navigation system AUDI Q5 2008 1.G Infotainment MMI Operating Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2008, Model line: Q5, Model: AUDI Q5 2008 1.GPages: 193, PDF Size: 6.18 MB
Page 89 of 193
Using the telephone87
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Using the telephone
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Introduction
You can operate a mobile phone* or the handset conveniently via
the MMI system. It does not matter whether the mobile phone is
connected to the Bluetooth car telephone kit or the phone pre-
installation. The basic operation via the MMI control console is
always the same.
Many telephone functions that you are familiar with from your land
line or your mobile phone are available in your vehicle: You can
answer and end calls, place calls on hold and go back and forth
between two separate calls (switching calls). In addition, you can
access the MMI directory, the phone book on your SIM card and the
phone book on your mobile phone.
When you place or receive telephone calls the audio source is
muted automatically and the current media drive is paused. A
crossed-out loudspeaker will appear in the display when the system
is muted. After the call the audio source will return to its previous
volume.
You can set the system so that it will switch off the navigation* voice
guidance during phone calls if desired page 119.
Caution
•You must switch off the telephone system via the MMI menu
(Setup Telephone) in areas where the use of mobile telephones is
prohibited. Please observe all relevant caution notices and regula-
tions.
•Switch off the car telephone kit, the handset* page 140 and
any other mobile phones in all areas where there may be a risk of
explosion. Remember that these areas may not always be
adequately marked. Such places are filling stations, fuel and chem-
ical storage facilities or transport vehicles and other places where fumes, chemicals (e.g. from leaking propane or fuel vapours in vehi-
cles or buildings) or large quantities of dust particles (e.g. from
flour, wood or metal) could accumulate in the air. This warning also
applies to all other places where you would normally switch off your
engine.
Note
The telephone functions will depend on the mobile network service
provider and the mobile phone used. For more information, contact
your service provider.
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Requirements for using the
telephone
If you want to use the telephone function of your MMI system, one
of the following requirements must be met:
•A mobile phone must be connected to the Bluetooth car tele-
phone kit page 24, or
•A handset* must be connected to the Bluetooth car telephone kit
page 27, or
•A mobile phone must be connected to the phone pre-installation
page 19.
In vehicles fitted with a Bluetooth car telephone kit, the car tele-
phone must be switched on page 26.
Page 106 of 193
Navigation 104
Navigation
Applies to vehicles: with navigation system
Introduction
Let the “Global Positioning System” (GPS) guide you to
your destination.
Wasting time studying confusing maps and tediously planning
routes are things of the past! Now you can simply enter your desired
destination into the navigation system, and the route guidance will
guide you directly to it. You can also set up to three stopovers on the
way to your destination.
The route guidance will be transmitted in the form of spoken cues
that will inform you in good time of any necessary turns, stops etc.
In which language would you like to hear the route guidance? You
can select any of the following languages: German, English, French,
Italian, Portuguese, Spanish or Dutch. You can have the last route
guidance cue repeated by pressing the right-side thumbwheel on
the multi-function steering wheelpage 137.
A detailed route map is displayed on the MMI screen page 110.
You can also receive information on your route via the driver infor-
mation system page 111.
If you do not want to follow a certain route guidance cue, no
problem! The navigation system will re-calculate the route from the
current location of the vehicle. In addition, if the dynamic navigation
function is activated, the navigation system will even take into
account traffic reports so that you can reach your destination even
faster.
If the vehicle is located in a place that cannot be identified by the
software (e.g. car park), a speech cue will inform you of this.
WARNING
•Today's driving conditions require the full attention of drivers.
Please see page 9, “Notes on traffic safety”.
•Pay attention to traffic rules when driving.
•The route calculated by the navigation system is a recommen-
dation of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Caution
•Should the navigation directions contradict the current traffic
regulations, you must always follow the traffic regulations.
•The volume should only be set at a level which enables you to
hear distant police and emergency vehicles clearly - failure to do so
could result in an accident.
Note
•Snow or other obstructions on the GPS aerial or interference
caused by trees or large buildings could affect the reception of the
satellite signals and make positioning difficult. GPS reception and
vehicle positioning can also be adversely affected by deactivation or
a malfunction of several satellites.
•Street and town names can change, therefore the names stored
on the DVD can in some cases be different from the names that have
since been changed.
•The navigation DVDs can only be purchased from Audi dealers.
They can also provide you with information on the most recently
updated navigation DVDs.
Page 107 of 193
Navigation105
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with navigation system
Activating navigation mode
Important: The MMI system must be switched on
page 40, and a navigation DVD must be inserted in the
drive page 14.
– Press the function selector button. The entry space
fig. 91, the Route plan menu fig. 93 or the naviga-
tion menu that was last activated will appear on the MMI
display.
The menu that was active when you last used the navigation system
will appear on the MMI display. Call up the entry space or the Route
plan menu by pressing the function selector button again
(while in navigation mode).
Note
•Press the right-side thumbwheel on the multi-function steering
wheel* page 128 to have the last spoken voice guidance cue
repeated.
•You can also start the navigation in demo mode page 120 if
you want a simulation.
Entering a destination
Applies to vehicles: with navigation system
Entering a route with and without stopover(s)
You can choose whether you would like to enter a single
destination (Route without stopover) or up to three stopo-
vers (Route with stopover).
Important: The navigation mode must be activated
page 105, and an entry space for a single destination
fig. 91 or a route plan fig. 93 must be displayed.
Fig. 91 Entry space
NAV
NAV
Fig. 92 Route with
stopover
Fig. 93 Route plan
Page 108 of 193
Navigation 106
Route without stopover
–When the Route plan appears on the MMI display
page 105, fig. 93, the MMI system is set for the option
Route with stopover. Press the control button for Route.
The option Route without stopover will appear on the
MMI display.
– Turn the rotary pushbutton to Route without stopover.
– Press the rotary pushbutton. The entry space for a single
destination will now appear in the MMI display
page 105, fig. 91. The navigation system is now set for
route guidance without stopover(s).
Route with stopover
– When the entry space for a single destination appears on
the MMI display page 105, fig. 91, the MMI system is
set for the option Route without stopover. Press the
control button for Route. The option Route with stopover
will appear on the MMI display.
– Turn the rotary pushbutton to Route with stopover
page 105, fig. 92.
– Press the rotary pushbutton. The Route plan will appear
on the MMI display page 105, fig. 93. The navigation
system is now set for route guidance with stopover(s).
The navigation system remains in the mode which is currently set
until you change it. For example, if you have selected the mode
Route with stopover for a journey which you have completed, the
navigation will stay in this mode until you manually set the mode
Route without stopover.
Applies to vehicles: with navigation system
Notes on entering a destination
To w n s
While you are entering the data, the system will offer you towns
which you have visited in the past. The proposed town appears in
the speller entry field fig. 94. Further towns matching your entry
are listed below the speller entry field. The total number of towns
found is displayed in the bottom right-hand corner fig. 94.
If the desired town is displayed in the speller entry field, you can
select the town from a list by pressing and holding the rotary push-
button.
Selecting “Centre (end entry)”
The navigation system will calculate a route leading to the centre of
the selected town.
Selecting “Street”
After entering a street name you can also define your destination
more specifically by entering an Intersection or House number.
Selecting “Special destination in town”
You can select a special destination in the specified town as your
destination. For example, you can navigate directly to tourist attrac-
tions or public buildings (e.g. hospital, cinema, recreation areas).
Fig. 94 Entering a
destination via the
speller
AA
!
Page 109 of 193
Navigation107
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control If you would like to find a special destination without entering a
specific town, select Special destination page 116 from the navi-
gation menu after selecting the country.
Selecting “Select destination on map”
You can also set your destination via the map display.
Once the map for the selection of a destination is displayed, cross-
hairs will appear in the centre of the corresponding town. You can
then specify a new destination by moving the crosshairs vertically
and horizontally page 109.
Applies to vehicles: with navigation system
Single destination (route without stopover)
For a single destination the country and town must
always be specified. You can specify the destination
further by entering an address or a special destination.
Important: The system must be set to Route without
stopover page 105.
– If the entry space page 105, fig. 91 does not appear in
the MMI display, press the function selector button
marked .
– Turn the rotary pushbutton and select Country.– Press the rotary pushbutton. Using the rotary push-
button, you can now select a country from the list and
then copy it into the entry space by pressing the rotary
pushbutton.
– Turn the rotary pushbutton and select To w n / Z I P.
– Press the rotary pushbutton. The speller will appear on
the MMI display page 43.
– Enter the town or the ZIP code via the speller.
– To complete the entry, turn the rotary pushbutton to
Centre (end entry) and press to confirm, or
– To enter additional data on the navigation destination,
turn the rotary pushbutton to Street, Special destination
in town or Select destination on map and press to
confirm.
– Enter the additional information.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
To add a house number or intersection after entering the destina-
tion, select the line fig. 95 and complete your entries.
Note
•If your navigation destination contains special characters such
as the dashes in “Stratford-upon-Avon”, simply switch between the
speller for letters and the speller for numbers page 43.
Fig. 95 Entering a
house number/inter-
section
NAV
A1
Page 110 of 193
Navigation 108
•To have the last route guidance cue repeated, press the control
button Nav-Info page 118 or the right thumbwheel on the multi-
function steering wheel page 129.
Applies to vehicles: with navigation system
Route plan (route with stopovers)
You can enter up to three stopovers and a final destina-
tion in the route plan.
Important: The system must be set to Route with stopover
page 105.
– If the Route plan fig. 96 does not appear in the MMI
display, press the function selector button .
– Turn the rotary pushbutton and select Destination.
– Press the rotary pushbutton. The entry space will appear
in the MMI display page 105, fig. 91.
– Enter the navigation destination page 107.
– To enter stopovers, turn the rotary pushbutton to Stop 1,
Stop 2 or Stop 3.– Press the rotary pushbutton. The entry space will appear
in the MMI display page 105, fig. 91.
– Enter the stopovers (see page 107).
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Note
•If you would like to change your route plan, no problem! Simply
use the rotary pushbutton to select the destination or stopover and
then press the rotary pushbutton. Now you can change or delete the
destination or stopover or move the stopover.
•If your navigation destination contains special characters such
as the dashes in “Stratford-upon-Avon”, simply switch between the
speller for letters and the speller for numbers page 43.
•To have the last route guidance cue repeated, press the control
button Nav-Info page 118 or the right thumbwheel on the multi-
function steering wheel page 129.
Applies to vehicles: with navigation system
Changing the route guidance
You can change a route guidance plan at any time.
Important: The route guidance function must be activated
page 105.
– Press the function selector button.
– Enter new information for the single destination or a
destination/stopover of the route plan page 105.
Fig. 96 Route plan
NAV
NAV
Page 111 of 193
Navigation109
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Applies to vehicles: with navigation system
Setting a destination from the map
A point on the map can be set as a destination or stop-
over, stored in the directory and called up on the tele-
phone.
Important: The route guidance function must be activated
page 105.
Activating the map legend menu
– Press the Map control button. A map will appear on the
MMI display.
– Press the rotary pushbutton. The map legend menu will
now be activated, and the crosshairs will appear in the
map display fig. 97.
Changing the map scale
– Turn the rotary pushbutton to position and press the
rotary pushbutton. You can now zoom out of or zoom in
on the map by turning the rotary pushbutton.
– Press the rotary pushbutton again to leave position .
Moving the crosshairs
– Turn the rotary pushbutton to position .
– Press the rotary pushbutton. Using the rotary push-
button, you can now move the crosshairs horizontally.
– Press the rotary pushbutton again. Using the rotary
pushbutton, you can now move the crosshairs vertically.
– To deactivate the moving crosshairs function, press the
rotary pushbutton again.
Setting a destination
– To set a selected point in the map as the destination, turn
the rotary pushbutton to position .
Fig. 97 Changing a
destination with the
crosshairs
Fig. 98 Calling a posi-
tion on the map
A1
A1
A3
A2
Page 112 of 193
Navigation 110
– Press the rotary pushbutton. Now you can set the
selected point as a destination or a stopover, store it in
the directory or even call* it if a number is stored for the
selected point page 109, fig. 98.
Note
If you do not move the crosshairs for a moment, you will receive
detailed information on the position of the crosshairs (e.g. town or
street name).
Applies to vehicles: with navigation system
Stopping the route guidance
Important: The route guidance function must be activated
page 105.
– Press the function selector button.
– Turn the rotary pushbutton and select Stop route
guidance.
Note
The previously entered data and settings remain unchanged even
when you cancel the route guidance.
Display
Applies to vehicles: with navigation system
On the MMI display
As soon as you press the Map control button (while the route guid-
ance is activated), the map will appear on the MMI display with the
legend menu deactivated fig. 99.
In this display, you can zoom in and out of the map. To do so, turn
the rotary pushbutton clockwise or anti-clockwise.
You can activate the legend menu fig. 100 by pressing the rotary
pushbutton. Now you can change the map display via the legend
menu. To do so, turn the rotary pushbutton to select the point on the
map and press the rotary pushbutton.
NAV
Fig. 99 Map with deac-
tivated legend menu
Fig. 100 Map with
activated legend menu
Page 113 of 193
Navigation111
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control You can exit the legend menu by pressing .
Orientation. The map is displayed either facing north or facing
the direction of travel page 118. If you select the orientation
option in the activated legend menu and press the rotary push-
button, the orientation switches from the direction of travel to
the direction facing north and vice versa. This setting is not
stored.
Scale. Turn the rotary pushbutton clockwise/anti-clockwise to
zoom in or out. You can also change the scale via the activated
legend menu. The setting that was last activated is stored.
Distance to the destination
Estimated time of arrival
Examples of selected map contents
Depiction of motorway exits on a scale of 50 m to 500 m. On a
scale of 750 m to 8 km the exits are displayed as dots.
Location of the vehicle
Destination control button. To switch to entry space
page 105, fig. 91 or the route plan page 108, fig. 96.
If you use the crosshairs to select map contents, any existing
information on the contents (e.g. address, phone number) will
be displayed. If you select a traffic jam symbol and press the
rotary pushbutton, the corresponding TMC traffic report will be
displayed. On a scale of 1 km upwards, the map contents will
not be displayed.
Display of position coordinates of the crosshairs (longitude and
latitude).
Map position menu. The point on the map selected with the
crosshairs can be set as a destination or stopover, stored in the
directory and called up on the telephone page 109.
The crosshairs can be moved horizontally and vertically by
turning and pressing the rotary pushbutton. Press the rotary
pushbutton to switch between the horizontal and vertical cross-
hair bars or deactivate this option. Using this option, you can,
for example, select a new destination page 109.Moving along the route. This function can be used while route
guidance is activated. Turn the rotary pushbutton clock-
wise/anti-clockwise to move the map along the current route.
Altitude display
Note
Did you know that you can choose from four different map types
page 118?
Applies to vehicles: with navigation system
In the driver information system
RETURN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
Fig. 101 Display when
a lane change is
required
Fig. 102 Display when
a turn-off is required
Page 114 of 193
Navigation 112
After you have entered a destination or a route and have started the
route guidance, the navigation information is displayed in the driver
information system. If you select another function (e.g. radio) using
the multi-function steering wheel, the navigation will briefly be
replaced by the function selected page 128.
Distance to turn-off
Estimated time of arrival
Total distance to destination/next stopover
Name of motorway, major road or street you are driving on. An
arrow in front of the street name indicates that you are
supposed to turn into the street.
Arrow indicating a turn-off. A necessary lane change before the
turn is also displayed.
Bar graph. If an arrow is displayed, a bar graph will also appear.
The fewer bars are displayed, the shorter the distance to the
turn-off point.
WARNING
The route calculated by the navigation system is a recommenda-
tion of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Note
An exclamation mark “!” in front of the street name indicates that
the navigation DVD does not contain all the information on this
street or street section. Pay attention to traffic rules such as one-way
streets or pedestrian zones.
Storing a destination
Applies to vehicles: with navigation system
In the directory (single destination)
A single destination can either be stored as a new entry or
added to an existing entry.
Important: You must have entered a single destination
page 107.
Storing a destination as a new entry
– Press the Memory control button.
– Turn the rotary pushbutton to Store in directory and
press to confirm.
– Turn the rotary pushbutton and select New entry.
– Press the rotary pushbutton. An entry space will now
appear fig. 103.
– Turn the rotary pushbutton to Surname and press the
rotary pushbutton. The speller will appear on the MMI
display page 43.
– Enter the surname using the speller.
A1
A2
A3
A4
A5
A6
Fig. 103 Address card