battery AUDI A8 2012 User Guide

- The buttons for the power sun shades* in
the side windows,
- The buttons for the power sun shade* in the
rear window,
- Front passenger power seat adj ustment *
button.
_& WARNING
- When you leave your vehicle -even if on­
ly briefly- always take the ignition key
with you. This applies particularly when
children remain in the veh icle. Otherw ise
the ch ildren could start the engine or op­
erate electrical equ ipment (e.g. power
w indows) . The power windows are func­
t ional until t he driver's door or passeng­
er's door has been opened.
- Be careful when closing the windows.
Check to see that no one is in the way, or
serious injury could result!
- When lo cking the veh icle from outside,
t he ve hicle must be unocc upied s in ce the
w indows can no longer be opened in an
emergency.
(D Tips
- The dr iver can lower or raise the power
sun shades * in the side windows by us ing
swi tches © and
@.
-After the ignition has been switched off,
the windows can still be opened o r
closed for about 10 minutes . The powe r
windows are not switched off until the
driver's door or passenger's door has
been opened.
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery hos been discon ­
nected.
• Pull and hold the power window switch un­
ti l the window is fully closed.
• Release the switch and then pull it again for
at least one second .
Openin g an d clos ing 39
Valet parking
The valet parking feature protects the lug­
gage comportment from unauthorized ac­
cess.
F ig. 30 Valet par king button
Wi th "valet parking" a ctivated, the rear lid
cannot be opened.
• Remove the mechanical key
c::;, page 29 .
• Open the glove compartment and activate
c::;, fig. 30 the "valet parking" feature by
pressing the
! VALET I b utton. The indicator
light in the swi tch illuminates.
• Close the glove compartment and lock it
w ith the mechanical key.
• Leave the master key with the se rvice per ­
sonnel for park ing and keep the mechanical
key with you.
When the "valet parking" feature is activated:
- the unlocki ng button fo r the rear l id
c:s in
the dr ive r's door is inactive
- the button
c:s on the mas ter key is inac tive
- the opening handle in the rear lid is inact ive .
The vehicle can be driven and locked and un­
locked with the master key. Access to the lug­
gage compartment is blocked.
When the valet parking function is switched
on, the message
Vale t par king acti vated ap­
pears in the instrument cluster display when
you sw itch the ignition on.

70 Seats and storage
-Never exceed the maximum permissible
load carrying capacity of the roof of your
vehicle, the permissible axle weights and
the permissible total weight of your vehi­ cle
c::, page 276, Weights .
@ For the sake of the environment
As a result of the increased wind resist­
ance created by a roof rack, your vehicle is
using fuel unnecessarily. So remove the
roof rack after using it.
12-volt sockets
Applies to vehicles: 12-volt soc kets
Electrical accessories can be connected to ev­
ery 12-volt socket.
Fig. 71 Sect io n of the trim panel of th e lu ggage com­
part ment: 12 -vol t soc ket
Fig. 72 Rear center conso le: 12-vo lt soc ket
... Open the socket cover c::, fig. 71 or c::, fig. 72 .
... Insert the plug of the electrical device into
the socket.
There is an additional 12 volt socket in the
front center console~
page 71, fig. 73.
The 12 volt sockets may be used for 12-volt
appliances with maximum consumption of up
to 100 watts . Before you purchase any accessories, always
read and follow
the information in
c::, page 282, Additional accessories and parts
replacemen t.
A WARNING
The sockets and the electrical accessories
connected to them operate only when the ignition is switched on . Incorrect usage
can lead to serious injuries or burns. To re­
duce the risk of injuries , never leave chil­
dren unattended in the vehicle with the ve­
hicle key.
(D Note
To avoid damaging the socket, only use plugs that fit properly.
- Never connect equipment that generates
electrical current, such as a solar panel
or battery charger, to the 12 volt socket .
This could damage the vehicle 's electri­
cal system.
- The 12 volt socket should only be used
for a short period of ti me as a power
source for electrical equipment. Please
use the electrical sockets in the vehicle
when connecting equipment for longer periods.
@ Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained.

- the temperature in the luggage compart­
ment is below 131 °f (55 °C). The cooler
switches off automatically if the tempera­
ture in the luggage compartment exceeds
131 °f (55 °C) . Once the temperature falls
below 131 °f (55 °C) again, the cooler
switches on aga in automatically .
- the battery is adequately charged . The cool­
er switches off automatically if the vehicle
battery voltage falls below a minimum lev­
el. This prevents the battery from discha rg­
i ng . The cooler switches back on again auto­
matically when the battery voltage increases
again (e.g . after starting the engine).
The cooler cools to 42.8 °f
(+ 6 °C) and the
freezer cools to 21.2 °f (-6 °C) in opt imum
cooling cond itions . Th e cooling performance
is affected by the temperature in the luggage
compartment. The temperature inside the
cooler will be higher if the luggage compart­
ment is hot.
A WARNING
To avoid putting the occupants at any risk,
please observe the following safety rules:
- The maximum capacity is 2.5 kg (5.5
lbs.).
- Never overload the cooler. This could
cause injury in the event of a collision or
sudden braking.
- The coo ler lid must always be kept closed
while you are driving. Make sure the re­
taining catch is securely engaged. The
contents of the coo ler could be thrown
forward into the passenger compart­
ment in the event of a collision or under
sudden braking - risk of injury!
- Inflammable liquids, gas canisters, etc.
must not be stored in the cooler -risk of
exp losion! This also includes any prod­
ucts that might emit volatile or inflam­
mable gases.
- Liquids will freeze at temperatures at or
below 32 °f (0 °C) and may cause glass
bottles to burst!
Seats and storage 73
(D Note
-The venti lation openings for the cooler
are located on the back pane l trim in the
luggage compartment and
must be kept
clear at all t imes.
- If the cooler is not functioning properly,
switch it off to prevent further damage.
Have it checked by a qualified workshop .
Operation
Applies to vehicles: wit h coo ler
Fig. 76 Rea r ce nte r armre st
The cooler is located in the rear cabin behind
the center armrest or behind the sliding cover (depending on the equipment fitted in your
vehicle) . The cooler and freezer only work
when the ignition is on .
Opening / closing the cooler
.,. To open the cooler, pull the release lever@
~ fig. 76.
.,. To close the cooler, push the lid back into its
original position. You should hear the re­
lease lever
(D engage if the lid is properly
closed.
Switching on /off
.,. Press button @ 9 fig. 76 to sw itch the cool­
er on/off. The symbol in the button is lit
when this function is activated .
.,. Press button
@ to switch the freezer on/
off . The symbol in the button is lit when this
function is activated .

CD Note
-Avoid high engine rpm, fu ll throttle and
heavy engine loads unti l the engine has
reached operating temperature -other ­
wise you risk engine damage.
- T he engine cannot be started by pushing
or towing the veh icle.
- If the engine has been under heavy load
for an extended period, heat builds up in
the engine compartment after the en­
gine is switched off -there is a risk of
damag ing the engine . Allow the eng ine
to run at idle for about 2 m inutes befo re
swit ching it off.
@ Tips
- If you open the dr iver's door w ith the ig­
nit ion on, a buzzer sounds and the mes­
sage
Igniti on i s on appears in the instru­
ment cluster disp lay. Switch the ign it ion
off .
-If you leave the vehicle with the ignit ion
swi tched on, the ignition will switch off
after a certain period of time. Please
note that e lectrica l equipment such as
exter ior lights wi ll switch off as well
when that happens .
Stopping the engine
... Bring your vehicle to a comple te stop .
... Move the selector lever to the P or N posi ­
t ion .
... Press the !START E NGIN E STOPI button
Q page 80, fig. 81 .
Emergen cy off
If necessary, the engine can be swi tched off
with the selector lever in the R, Dor S posi ­
tions . The eng ine stops if you press the
I START E NGIN E STOP I button at speeds be low
6 mph (10 km/h).
_& WARNING
- Never turn off the eng ine unt il the vehi­
cle has come to a complete stop.
On th e road 81
- The brake booster and power steering
only work when the engine is running. If
the engine is off, you have to use more
force when steering or braking . Because
you cannot s teer and brake as you usual­
ly would, th is could lead to crashes and
serious injuries.
- For safety reasons , you sho uld a lways
park your vehicle with the selector lever
in P . Otherwise, the vehicle could inad­
vertently roll away.
- After the eng ine has been switched off,
the radiator fan can cont in ue to run for
up to 10 minutes -even with the igni tion
switched off .
It can also switch on again
after some time if the coolant tempera­
ture rises as the result of a heat b uildup
or if the engine is hot and the engine
compartment is additionally heated by
the sun's rays .
~
CD Note
Do not stop the eng ine immediately after
hard or extended driving. Keep the engine
running for approximate ly two minutes to
prevent excess ive heat bu ild -up .
Starting the engine if there is a
malfunction
It may not be possible to start the engine un­
der certain circumstances , for example if the
battery in the vehicle key is drained, if inter ­
ference is affected the key or if there is a sys­
tem malfunction.
ij
:c
---- -~
Fig . 82 Center co nsole/m aste r key : star ting the engine
I
if th ere is a malfun ction Ill>

102 Audi side assist
- Side assist is not active wh ile you are
making the adjus tment.
- Your settings are automatica lly sto red
and ass igned to the remote control key
being used.
Driver messages
App lies to vehicles: with side assist
If side ass ist switches off by itse lf, t he LED in
the butto n tur ns off a nd a message will ap­
pea r in the instr ume nt cl uster d is p lay:
Audi side assist : Currently unavailable. No
sensor vision
The radar se nsors' vision is affected. Do not
cover the area in front of the senso rs wi th bike
wheels, stickers, dirt or other objects. Clean
the area in front of the sensors, if necessary
c::;, page 100, fig. 104 .
Audi side assist : Currently unavailable
Side assis t ca nno t be swi tched o n tem porar ily
beca use there is a mal function (for exam ple,
the battery cha rge leve l may be too low) .
Audi side assist: System fault!
The system cannot guara ntee that it w ill de­
t e ct ve hicl es co rrec tly a nd it is sw itche d off .
The senso rs have been displaced o r a re faulty.
H ave the sy stem che cke d by an au thor ized A u­
di d eal er o r aut horiz ed Au di Servi ce Fa cili ty
s o on.
Audi side assist : Unavailable when towing .
Side assist switches off aut omatically whe n a
factory -insta lled trailer h itch is connected to
the el ectrical connector on the trailer. There is
no guara ntee the system will switc h off whe n
usi ng a retrofi tt ed traile r h itch . Do not use
side assis t when towing a tra iler .

156 Airbag system
airbag system and prevent that system from
working properly in a collision.
There are some important things you have to know to make sure that the effectiveness of
the system will not be impaired and that dis­
carded components do not cause injury or pol­
lute the environment.
.&_ WARNING
Improper care, servicing and repair proce­
dures can increase the risk of personal in­
jury and death by preventing an airbag
from deploying when needed or deploying an airbag unexpectedly:
- Never cover, obstruct, or change the steering wheel horn pad or airbag cover
or the instrument panel or modify them
in any way.
- Never attach any objects such as cup
holders or telephone mountings to the
surfaces covering the airbag units.
- For cleaning the horn pad or instrument
panel, use only a soft, dry cloth or one
moi5tened with plain water. Solvent5 or
cleaners could damage the airbag cover
or change the stiffness or strength of the
material so that the airbag cannot de­
ploy and protect properly.
- Never repair, adjust, or change any parts
of the airbag system.
- All work on the steering wheel, instru­
ment panel, front seats or electrical sys­
tem (including the installation of audio
equipment, cellular telephones and CB
radios, etc .) must be performed by a
qualified technician who has the training
and special equipment necessary.
- For any work on the airbag system, we
strongly recommend that you see your authorized Audi dealer or qualified work­
shop.
- Never modify the front bumper or parts
of the vehicle body.
-Always make sure that the side airbag
can inflate without interference:
- Never install seat covers or replace­
ment upholstery over the front seat- backs that have not been specifically
approved by Audi.
- Never use additional seat cushions that
cover the areas where the side airbags
inflate.
- Damage to the original seat covers or
to the seam in the area of the side air­
bag module must always be repaired
immediately by an authorized Audi
dealer.
- The airbag system can be activated only
once . After an airbag has inflated, it
must be replaced by an authorized Audi
dealer or qualified technician who has
the technical information, training and
special equipment necessary.
- The airbag system can be deployed only
once. After an airbag has been deployed,
it must be replaced with new replace­
ment parts designed and approved espe­
cially for your Audi model version. Re­
placement of complete airbag systems
or airbag components must be per­
formed by qualified workshops only. Make sure that any airbag service action
is entered in your Audi Warranty
& Main­
tenance booklet under
AIRBAG REPLACE­
MENT RECORD.
- For safety reasons in severe accidents,
the alternator and starter are separated
from the vehicle battery with a pyrotech­
nic circuit interrupter.
- Work on the pyrotechnic circuit inter­ rupter must only be performed by a
qualified dealer - risk of an accident!
- If the vehicle or the circuit interrupter
is scrapped, all applicable safety pre­
cautions must be followed.
® For the sake of the environment
Undeployed airbag modules and preten­
sioners might be classified as Perchlorate Material - special handling may apply, see
www .dtsc .ca.gov/hazardouswaste/per-
ch lo rate. When the vehicle or parts of the
restraint system including airbag modules
and safety belts with pretensioners are
scrapped, all applicable laws and .,.

192 Intelligent technology
be advisable to mount winter tires (or all-sea­
son ti res) for improved driveability and brak­
ing: these t ires must be mounted on
all four
w heels .
See also c> page 250, Winter tires.
Snow chains
Where snow cha ins are mandatory on certa in
roads, this normally a lso applies to vehicles
with A ll Wheel Driver=:>
page 251, Snow
chains.
Replacing wheels /t ire s
Vehicles w it h All Wheel Dr ive must always
have tires of the same size . Also avoid tires
with different tread depths. For details see
page
c> page 246, New tires and replacing
tires and wheels.
Off-Road driv ing?
Your Audi does not have enough ground clear ­
ance to be used as an off -road vehicle.
It is
therefore best to avoid rough tracks and un ­
even terrain as much as possible. Also refe r to
i=>page 195.
A WARNING
Always adjust your driving to road and traf­
fic condit ions. Do not let the extra safety
afforded by All Whee l Drive tempt you into
taking extra risks.
-Although the All Whee l Drive is very ef­
fective, a lways remember that b raking
capacity is limited by t ire traction. You
should the refore not dr ive at excessive
speeds on icy or slippery road su rf a ces.
- On wet road su rfaces, be careful not to
dr ive t oo fast becau se t he front wheels
co uld beg in to s lide on top of the wa ter
(aquaplaning) .
If this should occ ur, you
wi ll have no warning from a sudden in­
crease in engine speed as with a front­
wheel drive vehicle. A lways drive at
speeds wh ic h are suited to the road con­
ditions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting the engine.
If a vehicle with a conventiona l energy system
is not driven for a long per iod of t ime, t he bat­
te ry is discharged by idling current consume rs
(e.g. immobili ze r). In certa in circumstan ces it
ca n res ult in the re be ing insufficien t energy
available to start the eng ine.
Intelligent energy management in your vehi­
cl e ha ndles the dist rib ution o f electr ica l ene r­
gy. Start ing abili ty is m arkedly improved and
the life of the battery is extended .
Bas ica lly, energy management consists of
batt ery diagnosis , idling current manage­
ment
and dynamic energy management .
Battery diagnosis
Battery diagnosis continuously determines
the state of the batte ry. Sensors determine
batte ry voltage, battery cu rr e nt and battery
tempe ratu re. This de termines the cur ren t
state o f cha rge and t he power o f th e battery.
Idling current management
Idli ng current management reduces energy
consumpt ion while the vehicle is standing.
With the ig nition sw itched off, it controls the
energy supp ly to the variou s ele ctri ca l compo ­
nen ts. Da ta from ba ttery d iagnos is is co nsid­
ered.
Depend ing on the batte ry's state of cha rge,
i ndivid ual con sume rs a re g radually turned off
to prevent excessive discharge o f the battery
and th us main tain starting capabi lity.
Dynamic energy management
While the vehicle is being d riven, dynamic en­
ergy ma nagement distr ib utes the energy ge n­
era ted a ccord ing to t he needs of the individ u-
al components.
It r egula tes consumption, so
t h at more e lectrical energy is not being used ..,.

than is being generated and ensures an opti­mal state of charge for the battery.
@ Tips
- But even energy management cannot
negate the limits o f physics. Consider
that the power and life of a battery are
li mited.
- If starting ab ility is threatened, the indi­
cator light
(•i appears ~ page 16, 0
Battery.
What you should know
The highest priority is given to maintaining
starting capability.
The battery is severely taxed in short-dis tance
d riving, in city traffic and during the co ld time
of year . Abundant e lectrica l energy is re­
q ui red, but only a litt le is generated. It is also
cr itical if the engine is not runn ing and electri­
cal components are turned on. In th is in­
stance energy is being consumed but none is
be ing generated .
It is in precisely these situations that you w ill
notice energy management actively regulat­
i ng the distribution of energy.
Vehicle sta nds for an ext ended p eriod
If you do not drive you r vehicle over a period
of several days or weeks, electrical compo­ nents are grad ually cut back or switched
off .
This reduces energy consumption and main­
tains sta rting capab ility over a longer per iod.
Some of the conven ience f unctions may not
ope rate, such as the inter ior lig hts or the
power sea t adjustment. The conven ien ce
f u nctions w ill be ava ilable again when you
switch on the ignit ion and start the engine .
With the engine turned off
If you listen to the radio, for example, with
the engine turned
off or use other MMI func­
tions, the battery is being discharged .
If starting capability is jeopa rdized due to en­
ergy consumpt ion, the fo ll ow ing warning ap­
pears in the MMI display :
Intellig ent technolog y 193
Plea se start the engine soon or the sy stem
will be turned off .
The wa rni ng ind ic ates that the system wi ll be
tu rned
off automatically a fter 3 minu tes. If
you w ish to continue using the funct ions, yo u
have to start the engine.
With the engine running
Althoug h elec trical energy is generated when
t h e ve hicl e is being driven, t he battery can be­
come d ischarged. This happe ns mostly when
little energy is being generated and a great
deal consumed and the battery's state of
charge is not opt imal.
T o b ring the energy ba lance back in to equili ­
brium, consumers which require especially
l a rge amounts of energy a re temporari ly cut
back or sw itched
off. Heat ing systems in par­
ticular require a great deal of energy. If you notice, for example, that the heated seats* or
the heated rear window are not heating, they
have been temporarily cut back or switched
off . These systems w ill be available again as
soon as the ene rgy balance has been restored.
You w ill also notice that engine id le speed has
been increased slightly . Thi s is normal and not
a cause for concern. By inc reasing engi ne id le
speed the additional e nergy requi red is gene r­
ated and the b attery is charged.
•
•

Checking and filling Engine hood
Releasing the engine hood
The engine hood is released from inside the
vehicle .
Fig. 172 Dr iver footwell: release lever
AUD I
Fig. 173 Rocker switch under the hood
Make sure the wiper arms are not raised up
from the w indshield. Otherw ise the paint
could be damaged.
.. Pull the lever under the instrument panel in
the d irect ion of the arrow
<=> fig. 172.
.. Raise the hood slightly<=> _&.
.. Press the rocke r switc h under the hood up­
ward
<=> fig. 173. This re leases the catch .
.. Open the hood .
A WARNING
Hot engine coo lant can burn you.
- To reduce the r isk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine
compartment . Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood.
Checkin g and fillin g 219
Working in the engine compartment
Be especially careful whenever you work in
the engine compartment.
Wh ene ve r y ou must perform an y wo rk in the
eng ine com pa rtm ent , for e xample checking
a nd filling diff ere nt fluids, th ere is a risk of
inju ry, burn s and accid ent s. To pr event per­
so nal injury alwa ys observe the foll owing
WARNING S. The engin e compartment of an y
v e hicle i s a h az a rdou s are a
<=> ,&.
_&. WARNING
To help avoid injury, be fore yo u check any ­
thing under the hood:
- Turn off the engine .
- Sw itch off the ignition.
- Apply the parki ng brake.
- Move selector leve r to "P" (Park).
- Always let the engine cool down. Hot
components w ill burn skin on contact .
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coo la nt escaping from the engine
compa rtment. Wait unt il no steam or
coolant can be seen o r heard before care­
fu lly opening the hood.
- Keep ch ildren away from the engine com­
pa rtment.
- Never sp ill fluids on hot engine compo­
nents . They can cause a fire .
- Never touch the rad iator fan. The auxili­
ary electric fan is temperat ure controlled
a nd can sw itch on suddenly .
- Never open the coolant reservoir cap
when the engine is still warm. The cool­
a nt system is p ressu rized and hot cool­
a nt cou ld spray o ut.
- Protect your face, hands and arm from
steam or hot engine coolant by plac ing a
thick rag ove r the cap when you open the
coo lant rese rvoir.
- If work on the fue l system o r the elec tri­
cal system is necessary:
- Always disconnect the battery.

220 Check ing and filling
- Never smoke or work near heaters or
open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and persona l in­
jury while the engine is running or being
started, never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repa ir
with the engine running:
- First, fully apply the parking brake,
move selector lever to "P" (Park) .
- Always use extreme caution to prevent
clot hing, jewe lry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts. Tie back hair before
start ing, and do not wear cloth ing that
will hang or d roop into the eng ine.
- Min imize exposure to emission and
chem ica l hazards c:> &. .
A WARNING
California Propos ition 65 Warning:
- Engine exhaust, some of its constituents,
and certa in veh icle compone nts co nta in
o r emit chemicals known to the State of
Californ ia to cause cancer and b irth de­
fects a nd rep roduct ive ha rm. In addition,
c ertain f luids con ta ine d in vehicles and
c ertain pro ducts of component wear co n­
tain or emi t chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
- Battery posts, terminals and re lated ac ­
cessories contain lead and lead com- pounds, chemica
ls known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When adding f luids, always make su re that
they are poured into the proper conta iner
or f iller opening, otherwise serious dam­
age to vehicle systems w ill occur.
® For the sake of the environment
To detect lea ks in time, inspect the vehicle
floor pan from underneath regularly. If
you see spots from oil or other veh icle flu­
i ds, have you r vehicle inspected by a n au­
thorized Audi dealer.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced.
.. Let the hood
drop down an d latc h in place.
Do not try to push it shut; it may fail to en­
gage 9 /]}. .
A WARNING ,_ -
A hood that is not completely latched
could fly up and b lock your view while dr iv­
i ng.
- When you close the engine hood, check it to make sure the safety catch has proper­ly engaged. The hood shou ld be flush
wit h the surrou nding vehicle body pa rts .
- If you notice while driv ing that the hood
is not secured properly, stop at once and
close it.