air condition AUDI A8 2017 Owners Manual

Cockpit over view
& WARNING
Do not tow your veh icle when there is a mal­
function in the electronic steering lock -this
increases the risk of an accide nt.
© -Engine start system
• Engine start sy ste m fault . Plea se contact
dealer
Do not switch the ignit io n off because you may
not be able to switch it o n aga in .
Drive to an authorized Aud i dea ler or a uthorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
1111 Engine start system fault. Please contact
dealer
There is a mal func tion in the eng ine start ing sys­
tem .
D rive to an a uth o riz e d Aud i de aler or a uth o rized
Au di Serv ice Facility immedi ately to have t he
malfunct ion corre cted .
~ Air suspension
• Air su spension : System fault Driving slowly
at ma ximum 35 mph is possible.
There is a malfunction that can resul t in restrict ­
ed d riving stability .
D rive to an a uth o rized Au di dea le r or a uthorize d
Aud i Serv ice Facility immedi ately at a ma xim um
speed of 3S mph (6 0 km/ h) to have the m alfu nc ­
tion corrected.
• Air suspen sion : Service mode. Vehicle can
onl y be moved with restriction s
Carefully drive to your author ized A udi dealer or
author ized Audi Se rvice Facility immed iate ly to
have the serv ice mode deactivated.
rl Air su spension : System fault
There is a system malfunct ion that can result in
restricted d riving stability or reduced gro und
clearance.
22
Drive to an au thori zed A udi dealer or authori zed
Audi Se rvice Facility immediate ly to have the
malfunction cor rected.
rl Air suspension : Vehicle i s too low. Ground
clearance limited
The gro und clea rance is very low due to a system
malfunction . Wai t unti l th e air su sp ension sys ­
tem has restored normal g ro und clear ance. Oth­
erwise, conditions s uch as an uneven road surface
can lead to ve hicle damage.
. ;;.l u Electronic Stabilization Control (ESC)
If the G) ind icator light blinks while driving, the
ESC or ASR (Anti-Slip Regulation) is act ively regu­
l ating.
If the
G) indicator light turns on, the system has
switched the ESC off. In th is case, you can switch
the ignit ion off and then on to switch the ESC on
again. The i ndicator light tu rns off when the sys­
tem is functioning fully .
If the
II ind icator light turns on, the ESC was
switched off using the
lli] b utton o page 126.
Stabilization cont rol (ESC/ABS) : malfunction!
See owner's manual
I f the If.) ind ic a tor light and t he A BS indica to r
li gh t~ (U SA mode ls)
I [IJ (Canada models)
turn o n an d this message appears, there is a mal­
functio n in the ABS system or electro nic differen­
tia l lock. This also causes the ESC to malfunction.
The brakes still function with their normal power, but ABS is not active .
Drive to an authorized A udi dealer or authorized
Audi Se rvice Fac ility immediate ly to have the
malfunction corrected .
& WARNING
If the ... (USA models) • (Canada mod ­
e ls) bra ke system indicator light turns on to­
ge the r with the ABS and ESC in dicator ligh ts,
the ABS a nd ESC r egulating fu nction may
ha ve malfunc tioned. Fu n ct io ns t hat stab ilize
t he vehicle are no l onger av aila ble. This co uld
cause t he vehicle to swerve, which increases

Cockpit overview
On-Board Diagnostics
Fig. 19 Location of Data Link Connector (DLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identified and the fault stored as a
code in the control module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop­
erly closed
¢ page 269.
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for OBD).
In order to connect the special diagnostic equip­ ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release
¢ fig. 19.
Your authorized Audi dealer or a qualified service
station can interpret the code and perform the
necessary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
-
Your vehicle may be factory equipped with tires
that are rated for a maximum speed of 130 mph (210 km/h). This is less than the maximum speed
of your vehicle . To reduce the risk of sudden tire
26
failure and loss of control if the vehicle is operat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter. The electronic speed
limiter prevents your vehicle from going faster
than the tire speed rating. For more information
¢ page 290.
If the engine control unit receives faulty vehicle
road speed signals, the Malfunction Indicator
Lamp (MIL)
¢'4 will illuminate. If this occurs,
contact the nearest authorized Audi dealer for
ass istance.
58
Your vehicle's top speed is electronically limited
to 155 mph (250 km/h).
If the engine control unit receives faulty vehicle
roadspeed signals, the Malfunction Indicator
Lamp (MIL)
¢'4 will illuminate. If this occurs,
contact the nearest authorized Audi dealer for
assistance.
A WARNING
Always observe the posted speed limits and
adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your vehicle faster than the maximum speed rating
of the ti res installed.
-

Opening and closing
Central locking
Description
You can lock and unlock the veh icle centrally . You
have the following options:
- Remote control key¢
page 30
-Sensors in the door handles* ¢ page 30
-Lock cylinder in the driver's door¢ page 32
-Inter central locking switch ¢ page 31
Turn signals
The turn signals flash tw ice when you un lock the
vehicle and flash once when you lock the vehicle.
If the vehicle is unlocked and the flashing contin­
ues, then
- one of the doors, the luggage compartment lid
or the hood is open.
- the ignition is still switched on .
- the selector lever is not in the P position
Auto Lock
The Auto Lock function locks all doors and the
luggage compartment lid once the speed has ex­
ceeded approximately 15 km/h.
The vehicle can be unlocked if the opening func­
tion in the centra l locking system switch is used
or one of the door handles is pulled. The Auto Lock function can be switched on and off in the
Infotainment system ¢
page 32.
In the event of a crash with airbag deployment,
the doors will also automatically unlock to allow
access to the vehicle.
Selective door unlocking
The doors and luggage compartment lid will lock
when they close. You can set in the Infotainment
system whether only the driver 's door or the en­
tire vehicle should be unlocked when unlocking
¢page 32.
Unintentionally locking yourself out
0 co The following conditions prevent you from lock-....
~ ing your remote control key in the vehicle: N .... 0 0 :c ' Opening and closing
-If the driver's door is open, the vehicle cannot
be locked by pressing the~ button on the re­
mote contro l key or touching the locking sensor
on a door.
- When locking using the~ button in the central
locking switch, the vehicle will not lock if a door
is open
¢ page 31.
-If the most recently used convenience key* is in
the luggage compartment, the luggage com­
partment lid automatically unlocks again after
closing it¢
page 33 . The emergency flashers
blink four times.
Do not lock your vehicle with the remote control
key or convenience key* until all doors and the
luggage compartment lid are closed . This helps
to prevent you from locking yourself out acc iden­
tally .
Closing aid on the doors*
The vehicle doors are equipped with closing aids.
When closing a door, you only have to let it fall
lightly into the latch . It then closes automatically
¢ &_ .
.&, WARNING '"----
- When you lock your vehicle from outs ide,
nobody -espec ially children -should rema in
inside the vehicle. Remember, when you
lock the vehicle from the outside the win­
dows cannot be opened from the inside .
- When you leave the vehicle, always take the
ignition key with you. This will prevent pas­
sengers (children, for examp le) from acci­
dentally being locked in the vehicle should
they accidentally press the power locking switch in the doors.
- Do not leave children ins ide the vehicle un­
supervised. In an emergency it would be im­
possible to open the doors from the outside
without the key.
- Applies to vehicles with power side door
closer*:
- When closing a door, make sure nothing
can interfere with the door. This could
cause serious personal injury.
27

Lights and Vision
Q/P -Adjusting the left/right exterior mirror.
Move the knob in the desired direction.
(@. -Heat ing the mirror glass depending on the
outside temperature .
9 -Folding exterior mirrors* . In the Infotain­
ment system, you can select if the mirrors fold in
automatically when you lock the vehicle
¢page 32.
Front passenger's exterior mirror tilt
function*
To help you see the curb when back ing into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger's outside
mirror.
You can adjust the tilted mi rror surface by turn­
ing the knob in the desired direction. When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph
(15 km/h) or turn the ignition off.
A WARNING
Curved mirror surfaces (aspheric or convex*)
enlarge the field of vision. However, they
make objects in the mirror appear smaller
and farther away. Your may estimate incor­
rectly when you use these mirrors to gauge
your distance from the vehicles behind you
when changing lanes, wh ich increases the risk
of an accident.
(D Note
- If the mirror housing was moved by outs ide
forces (such as an impact when maneuver­ in g), you must use the power fold ing func­
tion to fold the mirror all the way out. The
mirror housing must not be moved back in­
to place by hand because this would impair
the function of the m irror mechanism.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
48
Never fold power fold ing exterior mirrors by
hand . On ly fold them in and out using the
power controls.
(D Tips
- If the power adjusting function malfunc­
tions, the glass in both mirrors can be ad­
justed by pressing on the edge of it by hand.
- The exterior mirror settings are stored with
the memory function*¢
page 59.
Dimming the mirror
Fig. 51 Automatic dimm ing rearv iew mirror
0
~ 0 :i:
a'i
.. To dim the interior rearview mirror and both ex­
terior mirrors*, press the button @. The LED @
turns on. The interior rearv iew mirror and exte­
r ior mirrors* dim automatically when light
shines on them, for example from headlights
on a vehicle behind you.
A WARNING
Electrolyte fluid can leak out from broken
mirror glass. This liqu id can irritate the skin,
eyes and respiratory system. If there is con­
tact with the fluid, flush immediately with
p lenty of water . Consult a physician if neces­
sary.
-
- Repeated or long-term exposure to electro­
lyte fluid can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of the
doors and w indows as wide as possible.
- If electrolyte fluid enters the eyes, flush
them thoroughly with a large amount of

Adjusting the temperature
Temperatures between 60 °F ( +16 °C) and 84 °F
(+28 °C) can be set . Outside of this range,
LO or
HI will appear in the climate control system dis­
p lay . At both of these settings, the climate con ­
trol system runs continuously at maximum cool­
ing or heating power. There is no temperature
regulation.
~ Adjusting the amount of air
You can adjust the airf low manually to su it your
needs. The blower should always run at a low set ­
ting to prevent the windows from fogging and to
ensure a continuous exchange of air inside the
vehicle. To have the airflow regulated automat i­
cally, press the
IAUTO I button.
~ Adjusting the air distribution
You can manually select the vents where the air
will flow. To have the a ir distribution regu lated
automatically, press the
IAUTO ! button.
[il /~*Adjusting seat heating/ventilation*
Pressing the button switches the seat heating/
venti lation on at the highest setting (level 3). The
LEDs indicate the temperature level. To reduce
the temperature, press the button aga in. To
sw itch the seat heating/venti lation off, press the
button repeatedly until the LED turns off.
After 10 minutes, the seat heating/ventilation
automatically switches from level 3 to level 2.
l The windshield and side windows are defrosted
or cleared of condensation as quickly as possible.
The maximum amount of air flows mainly from
the vents below the windshield. Recirculation
mode switches off. The temperature should be
set to approximately 72 °F (22 °().
The
IAUTO I button switches the defroster off .
IQiil R EARI Switching the rear window defogger
on and off
The rear window defogger only operates when
~ the engine is running. It switches off automati-....
~ cally after 10 to 20 minutes, depending on the N
8 outside temperature. 0 :c ' Warm and cold
To prevent the rear window defogger from
switching off automatica lly, press and hold the
llliil REAR ! button for more than three seconds .
This is stored until the ignition is switched off.
I SYNC! Synchronization*
When synchron ization is switched on, the set­
tings for the driver's side are applied to the front
passenger's side (except for seat heating/ventila­
t ion*). The rear is also synchronized in vehicles
with the 4- zone deluxe automatic climate control
system*. Synchronization switches off if the set­
t in gs are adjusted on the front passenger's side
or in the rear*.
You can synchronize the sett ings in a row by
pressing and holding a knob. For example, to ap­
ply the sett ings for the front passenger's side to
the driver's side, press and hold the knob on the
front passenger 's side .
Vents
You can open or close the center and rear vents in
the cockpit and the vents in the rear center con­
sole and door pillars using the ridged thumb­
wheels. The levers adjust the direction of the air­
flow from the vents.
Residual heat
You can act ivate the residual heat function when
the ignition is switched off by pressing and hold­
i ng the ~ button. The residual heat from the
coolant is used to heat the vehicle interior . T he
residual heat function switches off automatically
after about 30 minutes.
_&. WARNING
- You should not use the recirculation mode
for an extended period of time since no
fresh air is drawn in. With the air-condition ­
ing switched off, the windows can fog up,
which increases the risk of an acc ident.
- Individuals with reduced sensit ivity to pain
or temperature could develop burns when
using the seat heating function. To reduce
the risk of injury, these individua ls should
not use seat heating .
71

Ass is t
system may have detected a vehicle in another
lane that is not adjacent to your current lane.
- If you are driving through a curve. Side assist may react to a vehicle that is one lane over
from th e adjacent lane .
- If s ide assist reacts to other objects (such as
high or d isplaced guard ra ils).
- In poor weather condit ions. The side assist
functions are limited.
Do not cover the radar sensors <=>
fig. 121 with
stickers, deposits, bicycle wheels o r othe r ob ­
jects, beca use they wi ll impair the function. Do
not use side ass ist when towing a trailer. For in­
formation on cleaning, see <=>
page 306.
A WARNING
-Always pay attention to traffic and to the
area around your vehicle. Side assist cannot
rep lace a driver's attention. The driver alone
is a lways responsible for lane changes and
similar d riving maneuvers .
- In some situat ions, the system may not
func tion or its funct ion may be limited . For
example :
- if vehicles are approaching or being left
behind very quickly. The display may not
turn on in t ime .
- In poor weather conditions such as heavy
rain, snow or heavy mist .
- On very wide lanes, in tight curves, or i f
there is a rise in the road surface. Vehicles
in the adjacent lane may not be detected
because they are outs ide of the sensor
range.
- Audi side ass ist cannot detect a ll vehicles
under a ll condit ions, which can increase the
risk of accidents.
- Please note that side assist only displays ap­ proaching vehicles or vehicles in your blind
spot if your vehicle is traveling at least
19 mph (30 km/h) .
- In certain situations, the system may not
work or its function may be limited. For ex ­
amp le:
- The display may not turn on at the rig ht
time if veh ides are approaching or passing
very q uick ly .
106
-
- In poor weather conditions, such as heavy
rain, snow or fog .
- In very wide lanes , in tight c urves or when
there are slopes in the roadway, vehicles
i n the ne ighboring lanes may not be de­
tected because they a re outside of the
sensor range .
(D Note
The sensors can be d isplaced by impacts or
damage to the bumper, wheel housing and underbody. This can impair the system. Have
an authorized Audi dealer or author ized Audi
Service Fac ility check their f unct io n.
@ Tips
- If the w indow glass in the dr iver's door or
front passenge r's door has been tinted, the
display in t he exterior mirror may be incor­
rect .
- For an explanat ion on co nfo rm ity w ith the
FCC regulations in the Un ited States and the
Indust ry Canada regulatio ns, see
~page 339.
Switching on/off
Applies to: vehicles wi th A ud i side assist
F ig . 122 D river 's doo r: side as sist but ton
.,. Press the button to sw itch the system on and
off <=>.&
in General information on page 106 .
The LED in the button tur ns on when side assis t
is swi tched on.

0 co .... N ,..... N .... 0 0 :c ' depends on the driving mode selected, steering
movements, the driver's braking and accelera­
tion, and as the road surface, vehicle speed and load. A sporty setting is generally used in vehicles
with adaptive air suspension sport*.
The vehicle ground clearance depends on the
mode selected and the speed. When you are in
the auto or dynamic mode, the highway setting is
activated when you drive above 75 mph (120 km/
h) for more than 30 seconds. The ground clear­
ance is increased automatically if the speed
drops below 44 mph (70 km/h) for more than 120 seconds .
Steering
The power steering adapts. Indirect steering that
moves easily as in comfort mode is especially
suited to long drives on a highway. The dynamic
mode provides sporty, direct steering .
Applies to: vehicles with dynamic steering
The steering ratio changes based on vehicle
speed in order to maintain optimum steering ef ­
fort for the driver at all times . This sets the steer­
ing to be less sensitive at higher speeds in order
to provide improved vehicle control. At reduced
speeds, steering is more direct in order to keep
the steering effort as minimal as possible when
the driver is maneuvering the vehicle. At low and
average speeds, dynamic steering* additionally
provides more responsive steering performance.
Sport differential*
As a component of the all wheel drive system
(quattro)
~ page 130, the sport differential dis­
tributes the driving power to the rear axle de­
pending on the situation. The distribution of
power varies from balanced (comfort) to sporty
(dynamic) depending on the selected mode. The
goal is a high level of agility and ability to accel ­
erate on curves. The vehicle is very responsive to
steering .
Cornering light*
The cornering light adapts the high beams to the
direction of the curve depending on the speed.
The pivoting action and the lighting also adapt to
the mode .
Assist
Adaptive cruise control*
The behavior when accelerating can be adjusted
from comfortable to sporty, depending on the
drive select mode. Adaptive cruise control also
responds to the driving behavior of the vehicle
ahead in a more conservative or sporty manner.
Engine sound*
The engine sound adapts to the current mode
and can be subtle to sporty.
(D Note
- Make sure there is enough clearance above
and below the vehicle when parking. The
height of the vehicle can change once it is
parked due to temperature fluctuations,
changes to the load conditions and changes
to the driving modes, which can affect clear­
ance.
- When transporting the vehicle on a car car­
rier, train, ship or by other means, only tie
the vehicle down at the running surface of
the tires, which is the outer circumference.
Securing the vehicle at the axle compo­
nents, suspension struts or towing eyes is
not permitted because the pressure in the
air suspension struts can change during
transport. The vehicle may not be secured
sufficiently if this happens.
@ Tips
- In some models, the maximum vehicle
speed can only be reached in the auto and
dynamic modes.
- The S selector lever position automatically
engages if the dynamic mode is selected.
- In vehicles that have dynamic steering*, op­
erating noise is heard when starting or stop­
ping the engine. This does not indicate a
problem.
111

Parking systems
Parking systems
General information
Applies to: vehicles with parking system plus/rearview cam­
era/peripheral camera
Depending on your vehicle's equipment , various
parking aids will help you when parking and ma­
neuvering.
The
parking system plus assists you when park­
ing by audibly and visually indicating objects de­
tected in front of and behind the vehicle
¢page 115.
The rearview camera shows the area behind the
vehicle in the Infotainment system display. This
display assists you when you are cross or parallel parking
¢ page 116. The parking system plus
functions are also available
¢ page 115.
The peripheral cameras give various views to
help you when parking or maneuvering
¢ page 119. The parking system plus functions
are also available
¢page 115.
& WARNING
-Always look for traffic and check the area
around your vehicle by looking at it directly
as well. The parking system cannot replace
the driver's attention. The driver is always
responsible when entering or leaving a park­
ing space and during similar maneuvers .
- Please note that some surfaces , such as
clothing, are not detected by the system .
- Sensors and cameras have blind spots in
which people and objects cannot be detect­
ed . Be especially cautious of small children
and animals .
- The sensors can be displaced by impacts or
damage to the radiator gr ille, bumper,
wheel housing and the underbody . The park­
ing system may be impaired as a result.
Have an authorized Audi dealer or author­
ized Audi Service Facility check their func­
tion .
- Make sure the sensors are not obstructed by
stickers, deposits or other materials. If they
are, the sensor function could be impaired.
For additional information on cleaning, see
c:> page 306.
114
(D Note
-Some objects are not detected or displayed
by the system under certain circumstances:
- Objects such as barrier chains, trailer draw
bars, vertical poles or fences
- Objects above the sensors such as wall ex ­
tensions
- Objects with certain surfaces or structures
such as chain link fences or powder snow
- If you continue driving closer to a low ob­
ject, it may disappear from the sensor range. Note that you will no longer be
warned about th is obstacle.
(D Tips
- The system may provide a warning even
though there are no obstacles in the cover­
age area in some situations, such as:
- certain road surfaces or when there is tall
grass.
- external ultrasonic sources such as from cleaning vehicles .
- in heavy rain, snow, or thick vehicle ex­
haust.
- We recommend that you practice parking in
a traffic -free location or parking lot to be­
come familiar with the system . When doing
this, there should be good light and weath­
er conditions.
- You can change the volume and pitch of the
signals as well as the display¢
page 124.
-Please refer to the instructions for towing a
trailer located in
¢page 124.
-What appears in the infotainment display is
somewhat time-delayed.
- The sensors must be kept clean and free of
snow and ice for park aid to operate .

Intelligent Technology
To restore the balance of energy, components
that require large amounts of energy are tempo­
rarily scaled back or switched off. Heating sys­
tems in particular require a great deal of energy .
If you notice, for example, that the seat heating"
or rear window defogger is not working, then it has been temporarily reduced or switched off .
These systems are available again as soon as the
energy supply has been restored.
In addition, you may notice that the idle speed
has slightly increased. That is normal and no
cause for concern . By increasing the idling speed,
the additional requ ired energy will be generated
and the vehicle battery will be charged.
Notice about data
recorded by the Event
Data Recorder and
vehicle control modules
Event Data Recorder
This vehicle is equipped with an Event Data Re­
corder (EDR). The main purpose of an EDR is to
record, in certain crash or near crash-like situa­
tions , such as an airbag deployment o r hitting a
road obstacle, data that will assist in understand­
ing how a vehicle 's systems performed. The EDR
is designed to record data related to vehicle dy­
namics and safety systems for a short period of
time, typically 30 seconds or less. The EDR in this
vehicle is designed to record such data as :
- How various systems in your vehicle were oper­
ating;
- Whether or not the driver and passenger safety
belts were buckled/fastened;
- How far (if at all) the driver was depressing the
accelerator and/or brake pedal; and,
- How fast the vehicle was traveling.
These data can help prov ide a better understand­
ing of the circumstances in which crashes and in­
juries occur. NOTE: EDR data are recorded by your
vehicle only if a non-trivial crash situation occurs ;
no data are recorded by the EDR under normal
driving conditions and no personal data (e .g.,
name, gender, age, and crash location) are re­
corded. However, other parties, such as law en-
132
forcement, could combine the EDR data with the
type of personally identifying data routinely ac­
quired during a crash investigation.
To read data recorded by an EDR, special equ ip­
ment is required, and access to the vehicle or the
EDR is needed . In addition to the vehicle manu­
facturer, other part ies, such as law enforcement,
that have the special equipment, can read the in­
formation if they have access to the vehicle or the
EDR .
Some state laws restrict the retrieval or down­
loading of data stored by ED Rs installed in a vehi­
cle for the express purpose of retrieving data af­
ter an accident or crash event without the own ­
er 's consent .
Audi will not access the EDR and/or simi lar data
or give it to others -
- unless the vehicle owner (or lessee if the vehi ­
cle has been leased) agrees; or
- upon the official request by the police; or
- upon the order of a court of law or a govern-
ment agency; or
- for the defense of a lawsuit through the judicial
discovery process.
- Audi may also use the data for research about
veh icle operation and safety performance or
provide the data to a third party for research
purposes without identifying the specific vehi­
cle or information about the identity of its own ­
er or lessee and only after the recorded vehicle
data has been accessed.
Vehicle control modules
Your vehicle is also equipped with a number of
electronic control modules for various vehicle
systems, such as engine management, emission control, airbags, and safety belts.
These electronic control modules record data during normal vehicle operation that may be
needed by trained technicians for diagnostic and
repair purposes. The recording capability of these
modules is limited to data (no sound is record­
ed) . Only a small amount of data is actually re­
corded over a very limited period of time, or stor­
ed when a system fault is detected by a contro l
module . Some of the data stored may relate to .,._

Audi connect
- Destination setup in your MMI using your
myAudi A cco unt ¢ page 167 or online map
v iew
¢ page 171.
-Traffic inf orm ation (Sir ius ): rece ive informa ­
tion about accidents, road construction and
other incidents
¢ page 175
Audi connect services on the phone
App lies to: ve hicles w ith Audi co nnect
The fo llow ing Audi connect services are currently
ava ilable :
- Storing contacts on your computer using your
m yAudi Acco unt and loading the contacts into
the MMI directory
¢ page 153
Wi-Fi hotspot
Appl ies to: ve hicles w ith Audi co nnect
You can use the MMI as a Wi-Fi hotspot to con­
nect up to eight wireless devices to the Internet. While driving, restricted use of non-secured,
light, small wireless devices is only possible from the rear of the vehicle.
.,. Select: the (fa) button > Setting s control but-
ton
> W i-Fi setting s.
The follow ing settings can be modified in the Wi­
Fi setting s
menu:
Wi-Fi acti ve
The MMI Wi -Fi hotspot is deactivated at the fac­
tory. Your Wi-Fi hotspot must be activated and
visible to establish a connection between your ve­ h icle and your wireless device.
- Off : the MMI Wi-Fi hotspot is deactivated. An
Internet connection is not possib le.
- Vis ible : the MMI Wi-Fi hotspot is active and can
be used to connect to the Internet.
- In visi ble: the MMI Wi -Fi hotspot is active but
not visible to other devices. A connection can­
not be established with a new w ireless device.
The Wi -Fi connection between your vehicle and
your wireless device ( laptop, cell phone) is en ­
crypted . To establish a connection, you must en­
ter the following settings when setting up your
wire less device. You can change them if necessa­
ry.
1 6 0 -
Netwo rk ID (SSID ):
name o f the Wi -Fi net ­
work .
-Enc ryption t ype : WEP, WPA or WPA2
- Pa ssword : depending on the encryp tion type, a
passwo rd may be generated in the MMI that is
used to encrypt the wireless connection. The
password can be changed . Be sure to se lect a
secure password. For the WEP encrypt ion type,
the password must be exactly 13 characters.
For the WPA or the WPA2 encrypt ion types, the
password must be at least
8 (maximum of 63)
characters .
-Apply sett ings : the modified settings are ap­
plied to the MMI. You must then update the
changes in your mob ile w ireless device .
A WARNING
-As the d river, do not allow usage of the Wi­
Fi hotspot to distract yo u from driv ing , as
this could increase the r isk of an accide nt.
- It is o nly safe to use laptops and similar mo­
bi le devices when the veh icle is stationary
because, like a ll loose objects, they cou ld be
thrown around the inside of the vehicle in a
crash and cause serious injuries . Store these
types of devices securely while driving.
- Do not use any wire less devices on the front
seats within range of the airbags while dr iv­
ing. Also read the warnings in the chapter
¢page 207.
(D Note
-Under some conditions, certain mobile devi­
ces and ope rating systems may automati­
cally sw itch from your vehicle's Wi-Fi hot­
spot to the device's mobile data connection.
I n that event, standard text and data usage
rates would apply while the device's mobile
data connection is in use. Please refer to
doc umentation provided by your mobile de­
vice's manufacture and your data car rier for
d etails, related te rms and pr iva cy sta te­
ment .
- Yo u ar e responsib le for all precautions ta k­
en for data pro te ct ion, anti-virus protection
and protection against loss of data on mo ­
bile devices that are used to access the In-
ternet through the Wi-Fi hotspot. ..,.