instrument cluster AUDI A8 2015 User Guide

48 Clear vision
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights a ctivation time -You can adjust if
the head lights switch on
Early , Med. or Late
according to the sensitivity of the light sensor.
Audi adaptive light* -You can switch adaptive
light
On and Off.
Automatic high beams*
You can switch the high beam assist on and
off .
Daytime running lights
USA models :
You can switch the daytime run ­
ning lights
on and off .
Canada models:
The function cannot be
turned off. It is activated automatica lly each
time the ignition is switched on . This menu
item is shown "greyed out".
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when you switch the
ignition off and open the driver's door. To turn
the function on, select
Lights when leaving
car> On.
The leaving home function illuminates the
area outside the vehicle when you un lock the
ve hicle . To turn the funct ion on, select
Lights
when unlocking car > On .
The coming home and leaving home functions
on ly operate when it is dark and the light
switch is in the
AUTO position.
Turn signal and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
Fig. 42 Tu rn signal and high beam lever
The turn signa l and high beam lever has the
following functions:
Turn signals ¢ 9 (D@
.. Push the lever up as far as it can go to turn
on the right turn signal or down to turn on
t he left turn signal
¢ fig. 42 .
N 0 ... 'i' :r
~
.. Move the lever briefly until you meet res ist·
ance and re lease it to flash three times.
.. Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam [D @
.. Push the lever forward to switch on the high
beam (vehicles with high beam assist*
¢page49).
.. Pull the lever back towards you to switch off
the high beam .
Headlight flasher [D ©
.. Pull the lever toward the steering wheel to
use the headlight flasher.
Notes on these features
-The turn signals only work w ith the ignition
switched on. The indicator lights
ID or iPJ
in the instrument cluster ¢page 11 also
blink.
- After you have t urned a corner, the turn sig -
na l switches off automatically .
Ill>

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-The high beam works only when the head­
lights are on. The indicator light
II in the
instrument cluster ill uminates when the
high beams are on.
- The
headlight flasher works only as long as
you hold the lever -even if there are no
lights turned on. The indicator light
II in
the instrument cluster illum inates when you
use the head light flasher .
A WARNING
Do not use the high beam o r headlight
flasher if you know t hat these could blind
on coming traffic.
High beam assist
A ppl ies to vehicles : wit h high bea m ass ist
-
The high beam assist automatically switches
the high beams on or off, depending on the
surroundings and traffic conditions.
F ig. 4 3 Tu rn signa l an d h igh beam lever: Turning on
and off t he h igh beam ass ist
Activating high beam a ssist
Requirement : The light sw itch must be in the
AUTO position, the low beam headlights must
be on and the high beam assist must be
sw itched on in the Infotainment~
page 47.
.. Press the lever forwards (Din order to acti-
vate the high beam ass ist. The indicator
light
IIJ turns on in the inst rument cluste r
display and the high beams switch on or off
automati ca lly. The indica to r ligh t
Iii turns
on if the high be ams were switched on.
Switching the high beams on /off
manually
R equi rement : Hig h beam ass ist is activated.
Clear v is ion 49
If the high beams d id not swi tch on/off auto ­
matically when expected, you may instead
switch them on/off manually:
.. To swi tch the high beams on manually, press
the lever forwa rds (D. The indicato r light
Bl
turns on.
.. To switch the high beams off manually, pull
the lever backwards @. The high beam as­
sist is deactivated .
Operating the headlight fla sher
.. To operate the flashe rs while the high beam
assist is active and the high beams are
sw itched off, pull the lever into posit ion @.
The high beam assist will remain active.
Messag es in the instrument cluster
di splay
Headlight ass ist: System fault
Drive to your authorized A udi dealer immedi­
ate ly to have the ma lfunction corrected. Yo u
can still switch the high beams on or off man­
u ally.
Headlight assi st: Unavailable . No camera
view
T he came ra v iew is b locked, for example by a
sticker o r debr is.
The sensor is loca ted between the inter io r
r earvi ew mirror and the w indshield . There­
fo re, do not p lace a ny s tick ers i n this a rea on
t h e windsh ie ld.
Service setting
There is a different sensit iv ity sett ing for serv­
ic ing . T hi s sett ing can be activated by pressing
and holding the b utton on the int erio r r ear­
view m irror for more tha n 18 seconds. The
L E D next to the button blinks th ree times.
If
yo u have accidentally se lec ted this service
function, the origi nal sensitivity will be auto­
matically restored the next t ime yo u sw itch
the ignit ion on.
IJ>,

(D Note
To avoid damage to the heating elements in the seats, do not kneel on the seats or
place heavy loads on a small area of the
seat.
Setup
The climate control system setup is accessed
through the MMI.
• Select: I CARI function button> Car systems
control button > A/C.
Rear cabin settings*
When this function is selected, all sett ings for
the rear can be adjusted through the climate
control system in the cockpit . The climate
control system settings cannot be adjusted in
the rear seat at the same time. This function
switches off after a certain period of time or
when one of the dials in the cockp it is press­
ed .
Auto recirculation*
Warm and cold 81
Solar roof*
Parking ventilation is controlled automatically
in the
auto setting .
When the ignition is off, solar-powered park­
in g ven tilat ion may switch on, as long as
- there is sufficient sunlight,
- the outside temperature is not too low,
- the sunroof is closed or tilted and
-auto (MMI) is selected .
~ Steering wheel heating
Applies to vehicles : wi th hea ted stee ring wheel
The steering wheel rim can be heated .
Fig. 86 Steering col umn: steering w hee l h eating but-
The sensitivity level of the automatic recircu-ton
lation mode can be set at various levels from
off to sensitive . The recirculation mode l""" I is
controlled on automatically. You must press
the~ button if fog forms on the w indows .
Footwell temperature
You can adjust the footwe ll temperature so
that it is cooler or warmer.
Windshield heat*
When the defroster~ is switched on and the
Auto setting is selected, the windshie ld de­
froster is controlled automatically .
Supplementary heater*
The supplementary heater warms the inter ior
of vehicles with diesel engines* more quickly.
The supplementary heater is controlled auto­
mat ica lly in the
Auto setting. •
Press the
lj] button to switc h steer ing wheel
he ating on/off. The message
Steering wheel
heating on!/Steering wheel heating off!
appears in the instrument cluster display.
T he temperature is maintained at a constant
level when steering wheel heating is switched
on.
The steering wheel heating settings are stor­
ed automatically and assigned to the remote
control key that is in us e.

84 On th e road
Emerg ency off
If necessary, the engine can be sw itched off
with the selector lever in the R, Dor S posi ­
tions . The engine stops if you press the
I START ENGINE STOP ! button at speeds below
6 mph (10 km/h).
A WARNING
- Never turn off the eng ine before the ve­
hicle has come to a complete stop . The
full function of the brake booster and the
power steering is not quaranteed. You
must use more force to turn or brake if
necessary. Because you cannot steer and
brake as you usual ly would, this could
lead to crashes and serious injur ies.
- For safety reasons, you should always
park your vehicle with the se lector lever
in P. Otherwise, the vehicle co uld inad­
vertent ly roll away .
- After the engine has been switched off, the radiator fan can continue to run for
up to 10 min utes - even with the ign it ion
switched off. It can a lso switch on aga in
after some time if the coolant tempera­
ture rises as the result of a heat buildup or if the engine is hot and the engine
compartment is addit ionally heated by
the sun's rays.
(D Note
Do not stop the engine immed iate ly afte r
ha rd or extended dr iving. Keep the engine
r u nning for approx imately two m inutes to
prevent excessive heat build-up.
Driver message in the instrument
cluster display
T urn off ignition before le aving car
This message appears and a war ning tone
sounds if you open the driver's door when the
ignitio n is switched on.
Pr ess brake p edal t o start engin e
This message appears if you press the
I STAR T ENGINE S TOP ! button to start the en- gine and do not depress the brake pedal.
The
engine can only be started if the brake pedal
is depressed.
Ill I s key in th e vehi cle?
If the indicato r light turns on and the mes­
sage appears, the remote control key was re­
moved from the vehicle whi le the engine was
runn ing .
If the igni tion key is not in the veh i­
cle you will not be able to switch on the igni­
tion or restart the engine after it has been switched off. You will a lso not be able to lock
the vehicle from the outs ide.
Shift to P, othe rwi se vehicle can roll away.
Door s do not lock if lever i s not in P.
T h is dr iver message appears for safety rea­
sons if the transmission has not been shifted
to the P position when you switch the ignition
off. Move the selector lever to the P position.
Otherwise the vehicle is not protected from
ro lling and cannot be locked.
II Key i s not recognized . Hold b ack of key
again st m arked are a. See ow ner' s m anual.
If the indicator l ight turns on and this mes­
sage appe ars, there is a ma lfunct ion
¢ page 85.
Tu rn off i gnition before leaving car. Ba ttery
i s di sc harging
Th is message appears if the driver's door is
opened wh ile the ignition is switched on. Al­
ways switch off the ign it ion if you a re leav ing
the vehi cle. See also
¢page 89 .
Shift to P and turn off ignition before l eav­
ing car, otherwi se vehicle c an roll away
This message appears if the driver's door is
opened wh ile the ignition is switched on and
the selecto r lever is not in the P position. Shift
the selector lever into the P pos ition and
switch off the ignit ion when you exit the vehi­
cl e. Otherw ise the vehicle cou ld rol l. See also
¢page 89.

Starting the engine if there is a
malfunction
It may not be possible to start the engine un­
der certain circumstances , for example if the
battery in the vehicle key is drained , if inter ­
ference hos affected the key or if there is a
system malfunction.
i :c _ ____ ;&
Fig. 89 Center console/master key : starting the engine
if th ere is a m alfunction
Requirement : The message Key not re cog­
nized. Hold b ack of key against marked area.
See owner's manual.
must appear and the in­
dicator light
II must switch on .
"' Hold the master key vert ica lly in the loca­
tion indicated
y >>) c::> fig. 89.
"' Press the brake pedal i=:> A in Starting the
engine on page 83 .
"'Press the j ~s_T_A_R_T_E_N_G _I_N _E_ S_T_O_P~I button . The
engine will start .
"' Drive to your au thor ized Audi dealer imme­
diately to have the malfunct ion corrected .
(D Tips
You can view the message again by press­
ing the
! START ENGINE STOP I button.
On the road 85
Electromechanical
parking brake
Operation
The electromechanical parking broke replaces
the hand broke.
Fig. 90 Center co nsole: Parking b rake
"' Pull on the switch © i=:> fig. 90 ® to apply
the parking brake. The indicator lights in the
switch and. (USA models)/ . (Cana-
da models) in the instrument cluster illumi­
nate .
"' With the ignition switched on, step on the
brake peda l or the accelerator pedal and
press the switch <®lat the same time to re­
lease the parking brake . The indicator lights
in the switch and. (USA mode ls)/ . (Can­
ada models) in the instrument cluster go
out .
Your vehicle is equipped with an electrome­
chanical parking brake. The parking brake is
designed to prevent the vehicle from rolling unintentionally and replaces the hand brake.
In addit ion to the normal functions of a tradi­
tiona l hand brake, the electromechanical
parking brake provides vario us convenience
and safety functions .
When starting from rest
-The integral start ing assist helps you when
driving by automatically re leasing the park­
i ng brake
i=:> page 86, Starting from rest.
- When start ing on inclines , the starting as-
sist prevents the vehicle from unintentiona l-
ly rolling back. The braking force of the
parking brake is not re leased until sufficient
111>

88 On the road
switched off. More force is required to
stop and to steer the vehicle.
- To reduce the risk of injuries, make sure
that the Start-Stop-System is turned off
when working in the engine compart­
me nt¢
page 89.
(D Note
Always switch off the Start-Stop -System
when driving through water ¢
page 89.
Starting/stopping the engine
Applies to vehicles: with Start-Stop-System
Fig . 91 In strument duster : eng ine switc hed off (stop
phase)
~ Slow the vehicle to a stop using the brake
and keep pressing the brake pedal. The en­
gine w ill switch off. The
11] indicator light
appears in the information line in the instru­
ment cluster display.
~ When you take your foot off the brake ped­
al, the engine restarts . The ind icator light
turns off.
Additional information
The engine w ill switch off in the P, D, N and S
positions as well as in manua l mode. In the P
position, the e ngine will also remain off if you
take your foot off the brake pedal. The engine
starts again when you select another se lector
lever position and take your foot off the brake
pedal.
If you select the R position during a Stop
phase, the engine will start again .
Shift from D to P quickly to prevent the engine
from starting unintentionally when shifting
through R. You
can determine for yourself if the engine
will stop or not by reducing or increasing the
amount of force you use to press the brake
pedal. For example, if you only lightly press
on the brake pedal in stop-and and-go traffic
or when turning, the engine will not switch off
when the vehicle is stationary. As soon as you
press the brake down harder, the engine wi ll
switch off.
General information
Applies to vehicles: with Start-Stop-System
The standard Start-Stop-mode can be cancel­
led for different system-related reasons.
Fig. 92 Instrument cluster: eng ine -Stop temporarily
unavailable
Engine will not switch off
Before each stop phase, the system checks if
certain conditions have been met. For exam­
ple, the eng ine will
not be switched off in the
following situations:
- The engine has not reached the minimum
requ ired temperature for Start-Stop-mode.
- The interior temperature selected by the A/C
system has not been reached.
- The outside temperature is extremely high/
low.
- The windshield is being defrosted
¢page 81.
-The parking system* is switched on.
- The battery charge level is too low.
- The steering wheel is sharply turned or
there is a steering movement.
- After engaging the reverse gear.
- On sharp incl ines.

The@j indicator light appears in the informa ­
tion line in the instrument cluster display
<:!)fig. 92 .
Engine automatically restarts
The stop phase is interrupted in the following
situations, for examp le. The engi ne restarts
without any action by the driver.
- Th e interior temperature varies from the
temperatu re selected in the A/C system.
- The windshield is being defrosted
r::!) page 81 .
-The brake pedal is pressed several times in a
row.
- The battery charge level becomes too low.
- High power consumption .
Switching the ignition off automatically
To prevent the battery from draining, the igni­
tion will switch off
automatically when all of
the following conditions have been met:
- The vehicle has al ready been driven.
- The eng ine has been turned off by the Start-
Stop-System*.
- The driver's door is opened.
- The driver's seat belt is removed .
- The brake pedal is not pressed down.
- The vehicle is stationary .
In this case, the activated low beam will be re­
placed by the side marker lights. The side
marker lights will switch off after approxi­
mately 30 minutes or when you lock the vehi­
cle .
If the Start-Stop System has
not turned off
the engine or if you have switched the Start­
Stop system off manually, the ignition w ill
not
be automatically switched off and the engine
will cont inue to run
r::!) .&. .
A WARNING
Never allow the engine to run in confined
spaces - danger of asphyxiation.
(D Tips
If you shift into the D, N or S positions af­
ter shift ing into reverse, the veh icle must
On the road 89
be driven faster than 6 mph (10 km/h) in
order for the engine to switch off again.
Switching the Start-Stop-System on/off
manually
App lies to vehicles: wit h Start -Stop -System
If you do not wish to use the system, you can
switch it off manually.
Fig. 93 Center console: Start -Stop -System button
.,. To switch the Sta rt-Stop-System off/on
manually, p ress the
ICA.> ••I button. The L ED in
the button turns on when the system is
sw itched off.
(D Tips
If you switch the system off during a stop
phase, the engine will start again auto­
ma tically .
Messages in the instrument cluster
display
Applies to vehicles: wit h Start-Stop-Syste m
Start-Stop system deactivated: Please re­
start engine manually
This message appears when specific condi­
tions are not met during a stop phase and the
Start-Stop-System will
not be able to restart
the engine. If the Dor R selector lever posi­
tions were engaged, P will be selected auto­
matically . The engine must be started with
the
I START ENGINE ST OP ! button.
Start-Stop system: System fault! Function
unavailable
There is a malfunction in the Start-Stop-Sys­
tem. Drive the vehicle to an authorized repair .,.

90 On the road
facility for servicing as soon as possib le to
correct the malfunction.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed.
The speed warning system warns you if you
are exceeding the maximum speed that you
have set . You will hear a warn ing tone when
your speed exceeds the stored value by ap­ proximately 3 mph (3 km/h). An indicator
light. (USA models) . (Canada models) in
the instrument cluster display also turns on at
the same time. The indicator light./.
turns off when the speed decreases below the
stored maximum speed.
Sett ing a threshold is recommended if you
wo uld like to be reminded when you reach a
certain maximum speed . Situations where you
may want to do so include driving in a country
with a general speed limit or if there is a
specif ied maximum speed for winter tires.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you should still
watch the speedometer to make sure you
are not driving faster than the speed lim it.
Setting the threshold
You can set, change and delete the threshold
in the MMI.
.. Se lect : ICAR lfunction button> Car systems
control button > Driver assist > Speed warn­
ing.
You can set any threshold between 20 mph
(30 km/h) and 150 mph (240 km/h). Settings
can each be adjusted in increments of S mph
(10 km/h).
Cruise control
Switching on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30kmlh) .
0
•
~
0
Fig. 94 Control leve r with set b utton
Fig. 95 Display: Se lected speed
.. Pull the lever to position (D c::> fig. 94 to
sw itch the system on.
.. Drive at the speed you wish to set.
.. Press button @ to set that speed.
T he stored speed and the indicator light
II (US models) ;El (Canadian mode ls) ap­
pear in the instrument cluster display
c::> fig. 95 . The display may vary, depending on
the type of display in your veh icle .
T his information is also shown briefly in the
Head-up Display*.
Th e speed is kept constant via an engine out­
put adjustment or active brake intervent ion.
WARNING
-Always pay attention to traffic even when
the cruise control is switched on. You are
a.lways respons ible for your speed and
Ill-

94 Audi adaptive cruise control and braking guard
@ is located in front of that vehicle, the sys­
tem will not react to the stationary vehicl e.
Audi adaptive cruise
control
Description
Applies to vehicles: with Audi adaptive cruise control
Fig. 99 Detectio n range
What can adaptive cruise control do?
The adaptive cruise control system uses video,
radar and ultrasou nd . Moving vehicles ahead
can be recognized up to about 650 feet (200 m) away.
On open roads w ith no traffic, adaptive cruise
control works like a regular cruise control sys­
tem . The stored speed is maintained . When
approaching a moving vehicle detected up
ahead, the adaptive cruise control system au­
tomatically s lows down to match that vehi­
cle's speed and then maintains the distance
that the driver previous ly stored. As soon as
the system does not detect a vehicle up
ahead, adaptive cruise control accelerates
back up to the stored speed.
In stop-and-go traffic, adapt ive cru ise control
can brake until the vehicle stops and acceler ­
ate again under certain conditions and if this
is possible within the system's limits and ca­
pabilities ¢
page 96. Adaptive cru ise control
will not make an emergency stop .
Which functions can be controlled?
When you switch adaptive cruise contro l on,
you can set the current speed as the "control
speed" ¢
page 94, Swi tching on and off.
When driving, you can stop cruise control
¢
poge 96 or change the speed ¢ page 95
at any time.
You can also set the distance to the object
ahead and set the adaptive cruise control driv­
ing program ¢
page 96.
Switching on and off
Applies to vehicles: with Audi adaptive cruise control
Fig. 100 Selector lever: swi tc hin g on/off
Fig. 101 Instrument cl uste r: adapt ive c ruise contro l
You can set any speed between 20 mph and
95 mp h (30 and 150 km/h).
Ind icator lamps and messages in the instru ­
ment cluster d isplay inform you about the cur­
rent system status and settings.
An additional indicator appears in the Head­
up D isp lay* .
Switching adaptive cruise control on
.,. Pull the lever toward you into position (D
¢ fig. 100 . ACC standby appears in the in ­
strument cluster display .
Setting the speed and activating
regulation
.,. To set the current speed, press the ISETI but­
ton ¢
fig. 100 . The set speed is shown in the 1111-

102 Audi active lane assist
Activating and deactivating
Applies to vehicles: with active lane assist
-
I
Fig. 107 Turn signal lever: Act ive lan e ass ist button
Fig. 108 Windshield: Active lane assist camera viewin g
win dow
~ Press the ¢ fig. 10 7 button to activate or
deactivate the system . The indicator light
• or. in the instrument cluster will illu­
minate or go out.
Instrument cluster indicator light
• Ready: The indicator light shows that the
system is ready to use . The system can now
warn you if you are about to cross a known
lane marker line .
• Not ready: The ind icator light shows that
the system is turned on but unable to send a
warning . This can be due to the following :
- There is no lane marker line .
- The relevant lane marker lines are not de-
tected (for example, markings in a construc­
tion zone or because they are obstructed by
snow, dirt, water or backlight ing).
- The vehicle 's speed is below the speed need ­
ed to activate it, which is about 40 mph (65
km/h) .
- The lane is narrower than about 8 ft . (2 .5 m)
or wider than 15 ft (4 .5 m).
- The curve is too sharp . - The driver's hands are not on the steering
wheel.
(D Tips
Make sure the camera's field of view
¢
fig. 108 is not obstructed by stickers,
deposits or anything else. For information
on cleaning, refer to
¢ page 214 .
Active lane assist display in the
instrument cluster
Applies to vehicles: wit h active lane assist
Fig. 109 D isp lay : Act iv e lane ass ist is swi tc h ed on a nd
is wa rnin g
Fig. 110 Instrumen t cl uster: Active lane as sis t is
s witch ed o n but not re ad y to provid e wa rnin gs
You can call up the active lane assist display
using the buttons in the multifunction steer­
ing wheel ¢
pag e 23.
When active lane assist is switched on, the
system indicates which lines are detected by
displaying solid lines on the left and/or right
side of your vehicle :
ll>