transmission AUDI A8 1997 D2 / 1.G ATQ Engine Readiness Code Workshop Manual

01-82

Readiness code, generating


Special Tools and Equipment

Requirements
Note:
If, during a work step, the test result is indicated as "OK" immediately after
selecting a display group, the test has already been carried out and it is
OK to continue on to the next work step.
VAG1788/10 RPM adjusterElectrical consumers switched off (radiator fan must NOT run during
test). A/C system switched on. Vehicles with automatic transmission Selector lever in P or N. Coolant temperature at least 80 C Display group 4, display field
3. Important: Drive engine warm via road test if possible.
Pa
ge 8 of 47 Readiness code
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.7

01-89

Work step 5: Check operating condition of
oxygen sensor control

- Start engine (for a vehicle with manual
transmission: engage clutch).

Note:
After starting engine, it may be necessary to
select the Engine Control Module (ECM) again
using "address word" 01 and the function "Initiate
basic setting" using "04".

- Install VAG1788/10 RPM adjuster on the
accelerator pedal and raise the engine speed.


Specification: 2200 RPM
Basic Settin
g
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -3- and -0- to select "display group number 030" and
press -Q- button to confirm input.
System in Basic Setting 30
1
2
3
4

When indicated on display:
Note:
A few minutes may pass until a diagnostic result is reached. - Check oxygen sensor status in display fields 1 to 4.
Pa
ge 17 of 47 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.7

01-103


Display fields

1 2 3 4
Display group 046: Diagnostic of catalytic converter (bank 1)
Display xxxx/min
xxx C
x.x s
---
Indicated Engine
speed
(RPM) Exhaust
temperature Catalytic
converter -
conversion Diagnostic condition
Functional
range 630 to 6800
RPM 70 to 850 C
0.00 to 0.99 Test OFF
Test ON
Cat B1 OK
Cat B1 not OK
Specified
value 2200 RPM
above 420 C 0.00 to 0.52

1)

0.00 to 0.47

2)
Cat B1 OK
Notes



If "Cat B1 not OK" is displayed: Check Diagnostic
Trouble Code (DTC) memory Page 01
-15
. If no DTCs
are stored, replace catalytic converter.
1) Manual transmission 2) Automatic transmission
Pa
ge 35 of 47 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.7

01-105


Display fields

1 2 3 4
Display group 047: Diagnostic of catalytic converter (bank 2)
Display xxxx/min
xxx C
x.x s
---
Indicated Engine
speed
(RPM) Exhaust
temperature Catalytic
converter -
conversion Diagnostic condition
Functional
range 630 to 6800
RPM 70 to 850 C
0.00 to 0.99 Test OFF
Test ON
Cat B2 OK
Cat B2 not OK
Specified
value 2200 RPM
above 420 C 0.00 to 0.52

1)

0.00 to 0.47

2)
Cat B2 OK
Notes



If "Cat B2 not OK" is displayed: Check Diagnostic
Trouble Code (DTC) memory Page 01
-15
. If no DTCs
are stored, replace catalytic converter.
1) Manual transmission 2) Automatic transmission
Pa
ge 37 of 47 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.7