engine oil AUDI Q3 2017 Owner´s Manual

Checking and Filling
Engine compartment overview
The most important check points.
Fig. 140 Typical location of the rese rvoir and the engine o il fil le r open ing
(D Coolant reservoir (- L) ¢ page 166
@ Oil dipstick ¢ page 164
® Engine oil filler opening ('t:::r.) ¢page 164
© Eng ine oil label* w ith VW standard
¢page 162
® Brake fluid reservoir ((0)) ¢ page 168
® Vehicle battery(+) ¢ page 169, ¢page 209
(?) Jump start point( -) w ith hex head screw
¢page 169, ¢page 209
@ Washer fluid reservoir (O) ¢ page 169
® Fuse housing c:::> page 205
The oil dipstick (position @) and the engine oil
filler open ing (pos it ion @) can be located in dif­
fe rent positions depending on the engine ver­
sion .
_8. WARNING
Read and follow the WARNINGS befo re
checking anything in the engine compartment
162
¢ &. in Working in the engine compartment
on page 159.
Engine oil
Engine oil specifications
The engine oil used must conform to exact speci­
fications.
The serv ice interval display i n the inst rumen t
cluster o f your vehicle will inform you when it is
time for an oi l change . We recommend that you
have your o il changed by an author ized A udi Serv­
ice Adv isor.
If you must add oil between oil changes, use an oi l that matches the Aud i oi l quality standard
li sted on the sticker. The sticker is located at the
front of the eng ine compartment ¢
page 162,
fig. 140 .

00
00
......
"' ,....
"' ...... 0 0 :::,
00
A udi rec ommend s
@;Cilstrot /Jgjgf ~ f'r,w.~7dr,,'1AJ.
A ud i re commends Longlife high p erform ance
e ngi ne oil from A udi Gen uin e P art s
Using the proper engine oil is important for the
functionality and service life of the engine. Your
engine was factory-filled with a high-quality oil
which can usually be used throughout the entire
year .
Note
Your Limited New Vehicle Warranty does not
cover damage or malfunctions due to failure
to follow recommended maintenance and use
requirements as set fo rth in the Aud i Owner's
Manual a nd Warranty & Mai ntenan ce booklet.
- Use only a high quality eng ine oil that ex-
pressly complies with the Aud i oil q ual ity
standard specified for your vehicle's engine. Using any other oil can cause serious engine
damage .
- Do not mix any l ubricants or othe r addi tives
into the engine oil. Doing so can cause en­
gine damage.
(D Tips
If you need to add oil and there is none availa­
ble that meets the Audi oil quality standard
your engine requires, you may add a total of
no more than 0 .5 quart/liter of a high-quality
"synthet ic"oil that meets the following speci­
fications.
- ACEA A3 or API SM with a viscosity grade of
SAE OW-30, SAE SW-30 or SAE SW-40.
- For more information about engine oi l that
has been approved for your vehicle, please
contact e ither your authorized Audi dea ler
or Audi Customer Relat ions at
1 (800) 822-2834 or vis it our web site at
www.audiusa.com or www.aud icanada .ca.
Ch eck ing and Filling
Engine oil consumption
The engine in your vehicle depends on on ade­
quate amount of oil to lubricate and
cool oil of
its moving ports.
In order to provide effect ive lubrication and cool­
ing of internal engine components, all internal
combust ion eng ines consume a certa in amount
of oil. Oil consumption varies from eng ine to en­
gine and may change s ign ificantly over the life of
the engine. Typ ica lly, engines w ith a specified
break-in period (see
q page 58) consume more
oi l during the break -in period than they consume
after oil consumption has stabilized.
Under normal cond itions, the rate of oil con­
sumption depends on the q uality and viscosity o f
the oil, the RPM (revol utions per minute) at
which the engine is operated, the ambient tem­ perature and road condit ions. Further factors are
the amount of oil dilution from water condensa­
tion or fuel residue and the oxidation level of the o il. As any engine is subject to wear as mileage
builds up, the oil consumption may increase over
time unt il replacement of worn components may
become necessary.
With all these variables coming into play, no standard rate of o il consumption can be estab­
li shed or spec ified . T he re is no alte rnative to reg­
u la r and frequent checking of the oi l level , see
Note .
If the yellow engine o il leve l warning symbo l !I
in the instrument cluster lights up, you sho uld
check the o il level as soon as possible
q page 164. Top off the o il at your earlies t con­
venience.
A WARNING ~
Before you check anything in the engine com-
partment, always read and heed all WARN­
INGS
q .&. in Working in the engine comport­
ment on page 159.
(D Note
Driving with an insufficient oil level is likely to
cause severe damage to the eng ine. ..,.
163

Checking and Filling
@ Tips
-The oil pressure warning display. is not
an indicator of the oil level. Do not rely on
i t. Instead , check the oil level in your en­
gine at regular intervals, preferably each
time you refuel, and always before going
on a long trip.
- If you have the impression your engine con­
sumes excessive amounts of oil, we recom­
mend that you cons ult an autho rized Aud i
dealer to have the cause of your concern
properly diagnosed. Keep in mind that the
accurate measurement of oil consumption
requires great care and may take some
time. An authorized Audi dealer has instruc­
tions about how to measure oil consump­
tion accurately .
Checking the engine oil level and adding
engine oil
Fig. 141 Oil d ipst ick: check ing engine o il level
Fig. 142 Engine co mpa rtment : en gin e oi l fille r opening
cove r
Obse rve the safety p recau tions c:::> & in Working
in the engine comportment on page 159.
Checking the engine oil level
-Park the vehicle on a level surface.
164
- Shut the engine off when it is warm . Wait ap­
proximate ly two minutes so that the engine oil
can flow back into the oil pan.
- Open the hood c:::>
page 161.
-Remove the oil d ipstick c:::> page 162, fig . 140,
w ipe it off with a clean cloth and inse rt it all the
way in again.
- Remove the oil dipstick again and then read the
oil level c:::>
table on page 164.
-Add engine o il if necessary.
Area on oil dipstick
c:::> fig. 141.
@ If
the engine oil leve l is just before the
mark ing@ , then engine oil must be added.
See
c:::> (D.
@ Do not add engine o
il.
Adding engine oil
- Unscrew the cap "t!:;f; c:::> fig. 142 for the engine
oil f illing opening c:::>
page 162, fig . 140.
- Carefully add 0.5 quart (0.5 liter) of the correct
oil c:::>
page 162.
-Check the oil level again after two minutes.
- Add a smaller amount of engine oil if necessa-
ry . The mark ing@c:::>fig .
141 must not be ex­
ceeded c:::>
(D.
-Sc rew the engine oil filler cap "t!:;f; and slide the
dipstick all the way in.
A WARNING
- When adding engine oil, do not let oil drip
onto hot engine components. This increases
the risk of a fire.
- You must seal the cap on the oil filler open­
ing correctly so that oil does not leak out
onto the hot engine and exhaust system
when the engine is running, because this is
a fire hazard.
-A lways clean sk in thoroughly if it comes into
contact with engine oil.
(D Note
-The engine oil level must not be under the
marking @, because this increases the risk
of engine damage .
- After adding engine oil, the oil leve l must
not be above the mark ing@ , because this

00
00
......
"' ,....
"' ...... 0 0 :::,
00
increases the risk of catalytic converter and/
or engine damage. Do not start the engine. Contact an authorized Audi dealer or au­
thorized Audi Service Facility to have excess
engine oil extracted if necessary.
- Do not mix any additional lubricants into
the engine o il. Damage caused by such addi­
tives is not covered by the warranty.
@ For the sake of the environment
-Engine o il should never enter the sewer sys­
tem or come into contact with the ground under any circumstances.
- Pay attention to legal requirements when
dispos ing of empty oil containers.
@ Tips
The engine oil consumption may be up to
0.5 quart/600 m iles (0.5 liter/1,000 km), de­
pending on driving style and operating condi­
tions. Consumption may be higher during the
fi rst 3,000 miles (5,000 km). The engine o il
level must be checked regularly.
It would be
best to che ck each t ime you refue l yo ur vehi­
cle and before long dr ives.
Changing the engine oil
We recommend that have your oil changed by an
authorized Audi dealer or a qualified service sta­ tion.
B efore you check a nyth ing in the eng ine compart­
ment,
alw ay s read and heed all WARNINGS ~ .&.
in Working in the engine compartment on
page 159.
The engine oil must be changed according to the
inte rvals spec ified in you r Warranty
& Mainte­
nance booklet. This is very important because the
l ubri cat ing propert ies of o il diminish gradually
d uring normal vehicle use.
Unde r some ci rcumstances the eng ine o il should
be changed more frequently. Change oil mo re of ­
ten if yo u drive mos tly short distances, ope rate
the vehicle in dusty areas or under predominant ly
stop -and -go traffic condit ions, or have your vehi­
cle where temperat ures remain below freezing
for extended periods.
Ch eck ing and Filling
Detergent add itives in the oi l will make fresh oil
l ook dark after the engine has been running for a
short time . This is normal and is not a reason to
change the oi l more often than recommended.
Beca use of the problem o f proper disposal, along
with the specia l too ls and necessary expertise re­
quired, we strongly recommend that yo u have
your o il changed by an authorized
Audi dealer or
a qual ified service stat ion.
If you choo se to change you r oil yourself , please
note the following important info rmation:
A WARNING "--
To reduce the risk of persona l injury if you
must change the eng ine oil in your vehicle
yourself:
- Wear eye protect ion.
-
- To reduce the r is k of burns from hot engine
oil, let the engine coo l down to the touch.
- When remov ing the oil drain plug w ith your
f ingers, stay as far away as possib le. Always
keep your forearm parallel to the gro und to
he lp prevent hot oil from running down your
arm.
- Drain the oil into a container designed for
this purpose, one large enough to hold at least the tota l amou nt of oil in you r engine.
- Engine oil is poisonous. Keep it well out of
the reach of childre n.
- Continuous contact with used engine o il is
harmf ul to your skin. Always protect your
skin by wash ing oil off thoroughly with soap
and wate r.
«I) Note
Neve r mix oil additives with your engine oil.
These additives can damage your engine and
adverse ly affect yo ur Audi limited New Vehi­
cle War ranty.
@ For the sake of the environment
- Before chang ing yo ur oi l, first make sure
you know where you can properly d ispose of
the used oil.
- Always dispose of used engine o il properly .
Do not dump it on ga rden soil, wooded
165

Check ing and F illing
areas, into open streams or down sewage
drains .
- Recycle used engine oil by taking it to a used
engine oil collection facility in your area, or
contact a service station .
Cooling system
Coolant
The engine coo ling system is filled wi th a mixture
of pur ified w ate r a nd coolan t addit ive at the fa c­
tory . T h is coo lant must not be not changed.
The coolant leve l is monito red throug h the . in­
d icator light~
page 13 . Howeve r, we do re com­
mend occasionally check ing the coo la nt level
manually.
I f you must add coolant, use a m ixt ur e of wa ter
and coolant addit ive. M ixing the coolant additive
with d istilled wate r is recommen ded .
Coolant additive
The coolant additive is made of a nti-freezi ng a nd
corros ion protection agents . Only use the fo llow­
i n g coolant add it ives. These additives may be
mixed w it h each other.
Coolant additive Specification
G13 TL774J
G12++ T
L 774 G
The amount of coo lant additive that needs to be
mixed wit h wate r depends on the climate where
the vehicle will be operated . If the coolant addi ­
tive percentage is too low, the coolant can freeze
and damage the engine.
Coolant Freeze protec-
additive tion
Warm reg ions min . 40% m in . -13 °F
max . 45% (
- 25
°()
Co ld regions min. 50% max
. -40 °F
max. 55% (-40 °()
0 Note
- Befo re the start of winter, have your author­
i zed Audi dealer or authorized A udi Service
Fac ility check if the coolant additive in you r
166
vehicle matches t he percentage app ropriate
for the climate . This is especially important
when driving in colder climates.
- If the app ropriate coo lant additive is not
available in an eme rgency, do not add any
other additive. You could damage the en­
gine. If this happens, only use water and re­
store the correct m ixture ratio with t he
specified coo lant add itive as soo n as poss i­
bl e.
- Only ref ill w ith new coolant.
- Radiator sealant must not be mixed with
the coolant.
· Adding coolant
Fi g. 14 3 En gin e compartment: coo lant expa nsio n ta nk
cove r
Observe the safety precautions ~.& in Working
in the engine compartment on page 159 .
Checking the engine coolant level
.. Park the vehicle on a level surface .
.. Switch the ignit io n off.
.. Read the coolant level on the coolant expansion
t ank ~
page 162, fig. 140. The coolant leve l
m ust be be twee n the m arkings when the en­
gi ne i n co ld. W hen t he engine is warm it can be
slightly above the upper mar king.
Adding coolant Requirement: there must be a residua l amount of
coolan t in the expansion tank ~(}).
.,. Let the engi ne cool down .
.. Place a clot h over the coolant expans ion tank
cap and unscrew the cap counte rclockw ise
~ .& -

00
00
......
"' ,....
"' ...... 0 0 :::,
00
~ Add coolant mixed in the correct ratio
¢ page 166 up to the upper marking.
~ Make sure that the fluid level rema ins stable.
Add more coolant if necessary.
~ Close the cap securely.
Coolant loss usually indicates there is a leak. Im­
mediately drive your vehicle to an authorized
Audi dealer or authori zed Audi Service Facility
and have the cooling system inspected. If the
cooling system is not leaking, a loss can come
from the coolant boiling through overheating
and be ing pushed out of the cooling system.
.&, WARNING
The cool ing system is pressu rized and can be­
come very hot. To reduce the r is k of burns
from hot coolant :
- Do not open the coo lant expansion tank cap
when the engine is hot. This increases the risk of burns.
- Stop the engine and allow it to cool.
- Protect your face, hands and arms from es -
caping coolant and steam by covering the
coolant tank cap with a large, thick cloth .
- T urn the coo lant tank cap co unterclo ckwise
slowly and keep light pressu re on the cap .
- T o reduce the risk of burns , do not allow any
antifreeze o r coolant to drip onto the ex­
haust system or hot engine components.
T he ethylene glycol in engine coolant can
catch fire under certain circumstances .
- T he coo lant add itive and the coolant can be
dangerous to your health . For this reason,
keep the coolant in the original container
and away from children. There is a risk of
poisoning.
- When working in the engine compartment,
remember that the radiator fan can switch
on even if the ignition is switched off, which
increases the risk of injury .
Do not add coolant if the expansion tank is
empty. Air could enter the cooling system and
damage the engine. If this is the case, do not
cont inue driv ing . See an authorized Audi deal -
Check ing and Filling
er or authorized Aud i Service Facility for assis ­
tance .
- Before the start of winter, have your author­
ized Aud i dea ler or a uthorized Audi Serv ice
Facility check if the coolant additive in your
vehicle matches the percentage appropriate
for the climate. This is especially important
when driving in colder climates.
- If the appropr iate coo lant add itive is not
availab le in an emergency, do not add any
other additive . You could damage the en­
gine. If this happens, only use water and re­
store the correct m ixtu re ratio with the
specified coolant add it ive as soo n as poss i­
ble .
- Only refill w ith new coolant.
- Radiator sealant must not be mixed with
the coolant .
Radiator fan
T he radiator fan switches on automatically by it ­
self.
An auxiliary e lectr ic radiator fan switches on and
off depend ing on coolant temperature and other
vehicle operating conditions.
After you switch the engine off, the auxiliary fan c a n continue running for up to 10 m inutes - even
with the ignition off . It can even switch on aga in
later by itself ¢.& , if
- the temperature of the engine coolant rises due
to the heat build-up from the engine in the en­
gine compartment, or
- the engine compartment heats up bec ause the
veh icle is parked in in tense sunlight.
.&, WARNING
--
- To reduce the r isk of personal injury never
touch the radiator fan .
- The auxiliary e lectr ic fan is temperature
controlled and can switch on s uddenly even
when the engine is not runn ing .
- The auxiliary radiator fan sw itches on auto ­
mat ica lly when the eng ine coolant reaches a
certa in temperature and will continue to run
until the coolant temperature d rops .
167

00
00
......
"' ,....
"' ...... 0 0 :::,
00
tires according to the load and
the size of the tires installed .
Model/
Tire designation
Engine
Wheels
Tire pressure
Normal load Maximum load
(up to 3 people)a>
front rear front rear
PSI
Q3: 235/50 Rl8 97H
32 2.0L All Season
4 cylinders 235/50 Rl8 97V
High Performance
32
255/40 Rl9 l00Y
33 High Performance
255/35 R20 97Y
33 High Performance
255/40 Rl9 l00H
33 All Season
a) 2 people in the front, 1 person in the rear
A WARNING
Please note the important safe­
ty precautions regarding tire pressure
c:::> page 181 and load
limits
c:::> page 183.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop.
Overloading can not only lead to
loss of vehicle control, but can al­
so damage important parts of the
vehicle and can lead to sudden
tire failure, including a blowout
kPA PSI kPA PSI kPA PSI
220 32 220 33 230 36
220 32 220 33 230 36
23 0 33 230 44
300 4
6
230 33 230 44 300 46
23 0
33 230
44 3
00 4
6
and sudden deflation that can
cause the vehicle to crash.
kPA
250
250
320
320
3 20
Your safety and that of your pas­
sengers also depends on making
sure that load limits are not ex­
ceeded. Vehicle load includes ev­
erybody and everything in and on
the vehicle . These load limits are
technically referred to as the vehi­
cle's
Gross Vehicle Weight Rat­
ing
("GVWR").
The "GVWR" includes the weight
of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids
plus maximum load. The maxi­
mum load includes the number of.,.
183

00
00
......
"' ,....
"' ...... 0 0 :::,
00
Engine compartment fuse assignment
The fuse number is stamped into the plastic be­
low or above each fuse.
No. Equipment
1 Transmiss ion supply
2 ESC
3 Horn
4 DC/DC
converter
5 BCM, battery data module
6 BCM (right)
7 Washer fluid pump
8 BCM (left)
9 Seat adjustment lumbar support
10 Glow time
control module, fuel pump,
heated oxygen sensor
11 Steering
column lever, multifunction
steer ing whee l controls
1 2 Cell phone adapter
13 En
gine control module
14 Engine control module
15 Gateway
16 Heated oxygen sensor, fuel pump, eng
ine
components
17 Engine components
18 Fue
l pump control module
19 Sound amplifier, DC/DC converter
20 Clutch pedal sensor, brake light sensor
22 Windshield wipers Radiator fan, engine components, coolant
23 recirculation pump, auxiliary
heater, fuel
pump relay coils
24 Ignition coils
25 Driver's door
control module (central lock-
ing, window regulators)
26 Front passenger's door control module
(centra
l locking, window regulators)
27 Term inal 15 supply
29 Power seat adjustment (driver,
front pas-
senger)
30 ESC
Fu ses an d bulb s
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you .
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­
moved before you are able to get to the bulb .
T his applies especially to the light bulbs in the
front of your car which you can only reach
through the engine compartment .
Sheet metal and bu lb holders can have sharp
edges that can cause serious cuts, pa rts must be
correctly taken apart and then properly put back
together to help prevent breakage o f parts and
long term damage from water that can enter
housings that have not been properly resealed.
For your safety, we recommend that you have
your authorized Aud i dea ler rep lace any bulbs fo r
you, since your dealer has the proper tools, the
correct bulbs and the expertise.
Gas di schar ge la mps (Xe no n ligh ts):
Due to the high electr ical voltage, have the bulbs
rep laced by a qualified technician. Headlights
with Xenon light are identified by the hig h volt­
age st icker.
LED headlights* require no maintenance . Please
contact your authorized Audi dea ler if a bulb
needs to be replaced.
_&. WARNING
Changing Xenon lamps wi thout the necessary
equipment can cause serious personal injury .
- Bulbs are pressu rized and can explode when
be ing changed. Potent ial ris k of injury!
- On veh icles equipped with gas disc harge
bu lbs (Xenon light) life-threatening injuries
can resu lt from improper handling of the
high-vo ltage portions of such lamps!
- Only your authorized A udi dealer or quali­
f ied workshop sho uld change the bulbs in
gas discharge lamps. There are parts with
sharp edges on the openings and on the
207

Emergency situations
distribut ion and ba lance . This might hap ­
pen, for example, when heavy compo­
nents such as the engine block or trans­
miss io n are removed.
- When removing heavy components like
th ese, a nch or vehicle to ho ist o r add corre­
sponding weights to maintain the cen ter of
gr avity. Otherwise , th e vehicle migh t ti lt or
s lip off the hoist, causing s erious p erso nal
rnJury.
0 Note
- Be aware of t he following poi nts before lift­
i ng t he veh icle:
-The vehicle should never be lifted or
jacked up from underneath the engine oil
pan , the transmission housing, the front
or rear axle or the body side members.
This could lead to serious damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in·
serted between the floor jack and the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist .
- Before driving over a workshop hoist, en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the ve ·
hide .
214

a:,
a:,
.... N
" N .... 0 0 ::, a:,
Technical data
Vehicle specifications
XXXXX XX · X · XXXX XXX xx
CD-+ IAH RIG.- IOENT • NII. VOE£ • WIT • Nil. XXXXXX XX XX X XX XXX XXX
IYP/TYP! XXX XXX
xx xxxxxxx xx xx xx
XXX KW XXX
a.;. C1lll /TRANS. lllllE xxxx XXX XXX ®i 11)10Al<8 ./lil1R.k8.
©+ I.AO OIR. / IN NENAllSSl.
XXXX I XXXX XXX I XX PAI NT IIO. / ffT£ml
II. • AIJSlit / OPTIONS
EOA 70 5 4U B 6XM SSG SRW
2 EH JO Z 1LB 1AS l BA
3FC SM U 7Xl
F O A 9G3 OG7 OYH OJF
TL 6 3KA 8EH UlA X 9B OZ7
l XW
803 908 8Z4 020
7T6 CV7 7KO 4X3 2K 2
3 L4 4KC 3YO 413 50 2
lS A 7GB 01A 4GO
XX . X XX X XX X
xxxx
Fig. 173 Vehicl e identifica tion labe l
Vehicle Identification Number (VIN)
The VIN number is located in the following pla­
ces :
0
0
a, '? :x: .,. al
-In the Infotainment system: se lect: the !CARI
func tion button > (Car}* systems control but­
ton
> Servicing & checks > Vehicle ID number
(VIN).
- under the windshield on the driver's side*
- on the vehicle identification label
Vehicle identification label
The vehicle identification label¢ fig. 173 is locat­
ed in the luggage compartment under the cargo
floor cover .
T he information of the vehicle identification label
can also be found in your Warranty
& Mainte­
nance booklet.
The sticker contains the following vehicle data :
@ Vehicl e Identification Number (VIN)
@ Veh icle type, engine output, transmission
@ E ng ine and transm ission codes
Technical data
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
The safety compliance sticker is your assurance
that your new vehicle complies with all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu­
factured. You can find this sticker on the door
jamb on the driver's side .
It shows the month and
year of production and the veh icle identificat ion
number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the
Gross Axle We igh t Rating (GAWR).
High voltage warning label
The high voltage warning label is located in the
engine compartment next to the engine hood re­
lease. The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle We ight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a sticker on the door jamb
o n the driver's side.
The Gross Vehicle We ight Rating includes the
we ight of the bas ic vehicle plus fu ll fuel tank, oil
and coolant, plu s maximum load, which includes
passenge r weight (1S0 lbs/68 kg per designated
seat ing position) and luggage weight¢.& .
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum
load that can be applied at each axle of the vehi­
cl e ¢ _& .
Vehicle capacity weight
The vehicle capacity weight (max. load) is listed
on the dr iver 's side 8-pillar .
Roof weight
The maximum p ermissible roof we ight is 165 lb
(7 5 kg). The roof weight is the total of the
weight of the roof rack, the attachments and the cargo you are carrying . ..,.
215