key AUDI A8 1998 D2 / 1.G 01V Transmission Select Lever Mechanism Workshop Manual

37-1


Selector lever mechanism,
servicing

WARNING!

Shift selector lever into position "P" and
engage parking brake before working with the
engine running.

Notes:

Lubricate bearing areas and slide surfaces with
polycarbamide grease G 052 142 A2.
Center console must be removed for service
work:

Ignition key removal lock, checking


- Switch ignition key to driving position (ignition
on).

- Depress brake pedal and hold.

Shifting selector lever out of position "P"
must be possible with the button at shift lever
depressed without "sticking".
It must not be possible to remove ignition
Pa
ge 1 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

key with selector lever in any position other
than "P".

- Shift selector lever into position "P".
It must be possible to move ignition key into
removal position without "sticking".

- Remove ignition key.
Selector lever cannot be shifted out of
position "P" with the button pressed and foot
brake operated.
Pa
ge 2 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-10

- Attach cover.

All-wheel-drive vehicles
Continuation for all vehicles
Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system. - Tighten nuts (arrows, 4 pieces) to 10 Nm.
- Check adjustment of selector lever cable and adjust if necessary
page 37
-45
.
- Ignition key removal lock, checking page 37
-1 .
- Bolt driveshaft to transmission flange page 39
-79
, Driveshaft,
removing and installing.
- Install heat shield.
- Connecting front exhaust pipe to rear exhaust system.- Installing shift mechanism cover page 37
-24
.
- Selector lever handle, installing page 37
-22
.
- Connect battery Ground (GND) strap.
- For vehicles equipped with coded anti-theft radio, activate code.
- Check shift mechanism page 37
-2 .
Pa
ge 13 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-19


29 -
Cable ties
For locking cable
30 -
Ignition/Starter Switch
31 -
Locking cable For ignition key removal lockMust not be kinkedRemoving and installing page 37
-47
Adjusting page 37
-50
32 -
Catch lever
For ignition key removal lockRemoving and installing Page 37
-32

onward
Pa
ge 22 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-48


Repair Manual, Body Interior, Repair Group 69;
Airbag; Steering wheel, removing and installing
- Remove steering wheel.
- Switch ignition key to driving position (ignition
on).
- Shift selector lever into position "P".
- Lift up retaining clip of interlock lever -1- and pull
locking cable out of ignition/starter switch.
- Remove cover with guide (selector lever
mechanism) page 37
-5 .
- Unclip locking cable from securing spring at shift
mechanism housing, slightly lift up securing
spring to do so Fig. 1
, page 37
-21
.
- Loosen and remove locking cable from cable tie
-2-.
Pa
ge 53 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-49


Installing
- Route locking cable without kinking.
- Switch ignition key to driving position (ignition
on).
- Insert locking cable into ignition/starter switch.
- Check locking mechanism of interior lever -1-.
- Secure locking cable to airbag sensor using
cable tie -2-.
- Bring ignition/starter switch into locking position
(ignition off).
- Shift selector lever into position "P".
- Clip locking cable into securing spring of shift
mechanism housing Fig. 1
, page 37
-21
.
- Hook locking cable bracket -3- into shift
mechanism and locking coupling ring in lever (for
locking cable).
Pa
ge 54 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-50


Adjusting
- Shift selector lever into position "P".
- Loosen bolt -6-.
- It must be possible to slide bracket -3- in
direction of arrow -5-.
- Adjust steering column downward.
- Connect 3352 A adjustment pin for shift lock 3 -
item 4- between lever (for locking cable) and
locking coupling ring.
- Pull locking cable in direction of arrow -5- and
tighten bolt -6- to 10 Nm.
- Remove adjusting gauge.
- Check ignition key removal lock after every
adjustment of the locking cable page 37
-1 .
Pa
ge 55 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1