ignition AUDI Q5 2013 Manual Online

238 Checking and filling
Checking the engine oil level
Fig. 197 Disp lay: Oi l level indicator
Read oil level
• Park your vehicle so that it is horizontally
level.
.. Shut the engine off when it is at operating
temperature.
.. Switch only the ignition back on.
• Wait approx. two minutes.
> Select: ICARI function button> Oil level. Or
> Select: ICARI function button> Car sys-
tems *
control button > Servicing & checks >
Oil level.
• Read the oil leve l in the radio or MMI* Dis­
play
r::;:, fig. 197. Add engine oil if the bar of
the oil level indicator is near "Min"
r::;:,page 238.
The oil level needs to be checked at regular in­
tervals . The best times to do this are whenev­
er you refuel and prior to long trips .
Depending on the way the vehicle is driven
and the operating conditions, oil consumption
can be up to a 1/2 quart per 600 miles (0.5
li­
ter per 1,000 km). Consumption may be high­
er within the first 3,000 miles (5,000 km).
@ Tips
The oil level indicator in the radio or MMI*
Display is only an information display. If
the oil level is too low, a minimum oil
warning appears in the instrument cluster.
Add oil
r::;:, page 238. If the hood has been
opened, the current oil level is shown in
the instrument cluster the next time the
ignition is switched on.
Adding engin e oil 't:::r.
Fig. 198 En gine compart men t: cover on the engine oil
fille r neck
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS
r::;:, .&. in Working in the engine compart­
ment on page 233.
"' Unscrew the cap 't=1'l to the engine oil filling
hole ¢
fig. 198, r::;:, page 235, fig. 196 .
• Carefully top off with the appropriate oil in
0.5 liter doses.
.. Check the oil level again after two minutes
r::;:,page238 .
"'Top off the oil, if necessary.
"' Screw the cap back on the filling hole.
A WARNING
=
-While topping off, the oil must not come
in contact with hot engine parts - fire
hazard!
- The oil filler cap must be properly se­
cured to prevent oil from being sprayed
on the hot engine and exhaust system
when the engine is running -fire hazard!
- If your skin has come in contact with the
engine oil, you must subsequently
cleanse it thoroughly.
(D Note
- Check the oil level using the radio or the
MMI*. If the message
Please reduce oil
level
appears, contact your authorized
Audi dealer or other qualified workshop
to have excess oil extrac ted if necessary.
-Audi does not recommend the use of oil
additives. They may damage the engine ..,..

240 Checking and filling
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro­
tects the engine from freezing in the winter .
The cooling system is sealed and generally re­
quires little attention.
The cooling system has been filled at the fac­
tory with a permanent coolant which does not need to be changed. The coolant consists of a
mixture of water and the manufacturer's gly­
col-based coolant additive Gl3 ant ifreeze
with anticorros ion add itives (SO% for USA
models; 60% for Canadian models). This mix­
ture both assures the necessary frost protec­
tion and protects metal components in the
engine's cooling system from corrosion and
scaling. It also raises the boiling point of the
coolant.
Do not reduce the concentration of the coo l­
ant in the summer by adding plain water .
The
proportion of coolant additive must be at
least 50% but not more than 60%
to main­
tain antifreeze protection and cooling efficien­
cy. If the coolant frost protection is too low,
the coolant could freeze and damage the veh i­
cle heating and engine cooling system .
For year-round driving, antifreeze is added at
the factory for temperatures down to:
- - 31 °F ( - 35°() USA
- - 40°F ( - 40°() Canada .
A WARNING
Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c:> &. in Working in the engine
compartment on page 233.
- Before winter sets in, have the coolant
checked to see if the coolant addit ive in
your vehicle is sufficient to meet the cli­
mate cond itions. This is especially impor­
tant if you live in a region where the w in- ter
is extreme ly cold . If necessary, in­
crease the proportion of coolant additive
to 60%.
- When adding coolant additive to your
cooling system, remember:
- We recommend using only coolant ad­
ditive Gl2++ or Gl3 for your vehicle.
This coolant additive is available at au­
thorized Audi dealers. Other types of
antifreeze can significantly reduce cor­
rosion protection. The resulting corro ­
sion can ca use a loss of coolant and se­
rious engine damage.
- Do not add any type of radiator leak seal ­
ant to your vehicle's engine coolant .
Add ing radiator repair fluid may adverse­
ly affect the function and performance of
your cooling system and could result in
damage not covered by your New Vehicle
Limited Warranty.
Checking the engine coolant level
The engine coolant level can be checked with
a quick glance .
Fig. 199 Engine compartment : cover on t he coolant
expansion tank
Before you check anyth ing in the engine com­
partment,
always read and heed all WARN­
INGS c:> &. in Working in the engine compart­
ment on page 233 .
.. Park your vehicle on a level surface .
.. Turn off the ignition .
.. Read the engine coolant level from the
coolant expansion tank
c:> fig. 199,
c:> page 235, fig. 196 . With a cold engine,
the coolant level should be between the
"MIN" and "MAX" markings. When the

24 2 Ch ecking and filling
-If you drain the coolant, it must be
caught and safely stored in a p roper
conta iner clearly marked "poison".
(D Note
- Coolant pollutes the env ironment and
could cause an engine fire . Excess coo l-
ant will be forced out through the pres­
sure relief valve in the cap when the en­
gine becomes hot.
- If, in an emergency, only water can be
added , the correct ratio between water
and antifreeze¢
page 240 must be re­
stored as soon as possible .
@ For the sake of the environment
Drained coolant should not be reused. Al­
ways dispose of used coolant while observ­ ing all environmental regulations.
Radiator fan
The radiator fan switches on automatically by
itself
The radiator fan is driven by the engine via the
V-be lt . The viscous clutch regulates the speed
of the fan accord ing to t he temperature of the
coolant.
An auxiliary electric radiator fan* switches on
a nd off depending on coolant temperature
and other ve hicle operating conditions.
After you switch the engine off, the auxiliary
fan can cont inue running for up to 10 minutes
- even with the ignition off. It can even switch
on again later by itself¢&. , if
- the temperature of the engine coolant rises
due to the heat build-up from the engine in
the engine compartment, or
- the engine compartment heats up because
the veh icle is parked in intense sunlight.
_&. WARNING
- To reduce the r isk of personal injury nev­
er to uch the radiator fa n. -
The a uxiliary electric fan is temperat ure
controlled and can switch on suddenly
even when the engine is not running.
- The auxiliary radiator fan switches on a u­
tomatically when the engine coolant reaches a certai n temperature and will
continue to ru n until the coolant temper­
ature drops.
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
F ig. 2 00 Engine compart men t: cover on t he brake fluid
reservoir
Befo re you check anyth ing in the engine com­
partment,
alway s read and he ed all WARN­
INGS c::> ,&. in Working in the engine compart­
ment on page 233.
.,. Read the brake fluid level from the b rake
fluid reservoir
c::> fig. 200, c::> page 235,
fig. 196.
The brake fl uid level m ust be be­
tween the "MIN" and "MAX" markings.
T he bra ke fluid reservo ir is located at the rear
part ition o f the e ngine compartment on the
left s ide
c::> page 235.
The fluid level may drop slightly afte r some
t ime due to the a utomatic adjustment of the
brake pads. This is not cause for a larm .
If the brake fl uid level falls
considerably be­
low the
"MIN" mar k, the brake war ning/ indi­
cator light ( U.S. models:
1111 , Canadian
models :. will come on
c::> page 18 and
c::>page 29. Do not con tinue to operate the ve-
hicle . The comp lete brake system should be ..,.

244 Checking and filling
Vehicles not driven for long periods
If you do not drive you r vehicle over a pe riod
of severa l days or weeks, electrical compo­
nents are gradually cut back or switched off.
This reduces energy consumption and main­
tains starting capability over a longer period
¢page 203.
Take into consideration that when yo u un lock
your vehicle, some convenience functions, such as the interior lights or the power seat
adjustment, may not be available. The con­
venience funct ions w ill be available again
when you turn on the ignition and start the
engine .
Winter operation
During the winter months, battery capacity
tends to decrease as temperatures drop . This
is because more power is also consumed while
start ing, and the headl ights, rear window de­
fogger, etc., are used more often .
Avoid unnecessary power consumption, par­
ticularly in city traffic or when traveling only
short distances . Let your authorized Audi
dealer check the capacity of the vehicle bat­
tery before winter sets in¢
page 245. A well
cha rged battery w ill not only prevent starting
prob lems when the weather is cold , but will
a lso last longer .
Working on the battery
Be especially careful when working on or near
the battery.
The battery is located in the luggage compart­
ment under the floor. Before you check any­
thing in the luggage compartment,
read and
heed all WARNINGS
¢ _&..
Hybr id drive*: you can find impo rtant informa­
tion about the high voltage battery under
¢page 97 .
Always heed the safety warnings , when work­
ing on the vehicle battery or the vehicle elec ­
trical system to prevent injury.
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM­ BOLS and safety precaution s when working
on the battery.
@) Always wear eye protection .
I>. Battery acid contains sulfuric acid_-Al­
~ ways wear gloves and eye protection.
~ No
\!=51 -sparks
-flames
-smoking.
A When a battery is charged, it produces
~ hydrogen gas which is explosive and
could cause personal injury.
/G Always keep the battery well out of
V!!JI reach of children.
A WARNING "--
Whenever working on the battery or on
the electrical system, there is the risk of
in jury, accident and even fi re. Read and
heed the following WARNINGS :
- Always wear eye protection. Do not let
battery ac id or any lead particles get on
your skin or clothing. Shield your eyes .
Exp losive gases can cause blindness or
other injury .
- Ba ttery acid contains sulfuric acid. Sulfu­
ric acid can ca use blindness and severe
burns .
- Always wear gloves and eye protection .
Do not tilt the battery because acid
could leak out of the ventilat ion open­
i ngs.
- If you get battery ac id in your eyes or
on your skin, immediately rinse with
cold water fo r several minutes and get
med ical attention .
-If you should ingest any battery acid,
seek medical attention immediately.
- Do not expose the battery to an open
flame, electr ic sparks or an open light.
- Do not smoke.
-
1
I

-Do not interchange the positive and neg­
ative cables .
- When working on the battery , be sure
not to short-circuit the terminals with
tools or other metal objects. This would cause the battery to heat up very quickly,
which could lead to damage or explosion
and personal injury.
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury .
- Always keep the battery well out of the
reach of children .
- Before work is done on the electrical sys­
tem, disconnect the negative ground ca ­
ble .
- Before performing any work on the elec ­
trical system , switch off the engine and
ignition as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected. If you are just go­
ing to replace a light bulb, then it is
enough to switch off the lights.
- Before disconnecting the battery , switch
off the anti-theft alarm system! Other­
wise you will set off the alarm.
- When disconnecting the battery, first
disconnect the negative cable and then
the positive cable.
- Before reconnecting the battery, make
sure all electrical consumers are switch­
ed off. Reconnect the positive cable first
and then the negative cable. Never inter­
change the cables - this could start a fire!
- Never charge a fro zen or a thawed-out
battery. It could explode! If a battery has
frozen, then it must be replaced. A dis­
charged battery can freeze over at 32°F
(OOC) .
-Make sure the vent hose is always attach­
ed to the opening on the side of the bat ­
tery.
- Never use batteries which are damaged.
There is the danger of an explosion! Al­
ways replace a damaged battery.
Checking and filling 245
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related ac­ cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc ­
tive problems . Wash hands after han­
dling.
Q) Note
- Do not disconnect the vehicle battery
when the ignition is switched on or when
the engine is running, otherwise , you will
damage electronic components in the
electrical system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect the battery from "freezing", oth­
erwise it will be damaged and will then
have to be replaced.
Battery charging
Starting the engine requires a well charged
battery.
Fig. 201 Engin e compart ment: Co nn ectors for charger
and j umper cab les
Always read and heed all WARNINGS below
¢ .&. and ¢,&. in Working on the battery on
page 244.
~ Hybrid drive*: read the important informa­
tion concerning a dead high voltage battery
under
¢ page 105.
~ Turn off the ignition and all electrical con­
sumers.
~ Make sur e the area is well ventilated when
you charge the battery . ..,.

When the malfunction indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of rea­
sons, including the installation of replace­
ment or alternate tires or whee ls on the veh i­
cle that prevent the TPMS from funct io ni ng
p roperly . Always check the T PMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly .
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 208 Display : underinflatio n warning
Using the ABS sensors, the tire pressure moni­
toring system compares the t ire tread circum­
ference and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indica ted in the instru­
ment clus ter with a
IE warning symbol and a
message ¢
fig. 208. The driver message in the
display goes out after 5 seconds. The driver message can be displayed again by pressing
the
! SET ! button. If only one tire is affected,
the display will indicate its pos ition.
The ti re press ure monitoring system must be
reset via radio or MMI* each time the pres­
sures are adjusted (e.g . when switching be ­
tween partia l and full load pressure) or after
changing or replacing a t ire on your vehicle
¢
page 268 . The TPMS indicator only moni­
tors the tire pressure that you have prev iously
Tire s an d wheel s 267
stored . You can find the recommended t ire
pressures for yo ur vehicle on the label on driv­
er's side B-pillar ¢
page 252.
Tire tread circum ference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire p ress ure in one or more tires is too
low,
- t he t ire has structural damage,
- the t ire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
¢ page 268.
Warning symbo ls
IE Loss of pressure in at least one tire¢.&,.
Check the tire or tires and replace or repa ir if
necessary. The
IE indicato r light in the inst ru­
ment cluster a lso illuminates
c::!;> page 14.
Check/correct the press ures of all fou r tires
and reset TPMS via radio o r MMI*.
119;~, (T ir e Pressure Mon itoring System) Tire
pre ssure: Syst em malfun ction!.
If 11Nlf:1 appears afte r switching the ignition
on or while driving and the
IE indicator light
i n the instrument cluster blinks fo r approx i­
mately one minute and then stays on, there is
a system malf unct ion.
Attempt to store the correct tire pressure
¢ page 268 . If the ind icator light does not
tu rn off o r if it turns on sho rtly the reafter, im­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or au thorized repair faci lity to
have the malfunc tion corrected .
A WARNING
-=
-If the tire pressure indicator appears in
the instrument cluster display, one or
more of your t ires is significant ly under­
inflated. Reduce your speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire p ressure to the prope r pres­
sure as indica ted on the vehicle's tire
pressu re labe l
¢page 252. Driving on a
significantly under-i nflated tire causes
•
•

268 Tires and wheels
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­ paved roads), the pressure monitor indi­
cator may be delayed.
-Ask your authorized Audi dealer if run­ flat tires may be used on your vehicle.
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your vehicle or accidents
could also result.
@ Tips
- The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with the "AO" or "RO" identification on the
tire sidewall¢
page 259. We recom­
mend using these tires.
Reset tire pressure monitoring system
Applies to vehicles: with tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
radio or MMI*.
11> Befo re resetting the TPMS, the current pres­
sures of all four tires must correspond to
the specified values. Adjust the tire pressure
and reset the pressure in the tire pressure
monitoring system according to the load
you are carry ing
¢page 252.
11> Turn on the ignition.
11> Select: ICARI function button > Tire pres­
sure monitoring
> Store now . Or
i,. Select: ICARI function button > Car sys­
tems *
control button > Servicing & checks >
Tire pressure monitoring > Store tire pres­
sures.
@ Tips
Do not store the tire pressure if there are
snow chains on the tire.

282 Fuses and bulbs
I
-
No. Consumer
2 Wi-Fi
3 MMI/Radio
4 Instrument cluster
5 Gateway (instrument cluster
control
module)
6 Ignition lock
7 Light switch
8 Climate control system blower
9 Steering column lock
10 Climate control system
11 Terminal 30 diagnostic connec-
tor
12 Steering column switch module
Right luggage compartment fuse
assignment
Amps
5
5/20
5
5
5 5
40
5
10
10
5
Fig. 226 Right luggage compartment: fuse panel with
plastic cl ip
No. Consumer Amps
Fuse panel
@ (black)
1 Luggage compartment lid con-
30
trol module
2 Trailer control module 15
3 Trailer control module 20
4 Trailer control module
20
-No. Consumer Amps
5 Electromechanical
parking
5
brake
•
6 Electronic damping control 15
7 Electromechanical parking
30
brake
8 Rear exterior lighting 30
9 quattro Sport
35
10 Rear exterior lighting 30
11 Vehicle electrical system control
20
module
12 Terminal 30
5
Fuse panel c (brown)
1 Luggage compartment lid con-
30
trol module
2 12-volt socket, cigarette lighter
DCDC converter path 1 or high
3 voltage battery blower (hybrid 40
drive)
4 DCDC
converter path 2, DSP
30
amplifier, radio
7 Electromechanical
parking
30
brake
Right front door (window regu-
9 later, central locking, mirror, 30
switch, lighting)
11 Rear
right door (window regula-
30
tor, switch, lighting)
12 Cell phone prep 5
Fuse panel© (black)
1 Right front seat heating
15
2 Automatic dimming rearview
5
mirror
3 Instrument panel terminal 30
4 MMI 7,5
Rearview camera
Rear window heater
8 Rear Seat Entertainment
12 High voltage battery (hybrid
drive)

2 90 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 292. This sec ­
tion provides general information, notes and restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker.
Fig. 236 Veh icle Ide ntific atio n Number (VlN) p late: lo ­
cation on driver 's sid e das h panel
Fig. 237 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 236. You can also display the Vehicle
Identification Number of your vehicle in the
radio or in the MM!*. Select
! CAR ! function
button>
Vehicle ID number (VIN) or !CARI
function button> Car systems* control but­
ton >
Servicing & checks > VIN number . The
vehicle identification label
is located in the luggage compartment above
the compartment for the vehicle tools.
The label¢
fig. 23 7 shows the follow ing vehi­
cle data :
(D Production control No.
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
t ime the vehicle was manufactured . You can
find this sticker on the left door jamb .
It
shows the month and year of production and
the vehicle ident ification number of your vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus fu ll fuel tank,
oi l and coolant, plus maximum load , which in­
cludes passenger weight (150 lbs/68 kg per
Ill>

Index 301
-----------------------------------.......
Automatic Shift Lock (ASL) . ... .. .. .. . 124
Automatic transmission .......... .... 123
Automatic S hift Lock (ASL) . .. .. .. .. . 124
Driving .. .. ............. .. .. .. ... 125
E mergency mode ......... .. .. .. .. . 128
E me rgency release . . . . . . . . . . . . . . . . . 128
Hill descent control .... ... .. .. .. .. . 126
Kick -down . ..... ...... ... .. .. .. ... 127
Manual sh ift program ..... .. .. .. .. . 127
Removal lock (ignition key) . .. .. .. .. .. 83
Selector lever ......... ...... .... .. 123
Shift buttons .... .. ...... .. .. .. .. . 127
Automatic wipe/wash system . . . . . . . . . . 54
Auto Safety Hotline ........ .. .. .. .. . 146
AUTO (climate contro l) . . . . . . . . . . . . . . . . 80
Average speed . . . . . . . . . . . . . . . . . . . . . . . 23
Avoid damag ing the vehicle ...... . ... . 206
B
Bass box .. ............ ...... .... .. 270
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Battery locat ion inside the luggage com-
partment .. ............. .... .. .. . 244
C harging . . . . . . . . . . . . . . . . . . . . 105 , 245
Important war nings when working on
the battery . . . . . . . . . . . . . . . . . . . . . . . 244
Jump starting ............... ... ... 284
L ow . .. .. .. ................. .. .. . 203
Replacing the batte ry ..... .. .. .. .. . 246
State of charge . .. ..... ... .. .. .. ... 203
Voltage .... .... ...... ... .. .. .. .... 34
Winter operation . ..... ... .. .. .. .. . 243
Working on the battery . . . . . . . . . . . . . 244
B efore driving ............. .... .. .. . 139
Bio-ethanol (Fuel) .... ...... .. .. .. .. . 229
Blended gasoline ... .... ... .. .. .. ... 228
B lower (climate control) . . . . . . . . . . . . . . . 80
Body cav ity sealing ......... .. .. .. .. . 222
B ooster seats .. .. .. .... ... .. .. .... . 186
Brake flu id
Changing the brake flu id .... ... ... .. 243
C hec kin g the bra ke fluid level . .. .. .. . 242
Reservoir .. .. ........... .. .. .. ... 24 2
Wha t is the cor rect brake flu id leve l? . . 24 2
What should I do if the brake flu id warn -
ing light comes on? .... ... .. .. .. .. . 242 Brake system .
..... ... .. .. ..... ... .. 242
Anti- lock b rake system . . . . . . . . . . . . . . 17
Brake assist system .. .. ..... ... .. .. 197
Brake booster .. .. ................. 200
Brake fluid .. .. .. .... ............. 242
B rake fluid specifications fo r refill and re ­
placeme nt . . . . . . . . . . . . . . . . . . . . . . . 243
B ra ke light defective . . . . . . . . . . . . . . . . 33
B ra ke pads .. .. .. .. . .............. 205
El ec tromechan ical par king br ake . .. .. . 88
General informa tion . ... .... ... .. .. 2 00
How does moist ure or road salt affect the
brakes? ... .. .. .. .. . ... ...... ... .. 200
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 29
Warning/ind icator lights ............ . 18
Wor n brake pads symbol . . . . . . . . . . . . . 33
Braking guard . . . . . . . . . . . . . . . . . 107, 113
Messages . . . . . . . . . . . . . . . . . . . . . . . . 114
Settings .. .. .. .. .. ............... 114
Switching on and off ........... .. .. 114
B reak-in per iod .. .. .. . .............. 205
B rake pads .. .... .. . .. .. ..... ... .. 205
Tires ... .. .. .... .. . .. .. ..... ... .. 205
B reakove rangle . .. .... ........... .. 209
Bu lbs ........ .. ...... ............. 283
C
Californ ia Proposition 65 Warning ... .. 234
Battery spec ific . . . . . . . . . . . . . . . . . . . 245
C ap aci ties .. .. .. .. .... ........... .. 292
Car care .......... .. ..... .......... 216
E xterior . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Inte rio r ... .. .. .. .. ............... 223
Plast ic and vinyl .. .... ............. 220
Cargo a rea
refer to Loading the l uggage compart -
ment . ...... .. .... .......... ..... 145
Cargo floor . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cata lytic converter . .... ......... .... 2 06
Center armrest Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . 66
Storage compa rtment .. .. .. ... ... .. . 66
Certification .. .. .. .. ............... 298
Changi ng
A flat t ire ... .... .. . .. .. ..... ... .. 274
A whee l ... .. .... .. . .. .. ..... ... .. 274
Engine oi l ... .... .. . .. .. ..... ... .. 239
•
•