transmission AUDI A8 1998 D2 / 1.G 01V Transmission Select Lever Mechanism User Guide

37-46

Adjusting

Selector lever cable has been loosened from
lever/shift rod.

- Shift selector lever into position "P".

- Shift lever/shift rod to "P", parking lock must
engage, both front wheels cannot be turned in
one direction.

- Loosen mounting bolts (arrows) of bracket at transmission.
- Press selector lever cable onto lever/shift rod.
- Align selector lever cable in bracket.
- Tighten mounting bolts (arrows) of bracket at transmission to 23 Nm.
- Install shielding plate/selector lever cable
- Check shift mechanism page 37
-2 .
Pa
ge 51 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-55


Repair Manual, 5 Spd. Automatic Transmission
01V On Board Diagnostic (OBD), Repair Group 01; On Board Diagnostic (OBD); Read measuring value block
10 -
Locking cable lever
11 -
Shift lock solenoid -N110-
Removing and installing Fig. 3
, page
37
-61

Unclip connector from wiring harness (at
center console) item , page 37
-61

Can be checked via electrical test and read
measuring value block
12 -
Spring bracket
Insert both ends into selector lever
13 -
Locking segment Insert into selector lever together with
spring bracket
Pa
ge 60 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-56


14 -
Cover
For shift mechanism housingRemoving and installing Fig. 1
, page
37
-59

15 -
Locking clamp
For selector lever cable to selector lever
16 -
Locking plate For selector lever cable to shift mechanism
housing Fig. 2
, page 37
-60
item E
17 -
Clip
For selector lever cable to transmission
shift lever
18 -
Hex-bolt, 23 Nm
19 -
Hex-bolt, 23 Nm
20 -
Pivot For selector lever cable at transmission
Pa
ge 61 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-63

- Pull selector lever cable out of shift mechanism
housing.

- Remove shielding plate for selector lever cable
(item B).

Installing - Press retaining clip off of lever/shift lever (item C).
- Press ball socket of selector lever cable off of lever/shift rod.
- Loosen bracket from transmission (item D).
- If necessary, loosen selector lever cable from bracket (item E).
- Selector lever and lever/shift rod in position "P" (park lock must
engage).
- Installation is the reverse order of removal.
- Lightly grease coupling ring and ball socket of selector lever cable.
- Selector lever cable, checking and adjusting page 37
-45
.Pa
ge 68 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-64

Tightening torques:

Components
Tightening
torques
Selector lever cable to
mounting bracket 12 Nm
Bracket to right transmission
mount 23 Nm
Shielding plate to
transmission, M8 23 Nm

Fig. 1 Installing securing plate
- Installation of the securing plate (item E).
Insert with angled end toward rear.
Pa
ge 69 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-66

Adjusting

- Place selector lever in position "P".

- Shift lever/shift lever to "P" (last position, shift
lock solenoid must engage).

- Slightly loosen mounting bolt at bracket to transmission.
Check freedom of stress of selector lever cable, if necessary
eliminate stress.
- Tighten mounting bolt of bracket to 23 Nm.
- Check shift mechanism page 37
-2 .
Pa
ge 71 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1