 1/3 rotation each time).
- Insert plug into opening -A- in engine flange.
- Install subframe, observe tightening sequence and alignment with
master hole.
- Only perform vehicle alignment if necessary.- Install transmission supports at left and right with transmission mount
page 37
-125


- Remove bolt -A- after transmission is bolted to engine.
- Apply corrosion protection to contact surface between bolt -A- and oil
pan.
- Bolt on ATF lines page 37
-149
Pa
ge 47 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-119

Tightening torques


Notes:

Tightening torques are valid only for nuts and
bolts that are lightly greased, oiled, covered
with a thin coat of phosphate or blackened.
Other lubricants are permitted, e.g. engine oil or
transmission fluid, however they may not
contain graphite.
Do not use any degreased parts.

Engine/transmission mount for 4 cylinder engines (5 valve, turbo) 1) With nut
Item A = bushings Item no.
Bolt
Nm
1, 8, 9, 10 M10 X 45 45
2, 3, 4, 11 M12 X 67 65
5 M12 x 110 65
6 M12 x 90 65
7
1)
M10 x 60 45
Pa
ge 50 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2