Lights AUDI Q2 2021 Owner´s Manual

Lights and vision
A WARNING
Convex or wide-angle* exterior mirrors give a
larger field of
vision.
However, they make ob­
jects look smaller and further away than they
really are. If
you
use these mirrors to
esti­

mate the distance to vehicles behind you
when changing Lane, you could misjudge the
distance. Risk of accident!
CAUTION
- Applies to vehicles with electrically retracta­
ble exterior mirrors: If one of the mirror
housings is knocked out of position (e.g.
when parking), the mirrors must be fully re­
tracted with the electric control. You will
hear
a
loud noise when the mirrors snap
back into place. Do not readjust the mirror
housing by hand, as this will interfere with
the mirror adjuster function.
- Applies to vehicles without electrically re­
tractable exterior mirrors: If one of the mir­
ror housings is knocked out of position (e.g.
when parking), it must be returned to its
proper position by hand.
- Before washing the vehicle in an automatic
car wash, please make sure to retract the
exterior mirrors to prevent them from being

damaged.
Electrically retractable exterior
mirrors* must NOT be folded in or out by

hand.
Always use the electrical power
con­

trol.

©
If the electrical adjustment should fail to op­

erate,
both of the mirrors can be adjusted by
hand by Lightly pressing the edge of the mir­
ror glass.
Anti-dazzle setting
Your vehicle is equipped with a manual or auto­
matic* anti-dazzle interior
mirror.

Manual anti-dazzle interior mirror
•
Pull
the lever
at
the bottom of the mirror to­
wards you.
Automatic anti-dazzle mirrors*
• The interior and exterior mirrors will darken
when bright light (e.g. from the headlights of
a

following vehicle) shines on the surface of the
interior mirror.

A
WARNING
Applies to: vehicles with automatic anti-dazzle mirrors
Electrolyte fluid can leak from a broken mir­
ror. This fluid can cause irritation to the
skin,

eyes,
and respiratory organs. Wash thorough­
ly with clean water should you come into
con­

tact with this
fluid.
Seek medical assistance if

needed.

© CAUTION
Applies to: vehicles with automatic anti-dazzle mirrors
Electrolyte fluid can
leak
from a broken mir­
ror. This fluid can damage plastic surfaces.
Use a wet sponge or similar to remove the
flu­

id as soon as possible.

(T) Note

Applies to: vehicles with automatic anti-dazzle mirrors
-The automatic anti-dazzle mirrors may not
function as intended if the light falling on
the surface of the interior mirror is obstruc­

ted.

-The automatic anti-dazzle mirrors do not
darken if the interior lighting is on
or
the car
is in reverse gear.
Sun visors

Fig.
44 Left side: Sun visor (example)
The sun visor can be pulled out of its mounting
and turned towards the
door
(T).
•
54

Lights and vision

CO

<
o
rN
iv
rN
t-H
o
< 00
The light* for the make-up mirror comes on auto­
matically when you slide open the mirror cover
©•
Windscreen wipers
Switching on the windscreen wipers

V

WJIO
*

Fig. 45
Windscreen
wiper
lever

m®

v
"trj-i

s
to
o > 03 m

Fig.
46 Control lever for rear wiper
Move the windscreen wiper lever to the appropri­
ate position:

@-Wipers
off
(Î) - Intermittent wipe. Move switch
®
to the Left
or to the right to increase or reduce the wiper de­
lay interval. If your vehicle is equipped with a rain
sensor*, the windscreen wipers will be activated
automatically in the rain as long as the vehicle
has been moving faster than approx. 4 km/h at
Least once. The higher the sensitivity level for the
rain sensor (i.e. the further switch
(Â)
is moved to
the right), the sooner the windscreen wipers re­
act to moisture on the windscreen. You can deac­
tivate the rain sensor mode on the infotainment
system (this will activate the intermittent wipe
mode). To do so, select: |MENU| button > Car >
left control button > Driver assist
>
Rain sensor.

@-
Slow wipe

(|)-
Fast
wipe
(?) - Single wipe. If
you
hold the lever in this
posi­

tion,
the wipers will switch from slow continuous
wiping to fast continuous wiping after
a
while.
(D - Wash/wipe. The screen is given an extra wipe
a few seconds later to remove any dribbles of wa­
ter (if the vehicle is moving and the temperature
is above approx. 4
°C).
You can deactivate this
function by moving the lever to position
(s)
again
within 10 seconds after the extra wipe. The ex­
tra-wipe function is activated again the next time
you switch on the ignition.
Headlight washers*. The headlight washer sys­

tem*
only operates when the dipped headlights
are switched on. The headlights are also auto­
matically washed intermittently when you move
the lever to position
(s).

(?) - Rear wipe. The rear window is wiped approxi­
mately every 6 seconds.
If the windscreen wipers are on and in operation,
the rear window wiper will also be switched on
automatically when you engage reverse gear.

©-
Rear wash/wipe. The number of wiper cycles
depends on how long you hold the Lever in
posi­

tion©.
A WARNING
- The rain sensor* is only intended to assist
the driver. The driver is still obliged to
man­

ually operate the windscreen wipers as re­
quired depending on visibility.
- Do not use water-repellent coatings on the
windscreen. In bad visibility conditions such
as light
rain,
low sun or when driving at
night these coatings can cause increased
dazzle, which is a serious safety hazard.
Such coatings can aLso cause the wiper
blades to judder.
- Poor visibility can cause accidents. Always
ensure that the wiper blades are in good
condition
^>page
56, Changing the
wind­

screen wiper blades.
55

Lights and vision
© CAUTIO © CAUTION
- In icy conditions, check that the wiper
blades are not frozen to the windscreen. If
the wiper blades are frozen to the
wind­

screen when you switch on the windscreen
wipers, this could damage the wiper blades.
- Make sure you switch off the windscreen
wiper system (lever in position
@)
before
you use an automatic car wash. This will
avoid inadvertent triggering of the wipers
and possible damage to the wiper system.
© Note
- The windscreen wipers are deactivated
when the ignition is switched off. You can
activate the windscreen wipers after switch­
ing the ignition on again by moving the
windscreen wiper lever to any position.
- Worn or dirty wiper blades can cause smear­
ing on the glass. This can also impair the ef­
fectiveness of the rain sensor. Please check
the wiper blades regularly.
-The windscreen washer jets are heated*
when the ignition is switched on if the out­
side temperature is low.
- If
you
stop briefly, e.g. at traffic lights, the
wiper speed setting will automatically be re­
duced
by
one level.
Cleaning the wiper blades
Clean the wiper blades if the wipers leave smear­
ing on the glass. Use a soft cloth and glass clean­
ing solution.
Windscreen wipers
• Set the wiper arms to the service position

^>page
56.
• Lift the wiper arms away from the glass.
Rear window wiper
• Lift the rear wiper arm away from the glass.

/\
WARNING
Dirty wiper blades can impair the driver's view
- risk of accident!
If the wipers still Leave smearing on the glass
after they have been cleaned, the wiper
blades should be replaced
<=>page
56.
Changing the windscreen wiper blades

Fig.
47 Removing the wiper blades
Service position / wiper change position
• To move the windscreen wipers into the service

position,
switch off the ignition and move the
windscreen wiper lever to position (3) for at
least 2 seconds
<^page
55, Fig. 45.
• To move the windscreen wipers back to their
original position, switch on the ignition and
move the windscreen wiper lever to position (4)
for at least 2 seconds.
Taking off the wiper blade
• Lift the wiper arm away from the glass.
• Press the release button
(T)
on the wiper blade

^>Fig.
47. Keep hold of the wiper blade while
doing so.
• Take off the wiper blade in the direction of the
arrow.
Fitting the wiper blade
• Fit the new wiper blade into the mounting on
the wiper arm (5). You should hear it engage in
the wiper arm.
• Fold the wiper arm back down onto the
wind­

screen.

• Switch off the service position again.

A
WARNING
For safety, the wiper blades should be
changed once or twice a year.
56

Lights and vision
© CAUTION
- The wipers must be in the service position
before lifting them off the windscreen!
Oth­

erwise the wiper motor or the paintwork on
the bonnet may be damaged.
- Never drive your vehicle or operate the
windscreen wiper Lever while the wiper arms
are off the glass in a raised position. The
wipers will otherwise automatically return
to their park position and may damage the
bonnet and windscreen.
© Note
- You can also use the service position, for ex­

ample,
if
you
want to fix
a
cover over the
windscreen in the winter to keep it clear of

ice.

- You cannot activate the service position
when the bonnet is open.

A
WARNING
For safety, the wiper blades should be
changed once or twice a year.
Changing the rear wiper blade

CO
<
O
rN
iv
rN
•-i

00

Fig.
48 Rear window wiper: Removing the wiper blade
Taking off the wiper blade
• Lift the rear wiper arm away from the glass.
• Take hold of the wiper blade below the centre
and
pull
the blade out of the retainer in the di­
rection of the -arrow-
^Fig.
48. Keep hold of
the wiper arm while doing so.
Fitting the wiper blade
• Press the mounting on the wiper blade into the
retainer. While doing so, keep holding the plas­
tic top end of the wiper arm.
• Fold the wiper arm back down onto the rear
window.
57

Heating and cooling
Heating/ventilation system or manual air conditioner
Applies to: vehicles with heating/ventilation system or manual air conditioner

Fig.
65 Heating/ventilation system or manual air conditioner*: Controls

CO

<
O
rN
IV
rN
•-i

00
The functions can be switched on and off using
the buttons and controlled using the rotary
con­

trols.
The LED in the corresponding button lights
up when the function is switched on.
Manual air conditioner*
For
a
comfortable climate inside the vehicle us­
ing the air conditioner:
- In the summer, adjust the temperature to just
a few degrees below the outside temperature
- Do not turn the blower up too high
- Do not point the air outlets directly at the occu­
pants
A/C Cooling mode*
The air cooling system only works when the blow­
er is switched on. The air cooling mode is switch­
ed on/off when the A/C button is pressed. When
the air cooling is switched off, the air is not
cooled and therefore not dehumidified. The
win­

dows may mist up as a result. The air cooling is
switched off automatically at low outside
tem­

peratures.

#
/ # Temperature
Rotary control ® is used to adjust the tempera­

ture.

%
Blower
You can adjust the blower speed manually using

control®.
You should leave the blower on at a
low setting to prevent the windows from misting
up and to ensure that the vehicle interior is
con­

stantly ventilated. To demist the windows, we
recommend
that
you increase the blower speed
and set control ® to

W/
v?/
*JI
*J Air distribution and air
outlets
The rotary control ® can be used to adjust the
air distribution. A setting between
f£j
and
*J

usually provides a comfortable environment.
At the
^
setting, the windscreen and side
win­

dows are defrosted or demisted as quickly as pos­

sible.
The air recirculation is switched off, but can
be switched on again manually by pressing the

button.
The round air outlets in the dashboard can be ad­
justed
^page
71.
To prevent the front side windows from misting
up in wet weather, it's a good idea to open the
side air outlets and point them to the side.
Foot-level air outlets are provided underneath
the front seats to heat the rear cabin.
67

Heating and cooling
Automatic air conditioner
Applies to: vehicles with automatic air conditioner

We
recommend pressing the AUTO button and setting the temperature to 22 °C (72 °F).

Fig.
66 Automatic air conditioner: Controls (example)

CO

<
O
rN
IV
rN
t-H
o <
The functions can be switched on and off using
the buttons and controlled using the rotary
con­

trols.
The LED in the corresponding button lights
up when the function is switched on.
Automatic air conditioner
The air conditioner is fully automatic, and will
maintain the desired temperature at a constant

level.
When the heater is on, the blower normally
only switches to a higher speed once the coolant
has warmed up sufficiently (this does not apply
to the defrost setting).
AUTO Automatic or "eco" mode*
The automatic mode maintains a constant
tem­

perature inside the vehicle. Air temperature, out­
put and distribution are regulated automatically.
The AUTO mode is switched off immediately
when you operate any of the manual air controls.
The "eco"
mode*1*
is activated if you press the
AUTO button briefly while automatic mode is ac­

tive.
Fuel is saved in "eco" mode* because the
settings respond more passively. The "eco"

mode*
is on when eco appears in the console dis­
play. The "eco" mode* is deactivated when you
press the AUTO button again.

1J
This function is not available on all export versions.
A/C Cooling mode
The air cooling system only works when the blow­
er is switched on. The air cooling mode is switch­
ed on/off when the A/C button is pressed. When
the air cooling is switched off, the air is not
cooled and therefore not dehumidified. The
win­

dows may mist up as a result. The air cooling is
switched off automatically at low outside
tem­

peratures.

#
/ # Temperature
The temperature for the driver's and front pas­
senger's sides can be set separately using
con­

trols ® and @. The temperature can be adjusted
between +16 °C (+60 °F) and +28 °C (+84 °F).
Outside this range, LO or HI will appear on the air
conditioner display. In the two extreme settings
the air conditioner operates continuously with
maximum cooling or heating output, and the
temperature is not regulated automatically.
Synchronisation: By pressing the AUTO button
for 2 seconds, the temperature of the passeng­
er's side can be set to the temperature of the
driver's side. The settings remain synchronised
until the temperature is changed on the passeng­
er's side.
I

69

Driving
instance when you can see that the next traffic
lights are red. This takes advantage of the engine
braking effect, reducing wear on the brakes and

tyres.
Emissions and fuel consumption will drop
to zero due to the overrun fuel cut-off.
Change gear early to save fuel
An effective way of saving fuel is to change up
quickly through the gears. Running the engine at
high rpm in the lower gears uses an unnecessary
amount of
fuel.

Applies to: vehicles with manual gearbox
Shift up to second gear as soon as possible. If
possible, we recommend shifting up to the next
gear at approx. 2,000 rpm.
Applies to: vehicles with automatic gearbox
Press the accelerator slowly and avoid using the

"kick-down"
feature.
Avoid driving at high speed
Avoid travelling at top speed. Fuel consumption,
exhaust emissions and noise Levels all increase
very rapidly at higher speeds. Driving at moder­
ate speeds will help to save
fuel.

Do not let the engine idle for longer than
necessary
Engine idling periods are automatically reduced
on vehicles with start/stop system*. On vehicles
without a start/stop system, it is worthwhile
switching off the engine at level crossings, for in­
stance, or at traffic lights with a long red phase.
The fuel saved after about 5 seconds can be
greater than the amount of fuel needed to re­
start a warm engine (the exact fuel saving de­
pends on the engine version).
The engine takes a very long time to warm up
when it is running at idling speed. Mechanical
wear and pollutant emissions are also especially
high during this initial warm-up phase. It is
therefore best to drive off immediately after
starting the engine. Avoid running the engine at
high speed.

o
Regular servicing
Regular servicing can establish a basis for good

iS
fuel economy before you start driving. A
well-

serviced engine gives you the benefit of im­
proved fuel efficiency as well as maximum relia­
bility and an enhanced resale value. A poorly
maintained engine can consume up to ten per­
cent more fuel than necessary.
Avoid short trips
The engine and emission control system need to
reach their proper working temperature in order
to minimise fuel consumption and emissions.
A cold engine uses disproportionately more
fuel.

The engine only reaches its working temperature
after about four kilometres, when fuel consump­
tion will return to a normal level.
Check tyre pressures
Always make sure the tyres are inflated to the
correct pressures
•=>page
306 to save
fuel.
If the
tyre pressures
are
just 0.5
bar
too Low, this can
increase the fuel consumption by as much as 5
%. Due to the greater rolling resistance, under-
inflation also increases tyre wear and impairs

handling.

Do not use winter tyres all through the year; they
will increase fuel consumption by up to 10 %.
Avoid carrying unnecessary loads
Every kilo of extra weight will increase the fuel
consumption, so it is worth checking the Luggage
compartment occasionally to make sure that no
unnecessary loads are being transported.
The roof carrier increases the air resistance of the
vehicle and should be removed when not in use.
This will save about 12 % of fuel at speeds of be­
tween 60 and 75
mph.

Save electrical energy
The engine drives the alternator to generate elec­
tricity. This means that fuel consumption rises
when more power is required for electrical equip­
ment. Switch off electrical equipment when it is
not needed. Electrical equipment which uses a
lot of electricity includes the blower (at a high
setting), the rear window heating and the seat

heating*.

73

Driving
Steering
Adjusting the steering wheel position
The height and reach of the steering wheel can
be adjusted as required to suit the
driver.

Fig.
68 Steering column: Lever for steering column adjust­
ment

•
Push the Lever
^>Fig.
68 down
<=> /\.
•
Move the steering wheel to the desired
posi­

tion.

•
Then push the lever towards the steering
col­

umn until the catch engages.
WARNING
- Never adjust the position of the steering
wheel when the vehicle is moving - this
could cause an accident.
- Press the lever upwards so it is secure and
so that the position of the steering wheel
cannot shift unexpectedly while the vehicle
is moving - risk of accident!
Starting and stopping
the engine (vehicles with
ignition Lock)
Starting the engine
Applies to: vehicles with ignition lock
Insert the key in the ignition lock to switch on
the ignition and start the engine.

Fig.
69 Ignition lock: Ignition key positions
Switching the ignition on/off

•
To switch on the ignition, turn the ignition key
to position ®. Vehicles without start/stop sys­

tem*:
The rev counter needle will move to the
READY position.
• To switch off the ignition, turn the ignition key
to position ©. The rev counter needle will
move to the OFF position.
Diesel engines are automatically preheated when
you switch on the ignition.
Starting the engine

•
Manual gearbox: Press the clutch pedal all the
way down and move the gear lever into neutral.

•
Automatic gearbox: Press the brake pedal and
move the selector lever to position P or N.

•
Turn the ignition key briefly to position @. The
ignition key automatically returns to position
®. Do not press the accelerator.
Applies to: vehicles with diesel engine

•
The engine may take a few seconds Longer than
usual to start on cold days. Please keep your
foot on the clutch pedal (manual gearbox) or
brake pedal (automatic gearbox) until the en­
gine starts. The indicator Lamp
E g
lights up
while the glow plugs are preheating.
74

Driving
©
y
Note
After the engine is stopped, the radiator fan
may remain on or turn itself back on for up to
10 minutes, even if the ignition is switched
off. This may occur for the following reasons:
- Residual heat has raised the coolant
tem­

perature.
- Direct sunlight has additionally heated up
the engine compartment while the engine is

warm.

- Applies to vehicles with diesel particulate
filter: The emission control system is hot
because of the regeneration process, even
though the engine has
not
yet reached oper­
ating temperature.
Starting and stopping
the engine (vehicles with
convenience key)
Starting the engine
Applies to: vehicles with convenience key
You can use the ISTART ENGINE STOP| button to
switch on the ignition and start the engine.

Fig.
70 Centre console: START ENGINE STOP button
Starting the engine

•
Manual gearbox: Press the clutch pedal all the
way down and move the gear lever into neutral.

•
Automatic gearbox: Press the brake pedal and
move the selector lever to position P or N.

•
Press the ISTART ENGINE
STOP!
button briefly
to start the engine.
Applies to: vehicles with diesel engine

•
The engine may take a few seconds longer than
usual to start on cold days. Please keep your
foot on the clutch pedal (manual gearbox) or
brake pedal (automatic gearbox) until the en­
gine starts. The indicator Lamp
E 3
lights up
while the glow plugs are preheating.
Electrical components with a high power
con­

sumption are switched off temporarily while you
start the engine.
If the engine fails to start immediately, switch
off the starter by pressing the
ISTART
ENGINE
STOPI
button once more and try
again after about 30 seconds.
Switching the ignition on/off
If you only wish to switch on the ignition and do
not want to start the engine as
well,
proceed as
follows:

•
Press the ISTART ENGINE STOP| button with­
out pressing the clutch (manual gearbox) or
brake pedal (automatic gearbox). Vehicles
without start/stop system*: The rev counter
needle will move to the READY position.

•
To switch off the ignition, press the button

again.
The rev counter needle will move to the
OFF position.
Diesel engines are automatically preheated when
you switch on the ignition.
If the indicator lamp
£21
flashes and the message
Please move steering wheel appears when you
switch on the ignition, the steering wheel is

locked.
In this case, turn the steering wheel
slightly
to
the left/right.
Start/stop system*
Please note the information on
<^>page
79,
Start/stop system.
WARNING
Never run the engine in confined spaces. The
exhaust gases are toxic - risk of poisoning!
© CAUTION
Avoid high engine speeds, full throttle and ex­
treme load conditions until the engine has
reached its normal operating temperature;
otherwise this can damage the engine. •
76

Driving
This message appears
and a
buzzer sounds
if
you
open
the
driver's door while
the
engine
is
run­

ning.

Pressing start/stop button again will switch
off

engine.
This message appears
if
you press
the

ISTART
ENGINE
STOPI*
button while
the
vehicle
is moving
<^>page
77,
Emergency
Off
function.
Engine start system: fault. Please contact work­
shop
A fault
has
occurred when starting
the
engine
au­

tomatically (automatic start function). Drive
to a

qualified workshop soon
and
have
the
fault
recti­

fied.
To
start
the
engine, turn
the
ignition
key to

position
@
^>page
74 or
press

the
ISTART
ENGINE
STOPl
button and hold the

key/button until
the
engine starts.

D
Key not
recognised. See owner's manual
This message appears
if
there
is no
convenience
key inside
the
vehicle
or if
the system cannot
de­

tect
or
identify
the
key. This
can
happen,
for ex­

ample,
if
the radio signal from
the key is
obstruc­
ted
by a
metal briefcase
or
similar,
or if the key

battery
is
weak. Electronic equipment, such
as

mobile phones,
can
also interfere with
the
radio
signal from
the key.

The engine
can
still
be
started
or
stopped
if
this
happens (please refer
to
^page
79).

C]
Remote control key: hold back
of key

against marked area.
See
owner's manual
If
the
indicator lamp lights
up and the
message
appears,
a
malfunction
has
occurred

^>page
79.

3
Key not in
vehicle?

3
Remote control key:
key not
recognised.
Is

key still
in
vehicle?
If
the
indicator
lampGB
Lights
up and the
mes­
sage appears,
the
convenience
key
was removed
from
the
vehicle while
the
engine
was
running.
If

the convenience
key is not in the
vehicle
you
will
not
be
able
to
switch
on the
ignition
or
restart
the engine after
it has
been switched
off. You
will
also
not be
able
to
lock
the
vehicle from
the
out­

side.

Please press brake pedal
This message appears
on
vehicles with
an
auto­
matic gearbox
if
you
try to
start
the
engine
with­

out first pressing
the
brake pedal.
Please press clutch pedal
This message appears
if
you
try to
start
the en­

gine without first pressing
the
clutch pedal.
The

engine will only start
if
you press
the
clutch
ped­

al.

Please engage
N or P

This message will appear
if
you
try to
start
or

switch
off the
engine when
the
selector lever
is

not
in N or P. The
engine
can
then
not be
started
or switched
off.

Switch
off
ignition before leaving
car.
Battery
is

being discharged
This message appears
and the
buzzer sounds
if

you open
the
driver's door while
the
ignition
is

switched
on.
Switch
off
the ignition
to
prevent
the vehicle battery from being discharged.
Shift
to P,
vehicle can roll away. Doors can only
be locked
in P

For safety reasons, this message will appear
if

the selector Lever
of the
automatic gearbox
is not

in position P when
you
switch
off the
ignition.
Put

the selector lever
in
position
P;
otherwise
the ve­

hicle
can
roll away
and
cannot
be
locked.
78