ECU AUDI A8 2000 D2 / 1.G 01V Transmission Select Lever Mechanism User Guide

37-37


Pivot pin can have a maximum of 4 center punch marks. - Slide link -B- with Tiptronic spring mechanism into selector lever -A-
with pull-lever -D- raised.
- Drive pivot pin -C- into selector lever using a drift page 37
-36
,
illustration N37-0524.
-
To secure, make two new center punch marks (arrows) offset by 90 to
the existing ones. - Install selector lever page 37
-34
.
Pa
ge 42 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-41

All-wheel-drive vehicles

Continuation for all vehicles - Unbolt driveshaft -1- from transmission and let rest on heat shield -2-
page 39
-79
, Driveshaft, removing and installing.
- Secure driveshaft using wire (arrow) at bracket -3- of fuel lines.
- Unbolt heat shield from below shift mechanism housing.

- Remove cover from shift mechanism housing (arrows).
Pa
ge 46 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-42
Disconnect selector lever cable from shift
mechanism housing:

- Press ends of locking clip -B- together and remove.
- Remove securing plate -A- for selector lever cable at shift mechanism
downward.
- Remove selector lever cable from selector lever.

Installing - Pry off selector lever cable from lever/shift rod using 80-200 pry lever
(arrow).
- Remove bracket from transmission.
- Loosen selector lever cable from bracket.
- Pull selector lever cable out of shift mechanism housing without
kinking.
Selector lever and lever/shift rod in position "P" (park lock must
engage).
- Do not bend or kink selector lever cable, lightly grease coupling ring
and ball socket before installing
Pa
ge 47 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-43

- Guide selector lever cable into shift mechanism
housing.

- Connect selector lever cable to selector lever.

Installation position:
Angled end of securing plate points toward the end of the selector lever
cable. - Press ends of locking clip -B- together and secure selector lever cable.
- Install securing plate -A- for selector lever cable to shift mechanism.
- Connect selector lever cable to bracket by hand.
- Bolt bracket to transmission by hand.
- Press selector lever cable onto lever/shift rod.
- Align selector lever cable in bracket.

- Tighten bracket/transmission (arrows 1) and selector lever
cable/bracket (arrow 2) to tightening torque. During this, counterhold at
hex socket (arrow 3).
Pa
ge 48 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-48


Repair Manual, Body Interior, Repair Group 69;
Airbag; Steering wheel, removing and installing
- Remove steering wheel.
- Switch ignition key to driving position (ignition
on).
- Shift selector lever into position "P".
- Lift up retaining clip of interlock lever -1- and pull
locking cable out of ignition/starter switch.
- Remove cover with guide (selector lever
mechanism) page 37
-5 .
- Unclip locking cable from securing spring at shift
mechanism housing, slightly lift up securing
spring to do so Fig. 1
, page 37
-21
.
- Loosen and remove locking cable from cable tie
-2-.
Pa
ge 53 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-49


Installing
- Route locking cable without kinking.
- Switch ignition key to driving position (ignition
on).
- Insert locking cable into ignition/starter switch.
- Check locking mechanism of interior lever -1-.
- Secure locking cable to airbag sensor using
cable tie -2-.
- Bring ignition/starter switch into locking position
(ignition off).
- Shift selector lever into position "P".
- Clip locking cable into securing spring of shift
mechanism housing Fig. 1
, page 37
-21
.
- Hook locking cable bracket -3- into shift
mechanism and locking coupling ring in lever (for
locking cable).
Pa
ge 54 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-60


Note: Fig. 2 Shift mechanism housing, removing and installing
- Remove bottom shielding plate and catalytic converter.
- Disconnect selector lever cable from shift mechanism housing.
- Before installing, secure rubber housing -A- to shift mechanism
housing.
- Tighten nut - 9 Nm
Rubber housing -A- must seal shift mechanism housing to chassis
(sealing lip -B-). Do not rout any cables between chassis and mounting bracket.
Pa
ge 65 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-61


Fig. 3 Shift Lock Solenoid -N110-, removing and installing
- Unclip connector -D- (console wiring harness).
-
Turn lift solenoid in direction of arrow approx. 90 .- Check shift mechanism after removing lift solenoid page 37
-2

Fig. 4 Route wire for base illumination
- Route wire for base illumination below guide and secure in notch -A-
(left/right).
- Clip connector -B- in bracket onto guide.
- Clip in wiring harness connector (console).
Pa
ge 66 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-62

Selector lever cable for shift mechanism
(without Tiptronic), removing and
installing


Note:

Do not bend or kink selector lever cable, lightly
grease coupling ring and coupling ends before
installing
Selector lever cable can best be removed in
selector lever position "P".

Removing:

- Remove shielding plate (below shift mechanism)
for exhaust system.

- Remove cover:
Disengage snap lock of cover by pressing in direction of arrow A
page 37
-59
.
- Disengage locking clip by pressing both ends together and pull selector
lever cable off selector lever.
- Pull out securing plate for selector lever cable at shift mechanism
housing downward.
- Insert with angled end toward the rear and in groove at selector lever
cable Fig. 1
, page 37
-64
.
Pa
ge 67 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-64

Tightening torques:

Components
Tightening
torques
Selector lever cable to
mounting bracket 12 Nm
Bracket to right transmission
mount 23 Nm
Shielding plate to
transmission, M8 23 Nm

Fig. 1 Installing securing plate
- Installation of the securing plate (item E).
Insert with angled end toward rear.
Pa
ge 69 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1