wiring AUDI A8 1999 D2 / 1.G 01V Transmission Electrical Testing Owner's Manual

01-295

Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
23 A) 40 + 28
3)
40 + 34 Wiring to ECM (engine
RPM signal)
Ignition
switched off
- ECM
disconnected 15 - 80 K
- Check wiring per wiring diagram.
- Check on-board computer.

40 + xx
2)
less than 1.5

Repair Manual, Electrical
Equipment, Repair Group 01

24 A) 20 + 28
3)
20 + 34
20 + 55
20 + 26 Wiring to ECM (torque
reduction)
Ignition
switched off
- ECM
disconnected infinite
1)
- Check wiring per wiring diagram.

20 + xx
2)
less than 1.5


1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Corresponding terminal assignment at Engine Control Module (ECM).
Pa
ge 36 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

Electrical Wiring Diagrams & Component Locations binder A) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-Bus

Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, aggregate allocation, ratios, equipment

3) Pin 28 at the control module is vacant for vehicles with 10-pin connector of multi-function switch -F125-.
Pa
ge 37 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-296

Resistance measurement: switch multimeter to 2 M measuring range
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional steps Specified
value Corrective action
25 A) 51 + 28
3)
51 + 34
51 + 55
51 + 26 Wiring to ECM (upshift/downshift
signal)
Ignition switched
off
- ECM
disconnected infinite
1)
- Check wiring per wiring
diagram.

51 + xx
2)
less than 1.5


1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Corresponding terminal assignment at Engine Control Module (ECM).

Electrical Wiring Diagrams & Component Locations A) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-Bus

Pa
ge 38 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-297

Voltage measurement: switch multimeter to 20 V measuring range
Test
step VAG
1598/20sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
26 13 + 34
13 + 6 Tiptronic
switch -
F189- Ignition switched
on
- Selector lever in D
but not in tiptronic gateapprox. 10
V - Check wiring according to wiring
diagram.
Ignition switched
on
- Selector lever
tiptronic gate approx. 20
mV
Repair Manual, 5 Spd. Automatic
Transmission 01V, Repair Group 38
- Check magnet on lateral gate cover
1)
- Repair shift mechanism, if necessary
replace gate cover or circuit board with
Tiptronic switch -F189
1)
- Perform test step 29
1) The Tiptronic Switch -F189- receives its tiptronic gate recognition information or tiptronic up- and down-shift information via
the large magnet which is mounted on the lateral gate cover of the gate cover. If the switch has become detached, the gate
cover must be replaced.
Pa
ge 40 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-298

Voltage measurement: switch multimeter to 20 V measuring range
Test step
VAG
1598/20sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
27
46 + 54
46 + 55 Tiptronic
Switch -
F189- Ignition switched off
- Selector lever in
Tiptronic gate less than
1.5V With the Tiptronic Switch the driver
can manually select the desired
driving range
2)

Ignition switched on
- Selector lever in
Tiptronic gate and up-
shift switch actuated approx.
battery
voltage - Check wiring according to wiring
diagram. If installed also check
wiring to Tiptronic steering wheel

46 + 34
46 + 6 Ignition switched on
- Selector lever in D
- Selector lever in
Tiptronic gate
- Selector lever in
Tiptronic gate and
downshift switch
activated approx. 12V
Repair Manual, T5 Spd.
Automatic Transmission 01V, Repair Group 37
- Check magnet on lateral gate
cover
1)
- Repair shift mechanism, if
necessary replace gate cover or
circuit board with Tiptronic switch -
F189- 1)
Continued


Ignition switched on
- Selector lever in approx.
15mV - Perform test step 28
Pa
ge 41 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-299

Voltage measurement: switch multimeter to 20 V measuring range
Test step
VAG1598/20sockets
Test of
Test conditions
- Additional stepsSpecified
value Corrective action
27
cont'd 47 + 34
47 + 6 Tiptronic
Switch -
F189- Ignition switched on
- Selector lever in D
- Selector lever in
Tiptronic gate
- Selector lever in
Tiptronic gate and up -
shift switch activated approx. 12V With the Tiptronic Switch the
driver can manually select the
desired driving range
2)
- Check wiring according to
wiring diagram. If installed also
check wiring to Tiptronic
steering wheel

Ignition switched on
- Selector lever in
Tiptronic gate and
down-shift switch
activated approx.15
mV - Check magnet on lateral gate
cover
1)

46 + 54
47 + 55
Ignition switched off
- Selector lever in
Tiptronic gate less than
1.5V - Repair shift mechanism, if
necessary replace gate cover
or circuit board with Tiptronic
switch -F189-
1)
Continued



Ignition switched off
- Selector lever in
Tiptronic gate and approx.
battery
voltage Repair Manual, 5 Spd.
Automatic Transmission 01V, Repair Group 37

Pa
ge 43 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-301

Resistance measurement
Test
step VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
28 A) 85 + 28
3)
85 + 34
86 + 28 3)
86 + 34 Wiring connection of TCM to
ECM (CAN-bus)
Ignition switched
off ECM
disconnected infinite
1)
- Check wiring per wiring
diagram.

85 + xx
2)
86 + xx 2)
less than 1.5

Further information on CAN-bus
page 01
-263

1) Switch VAG1526 to highest resistance ( ) measuring range. 2) Applicable terminal assignment at Engine Control Module (ECM).

Repair Manual, Fuel Injection & Ignition, Repair Group 24
Pa
ge 46 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-302

Wiring between transmission and 88-pin
connector for Transmission Control
Module (TCM) -J217-, testing


Perform if:

Output Diagnostic Test Mode (DTM) or
Electrical test indicates malfunctions in the
transmission, the TCM -J217-, or in the
corresponding wiring.

Test conditions
Ignition switched off
Connect VAG1598/20 adapter only to 88-pin
connector of transmission wiring harness.
Perform measurements with VAG1598/20
adapter on the outside of the vehicle

- Remove noise insulation panel.
- Remove bracket -1- for noise insulation panel.
Pa
ge 48 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-303

Wiring to 16-pin connector on transmission,
testing

- Turn 16-pin connector -4- on transmission to release bayonet catch.

- Use multimeter (Fluke 83 or equivalent) to test for continuity between
terminals of 16-pin connector and sockets on VAG1598/20 adapter.
Resistance specifications table, page 01
-304
.
Pa
ge 49 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-304
Resistance specifications
Terminal on
16-pin connector Socket on VAG1598/20
adapter Specification
Corrective action
1 42
1.5
Check connectors for: - Repair open circuit according to current wiring diagram.
- contact corrosion
- ingress of water
- leaks
2 5
1.5
3 1
1.5
4 32
1.5
5 16
1.5
6 44
1.5
7 29
1.5
8 30
1.5
9 33
1.5
10 14
1.5
11 4
1.5
Pa
ge 50 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16