light AUDI A8 2013 Owners Manual

the level may be slightly above the "max"
marking .
The location of the coolant expansion tank
can be seen in the engine compartment illus­
tration ¢
page 234.
To obtain an accurate reading, the engine
must be switched
off.
The expansion tank in your vehicle is equipped
with an electric coolant level sensor.
When the coolant level is too low, the warning
light in the Auto-Check System
¢page 16will
illuminate until you add coolant and the level
has been restored to normal. Even though
there is an electric coolant level sensor , we
still recommend you check the coolant level
from time to time.
Coolant loss
Coolant loss may indicate a leak in the cooling
system. In the event of coolant loss, the cool­
ing system should be inspected immediately
by your authorized Audi dealer.
It is not
enough merely to add coolant.
In a
sealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheating.
& WARNING
The cooling system is under pressure and
can get very hot. Reduce the risk of scald­
ing from hot coolant by following these
steps.
- Turn
off the engine and allow it to cool
down.
- Protect your face, hands and arms from
escaping fluid and steam by covering the
cap with a large, thick rag.
- Turn the cap slowly and very carefully in
a counter-clockwise direction while ap­
plying light, downward pressure on the
top of the cap.
- To avoid being burned, do not spill anti­ freeze or coolant on the exhaust system or hot engine parts . Under certain condi­
tions, the ethylene glycol in engine cool ­
ant can catch fire .
Checking and filling 241
@ Note
Do not add any type of radiator leak seal­
ant to your vehicle's engine coolant. Add­
ing radiator repair fluid may adversely af­
fect the function and performance of your
cooling system and could result in damage not covered by your New Vehicle limited
Warranty .
Adding coolant
Be very careful when adding engine coolant.
Before you check anything in the engine com ­
partment,
always read and heed all WARN­
INGS ¢ & in Working in the engine compart ­
ment on page 232 .
.,. Turn off the engine .
.,. let the engine cool down.
.,. Place a thick rag over the coolant expansion
tank ¢
page 240, fig . 200 and carefully
twist the cap counter-clockwise ¢&_ .
.,. Add coolant.
.,. Twist the cap on again
tightly.
Replacement engine coolant must conform to
exact specifications ¢
page 240, Coolant. We
recommend using only coolant additive G12+
+, G3 or in an emergency G12+. Do
not use a
different additive. In an emergency use plain
water until you can get the correct additive
and can restore the correct ratio. This should
be done as soon as possible.
If you have lost a considerable amount of
coolant , then you should add cold antifreeze
and cold water only when the engine is cold.
Always use
new engine coolant when refilling.
Do not fill coolant above the "MAX" mark. Ex­
cess coolant will be forced out through the pressure relief valve in the cap when the en­
gine becomes hot.
A WARNING
- The cooling system is under pressure and
can get very hot. Reduce the risk of
II-
•
•

24 2 Ch ecking and filling
scalding from hot coolant by following
these steps .
- Turn off the eng ine and a llow it to cool
down.
- Protect your face, hands and arms from escaping flu id and steam by cover ing
the cap with a large, thick rag .
- Turn the cap slowly and very carefully
i n a counter-clockwise direction while
apply ing l ight, downwa rd press ure on
the top of the cap .
- To avo id being burned, do not spi ll an­
tifreeze or coolant on the exhaust sys­
tem or hot engine parts . Under certain
conditions, the ethylene glyco l in en­
gine coolant can catch f ire .
- Antifreeze is poisonous . Always store an­
tifreeze in its or iginal container and we ll
out of the reach of children.
- If you drain the coolant, it must be
caught and safely stored in a proper con­
tainer clear ly marked "poison".
@ Note
- Coolant po llutes the env ironment and
could cause an engine fire . Excess coo l­
ant will be forced out through the pres­
sure re lief valve in the cap when the en­
gine becomes hot.
- If, in an emergency, only water can be
added, the correct ratio between water
and antifreeze
c::> page 240 must be re­
stored as soon as possible .
@ For the sake of the environment
Drained coolant should not be re used. Al­
ways dispose of used coolant while observ­
ing all environmental regulat ions .
Radiator fan
The radiator fan switches on automatically by
itself
T he radiator fan is driven by the engine via the
V-be lt . The viscous clutch regulates the speed
of the fan accord ing to the temperature of the
coolant. An a
uxiliary electric radiator fan* switches on
and off depend ing on coolant temperature
and other vehicle operat ing condit ions .
After yo u sw itch the engine off, the aux iliary
f an can continue running for up to 10 minutes
- eve n wit h the ignit ion off. It can even switc h
on again later by itself
c::> &. , if
- t he tempe rature of the engine coo lant rises
due to the heat build -up from the engine in
the engine compartment, or
- the engine compa rtment heats up because
the vehicle is parked in i ntense sunlight.
_& WARNING
- To reduce the risk of personal injury nev­
er touch the radiator fan.
- The auxiliary electric fan is temperat ure
controlled and can sw itch on suddenly
even when the engine is not running.
- The a uxiliary radiator fan sw itches on au­
tomatically when the engine coo lant
reaches a certai n temperature and will
continue to run until the coolant temper­
ature drops .
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
F ig . 201 E ngin e compart men t: cover on the brake fluid
r eservo ir
Before you check a nyth ing in the engine com­
partment,
always read and hee d all WARN ­
INGS c::> .&. in Working in the engine compart-
ment on page 232. .,..

~ Read the brake fluid level from the brake
fluid reservoir ¢
fig. 201, ¢ page 234. The
brake f luid leve l must be between the "MIN"
and "MAX" markings.
The location of the brake fl uid reservoir can be
seen in the engine compartment illustration
¢page 234.
The fluid level may drop slightly after some
time due to the automatic adjustment of the brake pads . This is not cause for alarm .
If the brake fluid level falls considerably be­
l ow the " MIN" mark, the bra ke wa rning/indi ­
cator light
1111 (U .S . models)/ . (Canadian
models) will come on
¢ page 14. Do not con­
tinue to operate the vehicle. The comp lete
brake system shou ld be thoroughly checked
by an authorized Audi dealer or other quali­
f ied fac ility and the cause corrected. If the
b rake fluid level is too low, the brake warn ing/
i ndicator light w ill illuminate . Co ntact an au­
thor ized Audi dealer
immediately .
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid abso rbs moistu re from the a ir . If
the water content in the brake fluid is too
h igh, cor ros ion in the b rake system may result
after a per iod of t ime . The bo iling po int of t he
b ra ke fluid w ill also decrease considerab ly and
decrease braking performance.
Therefore, the brake flu id must be changed
e very two year s. Always use new b rake fluid
which confo rms to Fede ral Motor Vehicle
Standard "FMVSS 1 16 DOT 4".
The brake flu id rese rvoi r ca n be difficult to
r eac h, therefo re , we re commend that yo u
h ave the brake fl uid changed by you r autho r­
i zed
Audi dealer . Your deale r has the correct
too ls, the right brake fluid and the know-how
to do this fo r you .
Checkin g and fillin g 243
A WARNING
-Brake flu id is poisonous. It must be stor­
ed only in the closed original co ntainer
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
prop riate brake f lu id . Observe these pre ­
cau tions:
- Use only brake fluid tha t meets SA E
s p ecification
J 1703 an d conforms to
Federa l Moto r Ve hicle Standard 116.
Always check with your authorized Audi
dealer to make sure yo u are using the
correct brake fluid. The cor rect type of
brake f lu id is also ind icated on the
brake flu id rese rvoir .
- The brake fluid must be new . Heavy use
of the brakes ca n cause a vapo r lock if
the b ra ke fluid is left i n the system too
l ong. This can se riou sly affect the effi ­
c ien cy of the brakes as well as your
safe ty. This co uld resu lt in an accident.
(D Note
Bra ke fluid will damage the paint of you r
vehicle.
@ For the sake of the environment
Because of t he p rob lem of prope r disposal
of b ra ke fluid as well as the spec ial too ls
r equired and the necessary exper tise, we
r e comme nd th at yo u have the brake fl u id
changed by yo ur autho rized Aud i dea le r.
Battery
General information
U nder normal operating cond itions, the bat­
te ry in your Audi does not need any ma inte­
nance . With
high outside tempe rat ures o r
l ong da ily drives we re commend t hat yo u h ave
the e lec trolyte leve l chec ked by a serv ice f a­
ci lity. The electrolyte leve l should also be
c h ecked each t ime the battery is charged
¢ page 246. IJ,,
•
•

244 Checking and filling
Have the battery checked when you take your
vehicle in for service. You are well advised to replace a battery that is older than 5 years .
W ith certa in types o f airbag deployment, the
battery is disconnected from the vehicle elec ­
trica l system for safety reasons¢
& in Re­
pair, core and disposal of the airbags on
page 166.
Disconnecting the battery terminals
Some veh icle functions (power window regu­
lators, for example) are lost if the battery ter­
minals are disconnected. These functions have
to be re learned after the battery terminals are
connected again. To prevent this, the battery
should only be disconnected from the vehicle
electrical system when absolutely necessary
for repairs .
Vehicles not driven for long period s
If you do not drive your vehicle over a period
of several days or weeks, electrical compo­
nents are gradually cut back or switched off.
This reduces energy consumption and main ­
tains starting capability over a longer period
¢
page 203. Some of the convenience func­
tions may not operate, such as the inte rior
lights or the power seat adjustment . Th e con­
venience functions will be available again
when you switch on the ignition and start the
engine.
Winter operation
During the winter months, battery capacity
tends to decrease as tempe rat ures drop . This
is because more powe r is also consumed while
starting , and the headlights, rear window de ­
fogger, etc., are used more often.
Avoid unnecessary power consumption, par­
ticular ly in city traffic or when traveling on ly
short distances. Let your authorized Audi
dealer check the capacity of the vehicle bat ­
tery before winter sets in
¢ page 246. A well
charged battery w ill not only prevent starting
prob lems when the weather is cold, but will
also last longer .
(D Tips
If your vehicle is left standing for seve ral
weeks at extremely low temperatures, the
vehicle battery sho uld be removed and
stored where it w ill not freeze . This will
prevent it from being damaged and having
to be replaced .
Working on the battery
Be especially careful when working on or near
the battery.
The battery is located in the luggage compart­
ment under the floor. Before you check any­
th ing in the luggage compartment,
read and
heed all WARNINGS
¢ ,& .
Always heed the safety warnings, when work­
ing on the vehicle battery or the vehicle elec­
trical system to prevent injury.
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM­BOLS and safety precautions when working
on the battery.
®
Always wear eye protection.
Battery acid contains sulfuric acid.
Always wear gloves and eye protec­
tion.
No
- sparks
- flames
- smoking.
When a battery is charged, it produ­
ces hydrogen gas which is explosive
and could cause personal injury.
Always keep the battery well out of
I
reach of children .
_&. WARNING ~
Whenever working on the battery or on
the electrical system, there is the risk of
injury, accident and even fire . Read and
heed the following WARNINGS:
-

-Always wear eye protection. Do not let
battery acid or any lead particles get on
your skin or clothing. Shield your eyes .
Explosive gases can cause blindness or
other injury.
- Battery acid contains sulfuric acid . Sulfu­
ric acid can cause blindness and severe
burns.
- Always wear gloves and eye protection.
Do not tilt the battery because acid
could leak out of the ventilation open­
ings.
- If you get battery acid in your eyes or
on your skin, immediately rinse with
cold water for several minutes and get
medical attention .
- If you should ingest any battery acid,
seek medical attention immediately.
- Do not expose the battery to an open
flame, electric sparks or an open light.
- Do not smoke.
- Do not interchange the positive and neg-
ative cables .
= When working on the battery, be sure
not to short-circuit the terminals with
tools or other metal objects. This would cause the battery to heat up very quickly,
which could lead to damage or explosion and personal injury.
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury .
- Always keep the battery well out of the
reach of children.
- Before work is done on the electrical sys­
tem, disconnect the negative ground ca­ ble .
- Before performing any work on the elec­
trical system, switch off the engine and
ignition as well as any electrical equip ­
ment. The negative cable on the battery
must be disconnected . If you are just go­
ing to replace a light bulb, then it is
enough to switch off the lights.
- Before disconnecting the battery, switch
off the anti-theft alarm system! Other­
wise you will set off the alarm.
Checking and filling 245
-When disconnecting the battery, first
disconnect the negative cable and then
the positive cable.
- Before reconnecting the battery, make
sure all electrical consumers are switch­
ed off. Reconnect the positive cable first
and then the negative cable . Never inter ­
change the cables -this could start a fire!
- Never charge a frozen or a thawed-out
battery . It could explode! If a battery has
frozen , then it must be replaced . A dis­
charged battery can freeze over at 32 °F
(0 °C) .
-Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery .
- Never use batteries which are damaged.
There is the danger of an explosion! Al­
ways replace a damaged battery.
&_ WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems. Wash hands after han­ dling.
(D Note
- Do not disconnect the vehicle battery
when the ignition is on or when the en­ gine is running, otherwise, you will dam­
age electronic components in the electri­
cal system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect the battery from "freezing", oth­
erwise it will be damaged and will then
have to be replaced.
•
•

CD Note
Never use a fast charger as a booster to
start the engine . This will seriously dam­
age sensitive electronic components, such
as control units, relays, radio, etc ., as well
as the battery charger .
Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery .
Intelligent energy management in your vehi­
cle is responsible for d istributing the electr i­
cal energy throughout your vehicle
c::> page 203 . The intelligent energy manage­
ment system w ill keep the engine battery
charged bette r than vehicles w ithout t his sys­
tem. To make sure the additional electr ica l en­
ergy is available once again after you have
changed the battery, we recommend that you
install batteries of the same type and manu­
facture only (the same as those installed at
the time your vehicle was delivered). Specifi­
cations are listed on the bat tery hous ing. Your
author ized dealer must code the battery in
the energy management system to enable you
to use the energy management functions cor­
rectly after replac ing the battery .
T he new battery must have the same capacity ,
voltage (12 volts), amperage, construction and p lug sealing.
When installing the battery, make sure the ig­
n ition and all electr ical consumers are sw itch­
ed off .
CD Note
-Make sure the ventilat ion hose on the
s ide of the battery is connected, other­
wise fumes or battery acid can leak out.
- Vehicles with the Start-Stop-System* are
equipped with a special cycle-proof AGM
battery. Insta lling a different type of
batte ry can cause prob lems in the vehi­
cle elect rical system. When replacing the
vehicle battery, always insta ll one wi th
Checkin g and fillin g 247
the same specifications as the origina l
battery .
- Battery mounts and clamps must always
be sec ured correct ly .
- Read and fo ll ow the warnings under
c::> page 244, Working on the battery be ­
fore performing any work on the battery.
@ For the sake of the environment
Because of the prob lem of p roper disposal
of a ba ttery, we recommend your author­
ized Audi dealer change the battery for
you. Batteries contain sulfuric acid and l ead and must always be disposed of prop­
erly in compliance with all environmental
regulat ions. Disposing of vehicle batter ies
i mproperly is very dangerous to the envi­
r o nment .
Windshield/headlight
washer container
.., N
-N
" ~
Fig. 203 Eng in e compa rtm ent: cove r on the w inds hield
washer flu id rese rvo ir
T he washer fluid container is marked w ith the
symbol-$ on its cap
c::>fig. 203, c::>page 234.
.,. Before you check anything in the engine
compa rtment, always read and heed all
WARNINGS c::> A in Working in the engine
compartment on page 232.
.,. Lift the filler cap tongue to add washer flu­
id. You can fi ll the container to the top .
.,. Press the cap back onto the f iller neck after
filling the container .
You can find the reservoir capacity in the table
inc::>page292. ""
•
•

254 Tires and wheels
Bear in mind that the tire pressure monitoring
system* can only monitor the tire pressures
you have stored . The system does not recog­
nize the load condit ion of your vehicle.
The effectiveness of the tire pressure monitor ­
ing system* will be impaired if you store nor­
mal load pressures but then operate the vehi ­
cle at its max imum load
c:> &. .
See the illustration c:> fig. 204 for the location
of the label on driver's side B-pillar (color of
the act ua l label and exact location on the ve­
hicle will vary slightly). Note
that the following table is accurate at
the time of going to press and is subject to
change. In the event of d iscrepancies, the t ire
pressure label is located on the driver's side B­
pillar always takes precedence.
The table below lists the recommended cold
t ir e inflation pressures for the Audi mode l
covered by your Owner's Literature at the vehi­
cle's capacity weight and the t ire sizes instal­
led on the respective models as orig inal
equipment, or as a factory opt ion.
Tire pressure
Model/En­ gine Tire designation
normal load condition full load condition
AB/AB L: 235/55 R18 104H
3.0
liter 255/45 R19 104H
6
-cyli nd
er 265/40 R20 104H
265/40 R20 104V
275/35 R21103Y XL
AS/AS L: 235/55 R18 104H
4.0
liter 255/45 R19 104H
B-cyli nd
er 265/40 R20 104H
265/40 R20 104V
275/35 R21103Y XL
AS/AB L: 235/55 R18 104H
4.2
liter 255/45 R19 104H
B-cyli nd
er 265/40 R20 104V
ASL:
6.3 liter
12-cylin­
der
265/40 R20 104H
275/35 R21103Y XL
265/40 R20 104V
255/45 R19 104H
265/40 R20 104H
275/35 R21103Y XL
SB: 265/40 R20 104V
4.0
liter 265/35 R21101 Y
B-cyli nd
er 275/35 R21103Y XL
rearal front rear
PSI kPA PSI kPA PSI kPA PSI kPA
260
260
260
240
240
260
260
260
240
260
260
260
240
260
260
240
260
260
240
XL= reinforced or extra load tire. It may also appear as xl, EXTRA LOAD, or RF on the tire side­
wall.
•> normal load condition <=>page 253 .

256 Tires and wheels
the time it was manufactured . For the
location of the label~
page 253, fig . 204.
Most tires lose air naturally over time. They
can also lose some air if you drive ove r a pot­
hole or hit a curb while parking . It is usually
not possible to see whether the radial tires
used today are under inflated just by looking
at them.
Therefore, be sure to check tire pressures at
least once a month and always before going
on a long tr ip. Make sure to take the number
of people and the amount of luggage into ac­
count when adjusting tire pressure for a trip -
even one that you would not consider to be
"long." See~
page 257, Tires and vehicle
load limits
for more important information.
Always use an accurate tire pressure gauge
when checking and adjusting inflation pres­
sures. Check all of the tires and be sure not to
forget the spare t ire. If the pressure in any tire
is too high when the tire is "cold," let air out
of the tire slowly with the edge of the tire
gauge and keep checking the pressure until
you reach the pressure that is correct for the
l oad (passengers and luggage) and kind of
driving you plan to do.
If the pressure in any tire is too low, note the
difference between the pressure in the cold
tire and the pressure you need and add the air
that you need to reach the correct pressure for
the vehicle load (passengers and luggage) for
the tires on your vehicle as listed on the on
your veh icle and in this manual and the kind
of dr iving you plan to do .
Never exceed the maximum inflation pres­
sure listed on the tire sidewall for any rea­
son.
Remember that the vehicle manufacturer, not
the tire manufacturer, determ ines the correct
tire pressure for the tires on your vehicle.
It is important to check the tire pressure when
the tires are cold.
- Read the req uired ti re pressure from the tire
pressure label. The tire pressure label is lo ­
cated on the driver's side B-pi llar . -
Tu rn the va lve stem cap counter -clockwise
to remove it from the tire va lve .
- Place the air pressure gauge on the va lve.
- The tire pressu res should only be checked
and adjusted when the tires are cold. The
slightly raised pressures of warm tires must
not be reduced.
- Adjust the tire pressure to the load you are
carrying.
- Reins tall the valve stem cap on the valve.
When should I check the tire pressure?
The correct tire pressure is especially impor­
tant at high speeds. The pressure should
therefore be checked at least once a month
and always before starting a jour ney. Do not
f orget to check the tire pressure for the spare
whee l
~page 272.
When should I adjust the tire pressures?
Adjust the tire pressure to the load you are
carrying. After changing a wheel
or replacing
whee ls you have to adjust the tire pressures
on all whee ls. In addition, you m ust then
store the new tire pressures in the tire pres­
sure monitoring system*~
page 267.
A WARNING
Incorrect tire pressures and/or underinfla­
tion can lead sudden tire fa ilure, loss of
control, collision, serious personal injury
or even death.
- When the warning symbol
Rt] appears in
the instrument cluster, stop and inspect
the tires.
- Incorrect tire pressure and/or underinfla­
tion can cause increased tire wear and
can affect the handling of the vehicle and
stopping abi lity.
- Incorrect tire pressures and/or underin­
flation can also lead to su dden t ire fail­
ure, including a blowout and sudden de­
flation, causing loss of veh icle control.
- The driver is responsible for the correct
tire pressures for all tires on the vehicle.
The applicable pressure values are locat­ ed on a sticker on the driver's side B-pil-
la~
~

268 Tires and wheels
and may affect the vehicle's handling and
stopping ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv­
er's responsibility to maintain correct tire
pressure, even if under-inflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale .
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the sys­
tem detects a malfunction, the telltale will
flash for approximately one minute and then
remain continuously illuminated. This se­
quence will continue upon subsequent vehicle
start-ups as long as the malfunction ex ists.
When the malfunct ion indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended . TPMS
malfunctions may occur for a variety of rea­
sons, including the installation of replace­
ment or a lternate tires or whee ls on the vehi­
cle that prevent the TPMS from functioning
properly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the re­ placement or alternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
App lies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction .
Fig. 209 Display: underinflation warning
Fig. 210 Disp lay: System malfunction
Using the ABS sensors, the tire pressure moni ­
toring system compares the tire tread cir cum­
ference and vibration character istics of the in ­
dividua l tires. If the pressure decreases in one
o r more t ires, this is ind icated in the instru­
ment cluster with a warning symbol
[«E and a
message ~
fig. 209.
The tire pressure monitoring system must be
reset via MMI each t ime the press ures are ad­
justed (e.g. when switching between partial
and full load pressure) or after changing or re­
placing a tire on your vehicle
c::> page 269. The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on driver's side 8-pillar
c::> page 2 53.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low,
- the tire has structural damage ,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
c::> page269.
Warning symbols
[tE Loss of pressure in at least one tire c::> ,1,. .
Check the tire or tires and replace or repair if
necessary. The indicator light
[tE in the instru­
ment cluster also illuminates
c::> page 11.
Check/correct the pressures of all four tires
and reset TPMS via MMI.
119;~, < T ire Pressure Monitoring System) Tire
pressure! System malfunction .
IJJ,-

If llil~, appears after switching the ignition
on or whi le driving
¢ fig. 210 and the indica­
tor light
ltJ in the instrument cluster blinks
for approximate ly one minute and then stays
on, there is a system malfunction .
Attempt to store the correct tire pressure
¢
page 269. If the indicator light does not
turn off or if it turns on short ly thereafter, im­
mediately drive your vehicle to an authorized
Audi dealer or authorized repair facility to have the malfunction corrected .
A WARNING
-If the t ire pressure indicator appears in
the instrument cluster d isplay, one or
more of you r tires is s ignificantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possible and
check the t ires and the ir pressures. In­
flate the tire pressure to the proper pres­
sure as indicated on the vehicle's tire pressure label ¢
page 253. Driving on a
significantly under -inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle 's handling and stop­
ping ability.
- T he driver is responsible for ma inta ining
the corre ct tire pressures. You m ust
check the t ire pressures regularly .
- Under certain cond itions (such as a spor­
ty driving style, w inter condit ions or un­
paved roads) , the pressure monitor indi­
cator may be de layed .
- Ask your author ized Audi dealer if run ­
flat tires may be used on your vehicle.
Your vehicle regist rat ion becomes invalid
if you use these tires when not permit­
ted. Damage to your veh icle or acc idents
cou ld also resu lt.
(D Tips
- The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
Tire s an d wheel s 269
- Us ing snow chains may res ult in a system
ma lfunction.
- T he tire pressure mon itor ing system on
your Audi was deve loped using tires with
the "AO" or "RO" identification on the
t ire s idewall
c:> page 260. We recom­
mend us ing these tires.
Reset tire pressure monitoring system
App lies to vehicles: wit h tire press ure mo nitor ing system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
MMI.
.,. Switch on the ignition.
.,. Select in the MMI: ICAR lfunction button>
Ca r sy stems control button > Servicing &
checks > Tire pressure monitor ing > Store
t ire pr essur es> Yes, store now .
(D Tips
Do not store the tire pressure if there are
snow cha ins on the tire .
•
•