high beam AUDI Q2 2021 Owner´s Manual

Instruments and controls

CO

s
rN rN

•-i

00
Fuel has entered the engine oil due to low out­
side temperatures or frequent short trips. Drive
until the engine is warm to allow the fuel to
evaporate out of the engine oil. When doing so,
avoid high engine speeds, full acceleration and
heavy engine loads.

m
Fuel tank system
P3 Please refuel
When the indicator lamp lights up for the first
time and the message appears, there are still
about 7 litres (front-wheeL drive) or about
8.5
li­
tres (four-wheel drive) of fuel left in the tank.

IM
Please refuel immediately
If the indicator lamp lights up and the message
appears, the fuel tank is almost empty. Drive to a
filling station without delay.

E3
Tank system malfunction! Please contact
workshop
There is a malfunction in the tank system.
Drive to a qualified workshop without delay and
have the fault rectified.

S
Driver's door*
For more information about filling the tank,
refer to
=>page
290.

Washer fluid level
Please add washer fluid
With the ignition switched off, top up the fluid
for the windscreen washer and headlight washer

system*
^>page
303.

!
Windscreen wipers
Windscreen wiper defective
There is a malfunction in the windscreen wipers.
Drive to a qualified workshop without delay and
have the fault rectified.

E]
Driver's door: fault. Shift to P before leaving
vehicle. See owner's manual
A malfunction has occurred in the driver's door.
Move the selector lever to position P (automatic
gearbox) to hold the vehicle.
Drive to a qualified workshop soon and have the
fault rectified.

- Bulb monitor
If the indicator Lamp
jjjj
Lights up, a bulb has

failed.
The message indicates the location of the

bulb.

Have the bulb replaced without delay.
Vehicle lights: malfunction!
There is a fault with the headlights or light

switch.
Drive to a qualified workshop soon and
have the fault rectified.

/\
WARNING
Bulbs are sensitive to pressure. The glass can
break when you touch the bulb, causing in­
jury.

ip
Dynamic headlight range control
Applies to: vehicles with dynamic headlight range control

13
Headlight range control: system fault!
There is a malfunction in the dynamic headlight
range control which may cause other road users
to be dazzled.
Drive to a qualified workshop without delay and
have the fault rectified.

•D
Audi adaptive light
Applies to: vehicles with Audi adaptive light

US
Audi adaptive light: system fault!
There is a malfunction in the adaptive light. The
dipped beam headlights will still be working nor­
mally.
Drive to a qualified workshop soon and have the
fault rectified.
35

Lights and vision

CO

<
O
rN rN

•-i

00
• Press the lever forwards (3)
^>page
50,
Fig. 38
to activate the main beam assist. The indicator
lamp
^/fi8
will light up in the instrument
cluster display and the main beams will be
switched on/off automatically. An indicator

lampBS
lights up when the main beams are
switched on.
Switching the main beams on/off manually
If the main beams are not switched on or if the
headlights are not dipped as expected, you can
control the dip function manually:
• To switch on the main beams manually, push
the lever forwards
(3).
The indicator Lamp
g

will
Light
up. To dip the headlights again, pull
the lever towards you 0.
• To dip the headlights manually, pull the lever
towards you
@.
The main beam assist will be
deactivated.
Flashing the headlights
• Pull the lever towards you
@
to flash the
head­

lights when the main beam assist is activated
and the main beams are dipped. The main
beam assist will remain activated.
Driver messages in the instrument cluster
display

13
Main beam assist: system fault!

1H
Main beam assist: fault. See owner's manual
Drive to a qualified workshop soon and have the
fault rectified. You can still switch the main
beam headlights on and off manually.

13
Main beam assist: currently unavailable. No
camera view

HI
Main beam assist: currently unavailable.
Camera view restricted due to surroundings.
See owner's manual
The camera vision is impaired, e.g. by stickers or
dirt. Please clean the windscreen.
The sensor is located in the mounting for the in­
terior mirror. Do not affix any stickers on this sec­
tion of the windscreen.
A WARNING
The main beam assist is only intended to as­
sist the driver. The driver must always ensure
that the headlights are used when required,
and may have to switch them on or off
man­

ually, e.g. when the Light conditions or visibili­
ty are poor. In the following situations
man­

ual intervention may be necessary:
- Hazardous weather conditions such as fog,
heavy rain and snow or water splashes
- Roads on which oncoming traffic is partially
concealed (e.g. on motorways)
- Indiscernible road users (e.g. cyclists with
poor lighting)
- Tight corners, steep hill crests or valleys
- Poorly lit towns
- Highly reflective objects, such as road signs
-Windscreen misted up, dirty, frosted or cov­
ered by stickers in front of the sensor
Adjusting the settings for the exterior
lighting

You
can change the settings for these functions
on the infotainment system.
• Select the following on the infotainment sys­

tem:
IMENUI
button > Car
>
left control button
> Vehicle settings > Exterior lighting.
Automatic headlights*
The following settings are available in the Auto­
matic headlights menu:
Activation time* - You can determine how soon
the lights are switched on by using the settings
early*, medium* or late* to adjust the sensitivity
of the light sensor.
Main beam assist* - You can switch the main
beam assist* on/off.
Entry/exit
lights*

You can switch the entry/exit lights* on and off.
They illuminate the area around the vehicle after
dark when you unlock the vehicle or when the ig­
nition has been switched off and the driver's door

opened.
•
51

Driving
- The power consumption is
high.

The engine switches off again when the condi­
tions for start/stop mode are once again
fulfil­

led1).

Ignition is switched off automatically
To prevent the vehicle battery from being dis­

charged,
the ignition will be switched off auto­
matically if certain conditions are met. For in­
stance:
- The start/stop system has switched off the en­

gine.

- The vehicle is stationary.
- The driver has left the vehicle.
If the dipped beam headlights are switched on in
this case, the side lights will be turned on in­

stead.
After approx. 30 minutes, or when you
lock the vehicle, the side Lights will be switched

off.

If the start/stop system has not stopped the en­
gine or if
you
have switched off the start/stop
system manually, the engine will continue
run­

ning and the ignition will not be switched off au­
tomatically
^A-

A WARNING
Never run the engine in confined spaces. The
exhaust gases are toxic - risk of poisoning!
© Note
If
you
select
D
or
N
after selecting reverse
gear on a vehicle with automatic gearbox, the
car must have been moving at over 10 km/h
before the system can switch off the engine

again.

Switching the start/stop system on/off
manually
Applies to: vehicles with start/stop system

You
can switch the system off manually if you
don't want to use it.
_.

rA^OFF

un
S
o
>
CO CO

Fig.
73 Centre console: Switch for start/stop system

•
To switch the start/stop system off or on
man­

ually, press the
\OE1
button. The LED in the but­
ton will light up when the system is switched

off.

© Note
If
you
switch off the system during a stop

phase,
the engine will start again automati­
cally.
Driver messages in the instrument cluster
display
Applies to: vehicles with start/stop system

H
Automatic
start/stop
deactivated: Please re­
start engine manually
This message appears if certain conditions have
not been met during the stop phase and the
start/stop system cannot start the engine again
automatically. In this case, the engine must be
started manually.

2]
Automatic
start/stop:
system fault! Func­
tion unavailable
There is a malfunction in the start/stop system.
Drive to a workshop soon and have the fault
recti­

fied.

CO

rN
IV
rN
t-H
o <
1)
May vary in different countries
81

Towing a trailer
Tyre pressure
Check the tyre pressures on your car, and adjust
for "full
load"
conditions (refer to the sticker list­
ing the tyre pressures)
^>page
307. It may also
be necessary to adjust the tyre pressures on the
trailer according to the recommendations of the
trailer manufacturer.
Exterior mirrors
Check whether you can see enough of the road
behind the trailer with the standard mirrors. If
this is not the case you should have additional
mirrors fitted. Both exterior mirrors should be
mounted on hinged extension brackets. Adjust
the mirrors to give sufficient vision to the rear.
Headlights
Before starting
a
journey, check the headlight
beam settings with the trailer hitched up. Adjust
the headlight settings if necessary.
On vehicles with halogen headlights, the
head­

light range control must be adjusted, see

tapage
49.
The headlight range control will be adjusted au­
tomatically if your vehicle is equipped with LED
headlights*.
Power supply
To ensure that the engine can be started again
after the ignition is switched off, the power
man­

agement system
^>page
149 controls the distri­
bution of electrical power and gradually switches
off unnecessary electrical equipment. The trailer
is supplied with power during this period. The
power supply to the trailer is interrupted while
the engine is being started.
Removable ball joint coupling
Vehicles with a factory-fitted towing bracket are
equipped with a removable
ball
joint coupling.
This is stored in the spare wheel well or in a sepa­
rate bag on the floor of the luggage compart­
ment, together with the necessary fitting instruc­

tions.

We recommend having the car serviced be­
tween the normal inspection intervals if it
used frequently for towing a trailer.
Trailer stabilisation system
Applies to: vehicles with towing bracket
Trailer stabilisation helps to reduce the risk of
the vehicle skidding when towing a
trailer.

When is the trailer stabilisation
system1'

activated?
Trailer stabilisation is active when the following
requirements are met:
- The ESC must be switched on
^>page
146 and
fully functional (no ESC malfunction).
- The trailer connector must be properly secured
in the vehicle socket.
- The vehicle speed must be higher than approx.
60 km/h.
How trailer stabilisation works
In many cases, the driver can stabilise a swaying
trailer by manually braking the vehicle.
However, if the ESC detects that the trailer is
swaying and this is affecting the towing vehicle,
it will automatically brake the vehicle in order to
stabilise the trailer. The indicator
Lamp Hi
will
flash in the instrument cluster. If possible, do
not turn the steering wheel at this stage.
In order to warn traffic behind you, the brake
lights will come on during this automatic braking

operation.

A trailer may sway quite considerably without the
trailer stabilisation system intervening.
If the system for activating the trailer brake
lights is defective, this will be indicated in the in­
strument cluster display
opage
35,
:&
Bulb

monitor.
•

CO

rN
rN
t-H
o <
x)
Not available on vehicles for some markets.
97