oil AUDI A8 2014 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2014, Model line: A8, Model: AUDI A8 2014Pages: 314, PDF Size: 78.47 MB
Page 13 of 314
Instrument s and warnin g/indic ator ligh ts 11
gauge turn on under normal d riving condi
tions . The LEDs higher up may turn on when
the eng ine is under heavy load or the exter ior
temperature is high . This is no need to worry
as long as the. warning light in the instru
ment cluster does not illuminate . If the LEDs
in the upper area of the display and the ind ica
tor light . in the instrument cluster d isplay
turn on, the coolant temperature is too high
¢ page 16.
A WARNING
-Always observe the warning in
~ page 231, Working in the engine
compartment,
before opening the hood
and checking the engine coolant level.
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment.
You could burn yourself. Let the engine
cool off first so that you cannot hear or
see any steam or engine coolant .
(D Note
- Mounting additional lights or accessories
in front of the a ir inlets reduces the cool
i ng effect of the rad iator . At h igh outside
temperatures or high eng ine load, the
engine co uld overheat.
- The front spo ile r has been designed to
properly distrib ute the cooling air when
the veh icle is moving. If the spoiler is
damaged, this cou ld red uce the cooling
effect and t he engine co uld then over
heat . Ask your aut ho rized Audi dea le r for
ass istance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM
(revolutions per minutes).
If engine R PM drops be low 1,500, you should
downshift to the next lower gear. The red a rea
at the end of the sca le ind icates maxim um
perm iss ible engine RPM after the break-in pe
riod. Before reaching this area, move these
lector lever to position "D (Drive)" or ease
your foot off the accelerator pedal.
@ Note
The tachometer need le should only briefly
be in the red zone: yo u could damage your
engine! The beg inning of the red zone var
i es dependi ng on the engine.
@ For the sake of the environment
Upsh ifting early saves fuel and reduces en
gine noise.
Fuel gauge
The fuel gauge only works when the ignition is
o n.
If the fue l level drops below 4 gallons (15
l ite rs), the bottom LE D tu rns red and the indi
cator light~ turns on
c::> page 21. The bot
tom LED b link s red when the fue l level is very
l ow .
The possible range based on the current fuel
level is shown in tab@~
page 24, fig. 4.
(D Note
Never run the ta nk complet ely dry. An ir
regular supply of f uel can cause engine
misfiring and fuel cou ld enter the exha ust
system. The cata lytic converter could t hen
overheat and be damaged .
Warning/indicator
lights
Description
T he ind icator lights in the ins trument clus ter
blink or turn on. They indica te fu nct ions or
malfunctions
c;;> ,& .
Messages may appea r with some indicato r
li ghts. A warning signal will sound at the
same t ime. The indica tor lights an d messages
in the center of the displays may be rep laced
by other disp lays. To show them again, select
the tab for ind icator lights and messages us
ing the multifunction steering whee l
c;;> page 24. If there are several malfunc
tions, you can display them one at a time us- ing the thumbwheel. ..,.
Page 15 of 314
Instruments and warning/indicator lights 13
Refill Ad Blue*
1:11
Malfunction indicator Lamp
c::;, page 227 (MIL) ../
AdBlue malfunction*
¢page 20
c::;,page227
•
Diesel particu late filter* clogged
Yellow indicator lights
c::;, page 21 .
Yellow symbols indicate a priority 2 ma lfunc-
111
Engine speed limitation
c::;, page 21 tion -Warning!
Engine oil level
I
USA models: Safety systems
•
c::;, page 18 c::;,
page 17 •
El
Canada models: Safety systems
•
Eng ine oil sensor
c::;, page 18 c::;,
page 21
Electronic Stabilization Control
&1
Battery
II
(ESC) ../ c::;, page 16
c::;, page 18
Em
Tank system
I
Electronic Stabilization Control c::;, page 21
(ESC) ../
c::;,page 18
•
Windshield washer fluid level
USA models: c::;, page 21
~
Anti-lock braking system (ABS)
m
W indshield wipers
defective
c::;, page 2 2
¢page 19
Canada models:
!I
Remote control key
ti]
Anti-lock braking system (ABS) c::;,page84
defective
=
Remote control key
¢page 19
c::;, page 84
•
Worn brake pads
Battery in remote control key
c::;, page 20
!! c::;, page 32
•
Electromechanical parking brake
Defective light bulb warning
c::;,page 86
l:J c::;, page 2 2
[I]
Tir e p ressure monitoring system
Fog lights*
,/
II c::;, page 2 66 c::;, page 2 2
mm
Tir e p ressure monitoring system
II
Rear fog lights*
¢page 266 c::;, page 2 2
rm
Electronic power control (alter-
II
Headlight range control
native
to g c::;, page 2 2
c::;, page 20
•
Glow plug system
§l
adaptive light*
(alternat ive to
'3B >
c::;, page 2 2
c::;, page 20
m
Light-/rain sensor faulty
c::;, page 2 2
Page 19 of 314
Instruments and warning/indicator lights 17
Seek professional assistance if the battery
charge leve l is too low.
(•) Low battery charge: battery will be
c harged while driving
If the indicator light turns on and the mes
sage appears, there may be limited start ing
ability.
If th is message turns off after a little wh ile,
the battery charged enough wh ile driving .
If the message does not turn off, have your
author ized Audi dealer or qualified workshop
correct the malfunction.
~ Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair . Driving
with a low-oil-pressure indication is likely to
inflict severe damage to the engine.
• Switch off engine and check oil level
If the indicator light turns on and the mes
sage appears, the oil pressure is too low.
.. Pull off the road.
.. Stop the vehicle .
.. Turn off the engine.
.,. Check the engine oil level¢ page 236 .
.. If the engine oil level is too low, add engine
o il ¢
page 237 . Make sure that the oil pres
sure warning symbol. appears no longer
in the d isplay before you start driving again.
.,. If the engine oil level is correct and the indi
cator light st ill turns on, turn the engine off
and do not continue driving. Seek professio
nal assistance.
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter·
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
Ill requires oil refill or workshop serv
ice without delay. Do not wait until the red oil pressure
warning. starts to
flash before you respond to the low oil
level warning
II. By then, your engine
may already have suffered serious dam
age.
~"' Engine oil level
• WARNING : Please add oil immediately
If the indicator light and the driver message
appear, add engine o il immed iately
¢ page 234.
II Add oil, max . x qt (l). You may continue
driving
When the symbol and the driver message ap
pear, add the amount of oil appearing in the
display at the next opportunity ¢
page 234.
@-Steering column lock
• Do not drive vehicle: Steering defective
If the indicator light turns on and the mes
sage appears, there is an e lectronic steering
column lock malfunction. You cannot switch
the ignit ion on .
Do
not tow your vehicle because it cannot be
steered. Seek professiona l assistance .
!'II Steering lock: system fault. Please con
tact deale r
If the indicator light turns on and the mes
sage appears, there is an e lectronic stee ring
column lock malfunction.
Drive to your authorized Audi dealer immedi
ate ly to have the malfunction corrected .
A WARNING
Your vehicle must not be towed in the
event of a malfunction in the elec tron ic
steering column lock because it cannot be
steered due to the locked steering . If it is
towed with the steering locked, there is
the r isk of an accident.
Page 23 of 314
Instruments and warning/indicator lights 21
switched on and will turn off after the engine
has started and has sett led at a constant idle
speed . This ind icates that the MIL is working
properly .
The warning light illuminates when there is a
malfunction in the engine e lectronic system .
Contact your author ized Audi dealer and have
the malfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢page 225.
For mo re in format ion ¢ page 29.
~. Diesel particulate filter clogged
Appl ies to vehicles: with d iesel e ngine and diese l pa rticu
late fi lte r
II Particulate filter : System fault See own
er's manual
When the Ill symbol illuminates, you can al
ter your driving style to assist the filter self
cleaning process. Drive for approximately 15
minutes with the selector lever in the 5 posi
tion at a minimum speed of 37 mph (60 km/
h) and an engine speed of approximately
2,000 RPM. The temperature increase that
will resu lt from this can burn off the soot in
the filter . The symbol will switch off when the
cleaning is successful. After a successful
cleaning , there is no need to bring the car to
an author ized dealer or qualified workshop
because this is part of normal vehicle ope ra
tion .
If the symbol
&I does not switch off, see
your author ized dealer or other qualified
workshop to have the prob lem corrected.
For more informat ion on the d iesel particu
late filter , refer to¢
page 208.
A WARNING
Always adapt your speed to the current
weather, road and traffic conditions. You
should never disobey traffic laws in order
to follow driving recommendations.
-
!'1 Engine speed limitation
App lies to veh icles: w it h e ngine speed lim itat io n
(II Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed d isplayed in the driver information
system. This protects the engine from over·
heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera
ture range and you have re leased the accelera
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica
tor light
lli also turns on. Make sure that the
speed does not go above the speed disp layed.
Drive to your authorized Audi dealer immedi
ate ly to have the malfunction corrected.
~v, Engine oil sensor
Ill Oil level! Sensor defective
If the symbol illum inates, contact your au
thorized Audi dea le r and have the oil sensor
inspected. Until you have this done, check the
oi l level each time you refue l just to be on the
safe side¢
page 236.
Bu Fuel level indicator
Ii') Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 4 gallons (15 liters) of fuel left in the
tank. Time to refuel
q page 224.
Ii] Tank system malfunction! Contact dealer
If th e indicator light turns on and this mes
sage appears, there is a malfunction in the
tank system.
D rive to your authorized Audi dealer immedi
ate ly to have the malfunction corrected.
Page 25 of 314
Instruments and warning/indicator lights 23
Drive s low ly to your authorized Audi dealer or
qualified workshop to have the malfunction
corrected .
,'I'M Dynamic steering: initializing
If thi s driver message appears and the indica
tor light is flashing on the inst rument panel ,
dynamic steering is being reiniti alized . Once
you sta rt the engine after this is finished, the
steering whee l wi ll be easy to move . Re-initi
alization might be necessary if the steering
wheel was moved hard to the left and r ight
while the veh icle was not moving. The displ ay
goes out as soon as initialization is complete .
A WARNING
-
Have the dynamic steering system mal
function repaired as soon as poss ible by an
authorized Audi dealer or any qualified
workshop - risk of accident!
@ Tips
-The dynamic steering stability systems
are not available in the event of a system
malfunction.
- For additional informat ion on dynamic
steering, refer to
¢page 110.
I-: Sport differential
Ill Sport differential: system fault
There is a malfunct ion with the sport differen
tial.
Drive to your authori zed Aud i dea ler immedi
ately to have the malfunction corrected.
Ill Sport differential: overheating
The transmission temperature has incre ased
sign ificantly due to the sporty driving manner.
Dr ive in a less sporty manner until the tem
pe rat ure returns to the normal range and the
indicator light switches of.
A WARNING
Contact your authorized Audi dealer or a
qualif ied workshop if the sport different ial
is faulty or malfunctioning . The repa ir
-
must be performed by trained personnel
using the correct oil in order to ensure
safety.
¢¢ Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left II or the r ight II
turn signal, the indicator light blinks. When
you use the emergency f lashers, both indica
tor lights flash .
If one of the turn signa l light bulbs burn out,
the turn signal wi ll blink twice as fast as nor
mal. Carefu lly drive to your authorized Audi
dealer immed iate ly to have the malfunction
corrected. The indicator light does not indi
cate a malfunction if a turn signal on the tra il
er or on the vehicle fails in trailer tow ing
mode .
(D Tips
For more information on the turn s ignals,
refer to¢
page 48.
Page 30 of 314
28 Instruments and warning/indicator lights
The date and time are shown in the instru
ment cluster d isplay
c:;, page 24, fig. 4. There
is also an ana log clock in the center console
c:;, fig. 12.
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds . When the ign ition is switched
on, the time is always displayed in the status
line © regardless of the current display.
You can set the time on both clocks and the date display in the MMI. Refer to the MMI
owner's manual for instructions.
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 13 Inst rume nt cluster: Serv ice inte rval d isp lay
The schedule for the next oil change or inspec
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv
ice reminder appears in the display when you
switch the ignition on
c:;, fig. 13 .
After about S seconds the display switches back to normal. The distance and time re
maining are updated each time the ignition is
switched on until the date due for service is
reached .
Service due
When the due date for service is reached, the
message
Service due! appears in the instru
ment cluster immediately after you switch the
ignition on . Additionally, a warn ing tone sounds. After about 5 seconds the disp
lay
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > Car sys
tems
control button > Servicing & checks >
Service interval displays.
Resetting the service interval display
Your authorized Audi dealer will reset the cor
responding service schedule after performing
the appropr iate service on your vehicle. You
also have the possibility to reset the oil
change schedule after hav ing performed an
o il change according to Aud i specif ications.
Select the
I CAR I function button > Car sys
tems
control button > Servicing & checks >
Service Intervals > Reset oil change interval.
(D Note
If you disconnect the battery term inals, no
calculations can be made for the service
i nterval disp lay during th is time and no
serv ice reminder will appear. Remember
that observing the proper service intervals
i s vitally important to extending the life of
your vehicle, pa rticularly the engine, and
maintaining its value. Even if the mileage
driven is low, the maximum period of one
year from one service to the next must not
be exceeded.
(I} Tips
-Do not reset the display between oil
changes, otherwise the disp lay w ill be in
correct.
- The information in the Service Reminder
remains stored
even when the vehicle
battery is disconnected .
Page 86 of 314
84 On the road
the stored position as soon as you switch on
the ignition.
Starting and stopping
the engine
Starting the engine
This button switches on the ignition and
starts the engine.
Fig. 85 Cente r console: START ENGINE S TOP b utton
Sw itching the i gni tion on /off
~ To switch the ignition on/off, press the
I START
ENGINE STOPI button. Do not press
the brake pedal while do ing this . D iesel
vehicles are preheated wh ile the ignition is
switched on.
Starting the engine
~ Press the brake pedal Q &,.
~ Press the I START ENGINE STOPI button
Q fig. 85 . The engine will start.
~ It is possible that there w ill be a slight delay
when start ing the engine for diesel vehicles
i n colder temperatures . T herefore, yo u m ust
hold the brake pedal down until the engine
sta rts . The indicator lamp
& il luminates
when the eng ine is preheated.
I f the engine does not sta rt immedia tely, the
starting process is automatica lly stopped af
ter a short time. Repeat starting proced ure.
Start -Stop -System *:
Note the information on Q page 88, Start
Stop-System.
A WARNING ,-
- Never allow the engine to run in conf ined
spaces -danger of asphyx iat ion.
- Never turn off the engine until the vehi
cle has come to a complete stop.
- The brake booster and power steering
only work when the engine is running. If
the engine is off, you have to use more
force when steering or brak ing. Because
you cannot steer and brake as you usual
ly would, th is cou ld lead to crashes and
ser io us inju ries.
(D Note
- Avo id h igh engine rpm, full throttle and
heavy eng ine loads until the eng ine has
reached operating temperature -other
w ise you risk engine d amage.
- T he engine cannot be started by pushing
o r towing the vehicle.
(1) Tips
- After a co ld e ngine is started, there may
be a brief pe riod of inc reased noise be
cause oil pressure must first build up i n
t he hydraulic valve adjusters. This is nor
ma l and not a cause for conce rn.
- If you leave the veh icle with the ignition
switched on, the ignit ion w ill switch off
afte r a certain period of time. Please
note that electrical eq uipment such as
exterior lights will sw itch off as well
when that happens.
Stopping the engine
~ Bring your vehicle to a complete stop.
~ Move the selector lever to the P or N posi
tion.
~ Pr essthelS TART ENGINE STO Plbutton
Q page 84, fig. 85.
When you stop and the Start-Stop-System*
turns off the engine, the ignition remains on .
Press the I START
ENGINE STOPI button to
swi tch the ignition off d uring a stop phase.
IJII-
Page 205 of 314
Clean off accumulated salt coating from
brake discs and pads with a few careful
brake applicat ions .
-If you damage the front spoiler, or if you
install a different spoiler, be sure the air
flow to the front brakes is not obstruct ed . Otherwise the brake system could
overheat reducing the effectiveness of
the ent ire brake system.
- Failure of one brake c ircuit will impair
the braking capability resulting in an in
cr eased stopp ing distance. Avoid driv ing
the vehicle and have it towed to the near est Aud i dea ler or q ualified wor kshop .
- Never let the vehicle rol l to a stop w ith
t he engine shu t off.
- If the brake booster is not work ing, the
brake pedal must be pressed conside ra
bly harder to make up for the lac k of
booster assistance.
Brake booster
The brake booster adds extra braking power.
The brake booster works w ith vacuum pres
sure which is created only when the engine is
ru nning
9 ,&. .
,&. WARNING
-Never le t the vehicle ro ll to a stop w ith
t he engine shu t off.
- If the brake booster is not work ing, fo r
ex ample when towing your ve hicl e, or
because the b rake booste r has somehow
been damaged, the brake pedal must be
pressed considerab ly harder to make up
for the lack of booster assistance.
Servotronic - advanced
power steering system
-
The power steering systems use the power of
the running engine to allow precise steering
with little effort.
The advanced Servotronic power steering sys
tem senses the road speed and electron ically
ad ju sts powe r ass istance to provide comfor ta-
Int ellig ent technolog y 203
ble and safe steering response exactly match
ed to th e vehicle speed .
Power steer ing will not work if the engine is
off . As a result, the steering wheel will be h ard
to tu rn.
T he powe r stee ring fluid level is checked d ur
i ng t he sched uled maintena nce services.
(D Note
If there is an e lectronic malfunction, ser
votronic
will s till fu nction like a conven
tiona l powe r steering system, providing a
constant steering s upport force tha t is no
l onge r proportionate to the vehicle speed.
This is most noticeab le when t urni ng the
steering wheel at low speeds (for example
when parking), -more effort w ill be re
quired than usual.
- Be aware of the different than usual steering response and adjust your steer
ing force accordingly.
- Have the problem checked and set right by an Audi dealer as soon as possible.
(D Tips
-When the engine is running, never hold
the steering wheel turned all the way to
the right or to the left for longer than 15
seconds . The power steering pump will
overheat the hydraulic fluid if yo u keep
holding the stee ring wheel turned all the
way. This is likely to damage the power
steering sys tem.
- If the powe r stee ring system should fa il
entire ly, o r if t he engine is not runn ing
(for example, wh ile be ing towed), you
w ill still be able to steer the veh icle .
However,
considerably more effort will
be required to do so .
- If the powe r steering system sho uld
have a leak, or is not functioning proper
ly, contact your author ized Audi dealer
immediately.
- The power steering system req uires a
specially formu lated hydraulic fluid. The
power steering fluid reservoir is located
in the engine compartment
9 page 233. IJJ,,
•
•
Page 210 of 314
208 Driving and en vir onm ent
Catalytic converter
Appl ies to vehicles: with gasoline e ngin e
It is very important that your emission con
trol system (catalytic converter) is function
ing properly to ensure that your vehicle is run
ning in an environmentally sound manner .
.. Always use lead-free gasoline i=> page 222,
Fuel supply .
.. Never run the tank down all the way to emp-
ty .
.. Never put too much motor oil in your engine
¢ page 23 7, Adding engine oil
The catalytic converter is an eff ic ient "clean
up" device built into the exhaust system of
the vehicle. The catalyti c converter burns
many of the pollutants in the exhaust gas be
fore they are released into the atmosphere.
The exclus ive use of unleaded fuel is cr itically
important for the l ife of the cata lytic convert
e r and proper functioning of the engine.
A WARNING
T he temperature of the exhaust system is
high, both when driving and after stopping
the engine .
- Never touch the exhaust tail pipes once
they have become hot. This could result
in burns.
- Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can
cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
man ifold, exhaust p ipes, catalytic con
verter or heat shields . During driving, the
substance used for undercoating cou ld
overheat and cause a fire.
@) Note
- Be aware that just one tank f illing with
leaded fuel will already seriously de
grade the performance of the cata lytic
conve rter. -
Do not exceed the correct engine oil level
i=>page 237.
-Do not drive until the fue l tank becomes
completely empty . The engine co uld mis
fire . Unburned fuel could also get into
the exhaust system and this cou ld cause
the catalytic converter to overheat.
- Do not switch off the ignition while the
vehicle is mov ing.
- Do not continue to operate your vehicle
under these conditions, as otherwise fuel
can reach the catalyt ic converter. Th is
cou ld result in overheating of the con
verter, requir ing its replacement .
- To assure efficient operation of the Emis
sion Control System:
- Have you r vehicle maintained p roperly
and in accordance w ith the service rec
ommendations in your Warranty & Maintenance book let.
- Lack of prope r maintenance as we ll as
improper use of the vehicle wi ll impair
the function of the em ission contro l
system and could lead to damage.
@) For the sa ke of the en vironment
Even when the Emission Control System is
ope rat ing properly, the exhaust gas can
have a sulfur-like exhaust gas smell under
some operat ing states. This depends on
the sulfur content of the fuel being used .
Using a different brand of fuel may help,
or f illing the tank with lead-free super
grade gasoline.
Diesel particulate filter
Applies to vehicles: with diese l eng ine
The diesel part icu late filter filters nearly all of
the soot pa rticles out of the exhaust . T he fil
ter cleans itself automat ica lly unde r no rma l
dr iv ing cond itions . If the filte r cannot clean it
self (for example, because you are on ly driving
short distances), the filter becomes clogged
with soot and the
II symbol for the diesel
particulate filter i lluminates
i=> page 21. ..,.
Page 211 of 314
A WARNING ,~
- Do not park your vehicle over flammable
materials such as grass or leaves because
the high temperature of the diesel par
t icu late filter cou ld start a fire .
- Do not apply an underbody protectant in the exhaust system area or a fire could start .
Shutting down vehicle
If you would like your veh icle to remain inop
erat ive for a longer period of time, contact an
Aud i or other specia lized dealer. They can ad
vise you on necessary precautions e.g . corro
sion prevention, ma intenance and storage.
Pay attention to additiona l information con
cerning the battery. Refer to~
page 243.
Avoid damaging the
vehicle
When you a re driving on poor roads, or over
curbs, steep ramps, etc., make certain that low-lying parts such as spoilers and exhaust
system parts do not bottom out and get dam
aged.
This is especially true for vehicles with low
slung chassis (sports chassis)* and fully load
ed vehicles.
Driving through water
on roads
Note the following to avoid vehicle damage
when driving through water, for example on
flooded roads :
- The water must not be any higher than the
bottom of the veh icle body.
- Do not drive faster than wa lking speed.
A WARNING
After driving through water, mud, slush,
etc., the brakes may be slow to take effect
because of wet brake rotors and pads. Dry
-
Drivin g and environment 209
the brakes first by braking carefully to re
store the full braking effect.
(D Note
- Vehicle components such as the engine,
transmission, suspension or electrical
system can be severely damaged by driv
ing through water.
- Always switch off the Start-Stop-System
when driving through water~
page 88.
(D Tips
-Check the depth of the water before driv
ing through it .
- Do not stop the vehicle, drive in reverse
or switch the engine off when driving
through water.
- Keep in mind that oncoming vehicles may create waves that raise the water
level and make it too deep for your vehi
cle to drive through safely .
- Avoid driving through salt water because
it can cause corrosion.
Operate your vehicle
economically and minimize pollution
General
Your personal style of driving will determine
t he economy of your vehicle , as well as ex
haus t and noise levels.
Fuel economy, environmental impact, and
wear on your engine, brakes and tires largely
depend on three factors:
- your personal driving style
- operating conditions
- technical limitations
If you ant icipate what you need to do next and
drive econom ically, you can easily cut your
fuel consumpt ion by 10-15 percent . Th is sec
tion w ill give you some tips on how you can
help the env ironment and your pocketbook. •
•