light AUDI Q5 2013 User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2013, Model line: Q5, Model: AUDI Q5 2013Pages: 316, PDF Size: 78.89 MB
Page 18 of 316

16 Instrum ent s and w arn ing /indic ato r light s
blink, then there is a ma lfunction somewhere
in the system.
If the light does not illuminate
when you switch the ignition on, this also
means there is a malfunction.
A WARNING
If you have a malfunction in the safety sys
tems, contact your author ized Audi dealer
immediately. Otherw ise the safety sys
tems may not work properly in an acci
dent.
U) Tire pressure monitoring system -
telltale indicator lamp
Appl ies to vehicles: with tire pressure monitoring system
The warning/indicator light appears in the
event of a significant loss of tire pressure or if there is a malfunction.
The indicator light IE illuminates to check
the function when you switch on the ignition.
If the
IE symbol remains on or blinks after
you switch on the ignition, the re is a loss of
tire pressure or a system malfunction.
If there
is a system malfunction, see your authorized
Aud i dealer as soon as possible.
Detai led information on the tire pressure
mon itoring system can be fou nd in
¢page 266.
¢ Q Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left B or the right II
turn signal, the ind icator light blinks. When
you use the emergency flashers, both indica tor lights flas h.
If one of the turn s ignal light bulbs burn out,
the turn signa l wi ll blink tw ice as fast as nor
mal.
This does not apply, however, in towing mode.
The indicator light does no t flash if a turn s ig
nal is out on the trailer or the tow ing vehicle.
Addit ional info rmation on the turn sig nals
¢page 52.
~,1 ¢ Trailer turn signal assembly
Applies to vehicles: with towing hitch
The indicator light also blinks if the turn sig
nal is operated when towing a trailer.
The ind icator light. bli nks when the turn
s ignal is used, if a trailer has been properly
con nected to the vehicle .
If one of the turn signa l bulbs on the trailer is
burned out or defective, the ind icator light
will not blink when you use the turn signals.
(D Tips
For vehicles with a factory installed towing
hitch or a trailer hitch that was installed
l ater according to factory spec ificat ions,
the trailer turn signal assembly is actuat
ed.
,(t Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warn ing/ indicator light illum inates
when the ignition is switched on to remind
the driver and (o n USA models only) any front
passenger to put on the safety be lt . Addit ion
ally, an audib le warn ing tone w ill also sound .
For more Informat ion
¢ page 149, Safety
belt warning light.
o Malfunction Indicator Lamp (MIL )
The Ma lfunction Indicator Lamp (MIL) is part
of the On-Board Diagnos tic (OBD II) sys tem.
T he symbo l
(4 lights up when the ignition is
tu rned on and will turn off after the eng ine
has started and has settled at a constant idle
speed. This indicates that the MIL is working
properly.
The warning light ill uminates when the re is a
malfunction in the engine electronic system.
Contact your a uthorized Audi dea ler and have
the malfunction corrected. .,..
Page 19 of 316

Instruments and warning/indicator lights 17
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
c::> page231.
F or mo re in forma tion
c::> page 26.
!§:D High beam
The II warning/indicator light illuminates
when the high beams are on o r whe n you use
the head light flasher. For mo re in format ion
about us ing the high beams, see
c:> page 52 .
CRUISE/"(-) Cruise control
The M;\1)~14 (USA models) Iii (Canada models)
war ning/ indica to r li ght illum inates when the
cru ise contro l is act ivated.
ABS/( @) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and th e electronic differ ential lock (EDL).
The
E (USA models) I ii] (Canada models)
warn ing/ indicato r light w ill come on for a few
seconds when the ig nition is swi tc h ed o n. The
light w ill go ou t aft er an au tomatic check se
qu enc e is co mple ted .
There is a malfunction in the ABS when :
-The warni ng/ indicator lig ht d oes not ill umi
nate whe n you switc h on the ignition .
- The warning/ indicator lig ht d oes not go out
after a few seconds .
- The warning/ ind icator lig ht ill uminates
wh ile driving.
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more informat io n regarding the ABS
c:> page 19 7.
The ABS warn ing light and the brake warn
ing light come on together. The ABS will not
work and you will notice a change in braking
re sponse and performance . Malfunction in the brake system
If t
he bra ke w arn in g ligh t c::> page 18 and
t he A BS warning ill uminate together there
may be a malfunction in the ABS, and the re
may also be a malfunction in the brake system
i tse lf
c:> A .
In the even t of a malfunction in the brake
system
the warning/ind icator light 1111
( U SA mode ls)/ . (Canada models) in the in
strument cl uster flashes. By press ing the
jsET I
button , yo u can br ing up a d river message
which expla ins the malfunct io n in more de
t a il. Please no te
c:> pag e 29.
Malfunction in the electronic differential
lock (EDL)
The EDL works together w ith the ABS . The
ABS wa rning lig ht w ill come on if there is a
malfu nction in the EDL sys tem
c:> page 197 .
See your author ized Audi dealer as soo n as
p oss ibl e.
_&. WARNING
- If the li!I (USA m ode ls)/ [I] (Canada
mo dels) warning light does not go ou t,
or if it comes on whi le dr iving , th e ABS
system is not wor king pro per ly . The vehi
cle can then be sto pped on ly w it h the
standa rd b rakes (with out ABS). You w ill
not have the protect io n ABS p rov ides .
C ontact your au thorized A udi dealer as
s oon as p ossibl e.
- USA models: If the
1111 warning light
an d th e
m:SJ war ning light come on to
g eth er, the rear wheel s co u ld loc k up
first under h ard br akin g. Rear w heel lock
u p ca n caus e loss of vehicle control and
a n accident . H ave yo ur vehicle re pa ire d
imme diate ly by yo ur authorize d Au di
dea le r o r a qua lified wor kshop . Drive
slowly and avo id sudden, hard brake ap
plications .
- Canada models: If the brake warning
light . and the ABS warning li ght
ii]
come on togethe r, the rear wheels could
l o ck up first und er hard braking. R ear
-
Page 20 of 316

18 Instrum ent s and w arn ing /indic ato r light s
wheel lock- up can cause loss of vehicle
control and an acc ident. Have your vehi
cle repaired immediately by your author
ized Audi dea ler or a qualified workshop.
Drive slowly and avo id sudden, hard
brake applicat ions .
1:1.\.f(®) Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake.
W ith the parking brake app lied and the igni
tion turned on, the. (USA models)/ . (Can
ada models) warning/ind icator light illumi
nates . After the ignition has been turned off,
the warning/ind icator light continues to i llu
minate for about 30 seconds. If the parking
b rake is applied with the ignition turned off,
the warning/ind icator light illuminates for
about 30 seconds .
The warning/indicator light will go out when
the park ing brake is released.
If the war ning/ indicator light flas hes cont i nu
ously
after appl ying the park ing b rake, brak
ing fo rce is not sufficient to preve nt the vehi
cle from roll ing uninten tionally. Please no te
the following:
- If the slope of the g round is too steep to
par k the vehicle , the add itiona l dr ive mes
sage appea rs
Caution: Vehicl e parked to o
steep.
- In the event of a par king brake malfunct ion,
the ye llow
Ill symbol appears in the inst ru
ment cluster d isplay and the dr iver message
Parking b rake malfunction! is displayed.
Have the malfunction repaired as soon as
possible by an authorized A udi dealer or any
other qualified workshop.
BRAKEl< CD> Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction.
The .. (USA mode ls) • (Canada models)
light ill uminates when the ign ition is turned on
. It goes out afte r the engine has been
started. This indicates that the brake warning
li ght is functioning properly.
If the br ake w arning light do es not light up
when the engine i s cranking , there ma y be a
malfunction in the elect rical sy stem . In thi s
ca se , conta ct an authorized Audi dealer .
If the brake sys tem warn ing/in dicator light
flashes, there is a b rake system ma lfunction.
By pressing the
! SET ! button, you can bring up
a driver message wh ich explains the malfunc
t ion in more detail
c> page 29.
If the ABS fai ls, the ABS warning/indicator
li ght
r4:B (USA models)/ 11] (Canada models)
flashes together with the brake system warn
ing/indicator light
c> &. .
(USA mode ls): If the warning light .. and
the warning light
Ei] ill uminate together, im
med iate ly contact your authorized Aud i dea ler
or qualified workshop to have all brake pads
inspected
c> page 33.
When the light comes on, an audible warning
s ignal is also given .
&_ WARNING
--= =
-USA models: If the .. warning light
and the
a warning light come on to
gether, the rear whee ls could lock up
fi rst under hard braking. Rear wheel lock
up can cause loss of vehicl e co ntrol and
an ac cident . Have yo ur vehicle repaired
immed iate ly by yo ur au thori zed Aud i
dealer o r a q ua lified workshop. Drive
slowly and avoid sud den, hard brake ap
plications .
-Canada models: If the brake warning
light . and the ABS warn ing light
[iJ
come on together, the rear wheels could
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
control and an accident . Have your vehi
cle repaired immed iately by your author
ized Audi dealer or a qualified workshop .
Dr ive s low ly and avoid s udden, hard
b rake applications.
~
Page 21 of 316

Instrument s and warnin g/indic ator ligh ts 19
-If the brake warning/indicator light does
not go out after a few seconds and the
park ing brake is released, or lights up
wh ile you are driving, the fluid level in
the brake fluid reservoir is too low . If you
believe that it is safe to do so, proceed
immediately at low speed to the nearest
authorized Audi dealer or qualified repair
facili ty and have the brake system in
spected.
- Always keep in m ind that after several
brake applicat ions, you will need g reater
pressure on the brake peda l to stop your
vehicle. Do not re ly on strained brakes to
respond w ith maxim um stopp ing power
in critical situations. You must allow for
increased braking distances. The extra
distance used up by fad ing brakes could
lead to an acc ident.
Page 22 of 316

20 Driver information display
Driver information
display
Introduction
General notes
The driver information display inside the in
strument cluster provides you, the driver,
with much useful information.
Fig. 9 Instrument cluster: center display
Information from the driver information sys
tem is shown in the display in the center of
the instrument cluster.
When you turn on the ignition and while you
are driving, some functions and vehicle com
ponents are scanned for their operat ing sta
tus. Malfunctions or required service proce
dures are signaled audibly and shown by red
and yellow lighted symbols and reminders to
the driver in the display.
The driver is also shown information about ra
dio and CD operation and directions for the
navigation system*. You can find additional
information on these subjects in the radio or
MMI* manual.
The illustr ations in the instrument panel dis
play differ in some of the vehicles .
The driver information system provides the
following functions:
Sound system display
¢page20
Outside air temperature r:::;, page 21
Digital speedometer r:::;, page 21
Open door- and luggage com-llr:::;, page 21
partment warning
Service interval display
¢page 22 r:::;,page
27
Driver information r:::;,page 27
Speed warning r:::;,page93
Trip computer r:::;, page 23
Tire pressure monitoring sys-r:::;, page 266 1
tern*
Digital clock with date dis play
r:::;, page 12
Odometer and trip odometer ¢page 13
Selector lever position r:::;, page 123
¢page95
Adaptive cruise control* Energy flow display* ¢page 107
---,.--
r:=;,page 103
¢j) Tips
In the event of a malfunction either a red
or yellow icon appears in the display. Red
symbols indicate
Danger r:::;, page 28. Yel
low symbols indicate a
Warning
¢page 31.
Sound system display
Fig. 10 Display: sound system
(0
"' .... 9 a:
~
If priority 1 or priority 2 faults are not shown
by the Auto Check Control, the name of the ra
dio station you are tuned to or the frequency
and the reception range are shown in the up
per area of the displ ay.
When the CD is in use , the title of the track
being played is shown. The CD changer dis
plays the number of the current CD (CD
1 to
CD6).
Page 23 of 316

Outside temperature display
Fig. 11 D isplay : outside te mpe rature
At temperatures below 39 °F (+4 °C), a snow
f lake symbol appears in front of the tempera
ture display . It is intended to rem ind the driv
er to pay special attent ion to
ice on the roa d.
If the vehicle is stationary, or if you are driving
at a very low speed, the temperature shown in
the display might be slightly higher than the
actual outside temperature . Th is is caused by
the heat being radiated from the engine .
The unit of measurement for the temperature
can be set in either °For in °Con the MMI* or
on the radio control un it . The outside temper
ature display automatical ly shows the unit of
measurement that has been set. For addition
a l information, see the MMI* or the radio in
struction manua l.
A WARNING
- Never use the outside temperature d is
play to determine if a road surface is icy
or not. Keep in mind that road surfaces ,
especially bridges and overpasses, could be ice covered and slippery even at an
outside temperature above 39 °F (+4 °C).
- Always remember, eve n if the "snow
flake" symbol ( ice warn ing) does not ap
pear i n the display, black ice could be on
the road .
-Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encounte ring icy
road surfaces increases .
Driver inform ation di spl ay 21
Digital speedometer
Fig. 12 D ispl ay : D ig it a l speedometer
Current speed appears in the disp lay. Speed is
shown in 1 mph increments (USA mode ls) or 1
km/h increments (Canada models) .
You can switch the disp lay from mi les to kilo
meters and vice versa via the radio or MMI* .
Open door or trunk lid warning
The pictogram alerts you when doors or the
trunk lid have been left open .
Fig. 1 3 Disp lay: Open doo r· and tr unk lid wa rnin g
T he Open Door/Trunk L id warn ing displays if
even one door, the hood or the t runk lid is
open . T his symbo l also shows which door or
lid has no t been closed
~ fig. 13 .
As soon as the doo r, the hood and the trunk
lid a re closed proper ly, the door and trunk lid
warning turns off and the selected d river in
format ion sys tem func tion s are d isplayed
again .
Page 28 of 316

26 Driver information d isplay
program. The fuel economy messages turn off
automatically after a certain per iod of t ime .
.,. To turn a fuel economy message off imme-
dia tely after it appears, press the
I RESE T I
button Q page 24 , fig . 17 @, or
.,. Press the funct ion selection switch
~ page 24 , fig. 17@.
(D Tips
-Once you have turned a fuel economy
message off, it will only appear again af
ter you turn the ignition on again.
- The fuel economy messages are not dis
played in every instance, but rather in in
tervals over a period of time.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
T he Malfunction Indicator Lamp (MIL) ¢4 in
the instrument cluster
Q page 14, fig. 8 is
part o f the On-Board Diagnostic (OBD II) sys
tem.
T he warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized .
T his indicates that the MIL is working proper
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv
ing, a malfunction may exist in the engine sys
tem. If the light illuminates, the catalytic con
verter could be damaged.
Continue driving
with reduced power (avoid
ing sustained high speeds and/or rapid accel
erat ions) and have the condition corrected .
Contact your author ized A udi dealer.
If the light illuminates, the electronic speed limiter may also be malfunctioning. For more
information
Q page 2 7, Electronic speed
limiter .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
Qpage231 .
On-Board Diagnostics
Fig. 21 Location of Data Li nk Conn ecto r (DLC)
On-Board Diagnostics monitors the compo
nents of your emission control system . Each
monitored component in your engine system
has been ass igned a code . In case of a mal
function, the component will be identified
and the fault stored as a code in the control
module memo ry.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery sys
tem .
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed
Q page 231.
In order to make an accurate diagnosis , the
stored data can only be displayed using spe
cial diagnostic equipment (generic scan tool
f or OBD).
In order to connect the spec ia l diagnostic
equipment , push the plug into the Data Link
Connector (DLC). Th e DLC is located to the
right of the hood release
Qfig. 21.
Your authorized Audi dea ler or qualified work
shop can interpret the code and perform the
necessary repair.
~ ARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
malfunctions, which can increase the risk
of a collision!
-
Page 31 of 316

warning goes out after about 5 seconds, but it
can be brought up at any time by pressing the
ISETI button again.
Usu ally, you can still drive to the nex t dea ler
ship. Turn off all but the most necessary elec
trica l consumers, since these drain the vehi
cle's battery.
@ Note
If the . warning symbo l (coolant system
malfunction) also lights up on the instru
ment panel during the trip¢
page 30,
then you have to stop immediately and
turn off the eng ine. The coolant pump is
not working anymore -danger of damage
to the eng ine!
BRAKE/( (j)) Brake system malfunction
A malfunction in the brake system must be
repaired as soon as possible .
If the warn ing /indicator light ~ (USA
models)/ . (Canada mode ls) in the instru
ment cluster flashes, there is a brake system
malfunct ion . A dr iver message appears as
well to explain the malfunction in mo re de
tail. The d rive r warning goes out after about 5
seconds, b ut i t can be brought up at any time
by pressing the
I SE T! button aga in .
Stop vehicle and check brake fluid l evel
~ Stop the vehicle.
~ Check the brak e fluid leve l¢ page 242.
~ Seek professiona l assistance if necessa ry.
Warning! Fault in brake system. Contact
workshop
~ Drive carefu lly to the nearest authorized
Audi dealer or other qualified workshop and
have the malfunct ion correc ted ¢
&-
Par king brake system fault! See owner's
manual
~ If t his symbol appears when t he ve hicle is
stationary or afte r the ign ition is turned on,
chec k to see if the parking bra ke can be re
l eased. Drive to an authorized Audi dealer or
other qualified workshop as soon as possi-
Dri ver information di spla y 29
ble and have the malfunction cor rected . If
the parki ng brake cannot be opened, then
take it to an expert at an authorized Audi
dea ler.
~ If the symbo l appears while you are driving,
it is possible that the traction co ntrol o r the
emerge ncy brake has malfunctioned .
It is
possible that th e parking b rake cannot be
app lied.
It is also possible t hat the parking
b ra ke cannot be re le ased after i t has been
app lied . D rive to an authorized Aud i dea ler
or ot her qualified workshop to have t he mal
function corrected.
If t he ABS system malfu nctions, the ABS
warning/indicator light illumina tes together
with the brake system ma lfunction wa rning/
indicator light ¢.& .
A WARNING
-A lways observe the warn ings in
¢ page 226, Engine compartment, be
fore opening the hood and check ing the
bra ke fluid.
- Driving with low brake fluid is a safety
hazard . Stop the car a nd get professiona l
assistance .
-USA models: If th e ~ warning light
a nd the
B warning light come on to
gethe r, the rear whee ls cou ld lock up
fi rst under hard bra king. Rear wheel lock
up can ca use loss of vehicle co ntrol and
an ac cident. Have yo ur vehicle rep aire d
immediate ly by yo ur authorize d Au di
dea ler o r a qua lified wor kshop. Drive
slowly and avo id sudden, hard brake ap
plications.
- Canada models: If the brake warning
light . and the ABS warning light
El]
come on together, the rear wheels could
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
control and an acc ident. Have yo ur vehi
cle repaired immed iately by your author
i z ed A udi dealer o r a q ual ified wor kshop.
Drive s low ly and avoid s udden, hard
brake applications .
Page 32 of 316

30 Driver in formation d isplay
...L Engine cooling system malfunction
A malfunction in the engine cooling system
must be repaired as soon as possible .
If the . symbol flashes in the display, either
t he eng ine cool ant
temperature is too h igh or
the eng ine coolant
level is too low . A dr iver
message appears as well to explain the mal
function in more detail. The d rive r warning
goes out afte r about 5 seconds, but it ca n be
b rought up a t any time by p ress ing the
!SE TI
button again.
Turn off engine and ch eck coolant l evel
• Pull off the road .
• Stop the vehicle .
• Turn off the engine.
• Check coo lant level¢
page 240.
• Add coolant if ne cessa ry ¢ page 241 .
• Co ntin ue d riving only after the eng ine cool
ant warn ing/ indicato r light goes o ut.
• Contact your a uthorized Audi dea ler for as-
sistance if necessary.
If the engine coolant level is co rrec t, then the
radia tor fan may be the cause o f the malf unc
tion .
A WARNING
-If your veh icle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn off the engi ne and turn on the hazard
wa rning lights ¢
page 52, Emergency
flash ers.
-
- Never open the hood if you see or hea r
steam o r coolant esca ping from the en
gine compa rtme nt - you risk being s cald
ed. Wait until you can no longe r see or
hear steam or coo lant es caping.
- T he e ngine compartmen t of a ny veh icle
is a dan gerous area. Before you perform
any wor k in the engine compartment,
t ur n of the engine and allow it to coo l.
Follow the wa rning stickers ¢
page 226,
Engine compartment.
(D Note
Do not continue driv ing if the . symbo l
ill um inates . There is a mal function in the
engine cooling system -you could damage
your engine.
"l:::r. Engine oil pressure malfunction
T he red engine oil pressure warning symbol
requires immediate service or repair. Driving with a low
oil pressure indication is likely to
cause severe engine damage .
If the . symbo l on the disp lay flashes, the
engine oil pressure is too low. A driver mes
sage appears as we ll to exp la in the malfunc
t io n in more detail. The dr iver warning goes
o ut afte r abo ut 5 seconds , but it can be
brought up at any t ime by p ressing the
~ 1s =ET= I
button ag ain.
Turn off engin e! O il pressure too low
• Stop the vehicle.
• Turn the engine off.
• Chec k the engine o il level ¢
page 238 .
• Contact yo ur au thorized Aud i deale r for as-
sistance if necessa ry.
Eng ine oil level too low
If the engine oil level is too low, add engine
o il
¢page 238.
Engine oil leve l correct
If the symbol . flashes even tho ugh the en
gine oil leve l is correct, please contact your
nearest authori zed Aud i Dea ler for assistance.
Do not continue dr iving . Do not leave the en
gine running
idle, either .
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low eng ine oil lev
e l. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals, preferably each time you refuel, and always before going on a long trip .
Page 33 of 316

-The yellow oil level warning indication
II requires oil refill or workshop serv
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil
level warning
11-By then, your engine
may already have suffered serious dam
age .
~ . Fill engine oil now
WARNING: Please add oil immediately
If the . symbol lights up, then the o il has to
be re plenished r ight now ~
page 238 .
~- Steering malfunction
If there is a malfunction in the electronic
steering column lock, the steering cannot b e
unloc ked .
If the . symbol i n the display blinks , th ere
i s a malfunction in the electronic steer ing col
u m n lock . A driver message a ppears as well to
e xplain t he malfu nction in m ore deta il. The
d river war ning goes ou t a fter abou t
5 se c
on ds, but it can be brough t up at an y time by
p ress ing t he
ISE TI but ton again.
Steering defective! Do not drive vehicle!
.,. Co ntact your nearest authorized Audi deal
er .
.,. Do
not tow yo ur vehicle .
A WARNING
Your vehicle must not b e towe d in th e
eve nt of a m alfu nction in the ele ctronic
s t eerin g colum n lo ck bec ause i t ca n not be
steered due to the l ocked steering . If it is
towed with the stee ring loc ked, t here is
the risk of an accident.
© -Ignition lock malfunction
A mal function in the ignition lock mus t be re
paired immediately .
If th e. symbol in the d isp lay blink s, there
i s a ma lfunc tion in the elec troni c ignition lo ck.
Driver information display 31
A dr iver message appea rs as we ll to ex plain
t h e malfunction i n mo re deta il. The dr iver
warning goes out after a bout 5 seconds, b ut it
can be b roug ht up at any time by pressing the
ISE TI b utt on again.
Ignition lock defective. Contact dealer!
.,. Do not tu rn th e e ngine o ff.
.,. Drive imme diate ly to an a uthor ized A udi
dea le r to have t he mal funct io n corrected .
If there is a mal fun ctio n in t he ele ct ro nic igni
tio n loc k, the igni tion can not b e turne d off.
Drive immediate ly to an au tho riz e d se rvice fa
c ili ty to have t he cause of t he malfunct ion cor
r ected .
On vehicle s wi th Conven ien ce key* , the eng ine
s h ould not b e swi tc h ed off usin g th e S tart/
Stop button because t he engine cannot be
started again afte r th e ignit io n has been
switc hed off.
· Yellow symbols
A yellow symbol me ans WA RNING .
Fig. 24 Display: Yellow wa rning symbo l
N ..,
I
Yellow symbo ls ind icate a prior ity 2 malfunc
tion -Wa rning!
When a yellow warn ing symbol appears,
one
warning to ne sounds . A d river message ap
p ears as well to exp lai n the ma lfu nction in
m ore d etail. T he d rive r war ning goes out aft er
abo ut 5 seconds, but it ca n be broug ht up a t
any ti me by press ing t he
ISE TI button again .
Check the function displayed as s oon as possi
ble. The yellow symbol will not go out again
u nti l th e re ason fo r the mal func tion has bee n
cor rected.