key AUDI Q5 2017 Owner's Guide

CD
CD
.... N ,-... N .... 0 0 C<'. 00
electrical equipment s uch as exterior lights
will switch off as well when that happens.
Switching engine off
A pp lies to: ve hicles with Conve nien ce key
~ Bring your vehicle to a complete stop.
~ Move the selector lever to the P or N position.
~ Press the I STAR T ENGINE ST OPI button
¢ page 84, fig. 101.
Ste ering lock
The steering locks when you turn the engine off
using the
! S TART ENGINE STOPI button and
open the dr iver's door. The locked steering helps
prevent vehicle theft.
Emer gency off
If necessary, the engine can be switched off with
the selector lever in the R or D/S position. The
engine stops if you press and ho ld the
I START ENGINE STOPI button at speeds below
6 mph (10 km/h) and press the brake pedal.
A WARNING
- Never turn off the engine before the veh icle
has come to a comp lete stop. The fu ll func­
t ion of the brake booster and the power
steering is no t gua ranteed. You must use
more fo rce to turn or brake i f necessary. Be­
cause you cannot steer and b rake as you
usually wou ld, this could lead to crashes
and ser ious injuries.
- For safety reasons, you should a lways park
your vehicle with the selector lever in P .
Otherwise, the vehicle could inadvertently
roll away.
- The radiator fan can continue to run for up
to 10 m inutes even after you have turned
off the engine and removed the ignition key.
The radiator fan can also turn on again if the engine coolant heats up because of intense
sunlight or heat bui ld-up in the engine com­
partment.
- Always take the key with you whenever you
leave you r vehicle. Othe rw ise, the engine
c ou ld be started o r electrical equ ipme nt
D riv ing
such as the power windows could be operat­
ed. This can lead to ser ious injury.
- Never leave chi ldren or persons requiring as­
sistance unattended in the vehicle. The
doors can be locked using the remote trans­ mitter, preventing people from escaping
from the vehicle on their own in the event of
a n emergency. Depending on the time of
year, people ins ide the veh icle can be ex­
posed to very high o r very low tempera­
tures.
0 Note
If the engine has been under heavy load for
an extended pe riod, heat bu ilds up in the en­
g ine compartment afte r the engine is switch­
ed off -there is a ris k of damaging the engine.
A llow the engine to run at id le for about two
minutes before switching it off.
Driver messages
Ignition i s on
This message appears and a warning tone sounds
if you open the drive r's door when the ig nition is
swi tched on.
No k ey id ent ified
This message appears when the
I START ENGINE STOP !* button is pressed if there
is no master key inside the vehicle or if the sys­
tem does not recognize it. For example, the mas­
ter key cannot be recognized if it is covered by an
obje ct (e.g. al uminum brief case) which
screens
the radio s ignal. Elec tronic devices such as ce ll
phones can a lso interfere with the radio signal.
Pre ss brake p edal to start en g ine
This message appears if you do not press the
brake pedal to start the engine.
S hift to N or P to start en gine
This message appears when attempting to start
the engine if the se lector lever for the automatic
transm ission is not in the P or N position. The en­
gine can on ly be started with the se lector in
these positions.
Ill-
85

Driving
!I Is the key in the vehicle ?
This message appears in a veh icle with Conven­
ience key* if the master key is removed from the
ve hicle w ith the engine r unning.
If the maste r
key is no longer in the vehicle, you cannot switch
on the ignition after stopping the engine and you
also cannot start the eng ine again. Moreover, you
cannot lock the veh icle from the outside with the
key.
Shift to P otherw ise vehicle can roll awa y. Door s
do not lo ck if le ver i s not in P.
This message appea rs fo r sa fe ty reasons a long
with a warning signal.
It appears i f the se lector
lever for the automatic transmission is not in the
P posit ion when switching off the ignition. Move
the selector lever to the P position, otherwise the
vehicle is not secured aga inst rolling away. You
also cannot lock the vehicle using the locking
button* on the door handle or using the remote
key .
Turn off ignition befo re lea ving car
This message appears if the driver's door is
opened while the ignit ion is switched on. A lways
switch off the ignition if you are leaving the vehi­
cle . See also
c::> page 90.
Turn off ignition before lea ving car. Batte ry is
discha rging
This message appea rs if the d river's doo r is
opened while the ignition is sw itched on. A lways
switch off the ignition if you are leaving the vehi­
cle . See also
c::> page 90.
Shift to P and turn off ignition, otherwi se vehi­
cle can roll awa y
This message appea rs if the d river's door is
ope ned while t he igni tion is switched on and the
selec to r l ever is not in the P posi tion. Shift t he
selector lever in to the P position and switch off
the ignition when you exit the vehicle . Otherwise
the vehicle cou ld roll. See also¢
page 90.
Convenien ce key defective! Use ignition lock
This message appea rs if the eng ine must be
started or stopped using the ignit io n key and no t
t he !STAR T
ENGINE ST OPI* b utton .
86
Electromechanical
parking brake
Operation
The electromechanical parking brake replaces
t he hand brake.
Fig. 102 Center co nsole : Pa rk ing brake
.. Pull on the switch (®) c::> fig. 102 to apply the
park ing brake. The indicator lights in the switch
and . (USA models)/ . (Canada models) in
the inst rument cluste r illuminat e.
.. With the ignition switched on, step on the
brake pedal or the ac celerator peda l and press
t he swi tch(®) at the same time to release the
p arking brake . The indicator lights in the switch
and . (USA models)/ . (Canada models) in
the instrument cluster go out .
Y our vehicle is equipped wi th an ele ctromechan i­
ca l park ing brake . The parking brake is desig ned
to prevent the vehicle from ro lling unintentional­
ly and replaces the hand b rake.
In add ition to the no rmal functions of a trad i­
tiona l hand b rake, the e lectromechanical parking
brake provides various convenience and safety
funct ions .
When starting from rest
-The integra l st art ing ass ist helps yo u when
dr iving by automati ca lly re leas ing t he pa rking
brake
c::> page 87, Starting from rest .
-When starting on inclines, the starti ng assis t
prevents the vehicle from unintentionally ro ll­
ing back. The brak ing force of the park ing brake
is not re leased unti l su fficient dr iving force has
been bu ilt up at the whee ls. ..,.

CD
CD
.... N ,-... N .... 0 0 C<'. 00
Emergency brake function
An emergency brake ensures tha t the vehicle can
be slowed down even if the
normal brakes fai l
¢ page 88, Emergency braking.
A WARNING
If a drive range is engaged with t he vehicle
stat iona ry and the engine running, you must
in no instance accelerate care lessly . Other­
w ise the vehicle will start to move immed iate­
ly- risk of a n accide nt.
(D Tips
- If the parking brake is app lied with the igni­
tion switched off, the indicator lights in the
switch and . (USA models)/ . (Cana-
da models) in the instrumen t cluster will go
out af ter a ce rtain per io d of t ime .
- Occasiona l noises when the park ing brake is
applied and re leased a re normal and a re not
a cause for conce rn.
- When the vehicle is parked, the park ing
brake goes th ro u gh a se lf-tes t cycle at regu­
l a r i nte rva ls . Any associated noises a re no r­
mal.
Parking
~ P ress the brake ped al to stop the vehicle.
~ Pull the switch c::> page 86, fig. 102 to set the
parking b rake.
~ Move the selecto r lever to P .
~ Turn the eng ine off c::> .&, .
-
~ When on incl ines or declines, turn the steering
wheel so that the veh icle w ill roll into the curb
if it beg ins to move .
A WARNING
-Whe n you leave your ve hicl e -even if onl y
br iefly- alw ays remove the ig nition key. Thi s
applies p articul arly when children rem ain i n
t h e ve hicle . Othe rwise the c hildren could
sta rt the eng ine, release t he parking brake
o r operate elect rical eq uipment (e.g. powe r
windows). There is the risk of an accident.
- When the vehicle is loc ke d , no one - part icu­
larly not children shou ld remain in the vehi-
-
D riving
cle. Locked doors make it more d ifficult for
emergency wo rkers to get into the vehicle -
putting lives at r isk.
Starting from rest
The starting assist function ensures that the
parking brake is released automatically upon starting.
Stopping and applying parking brake
~ Pull the sw itch to app ly the parkin g brake.
Starting and automatically releasing the
parking brake
~ W he n you start to drive as usu a l, t he p ark ing
b rake is automa tic ally released and yo ur vehicle
beg ins to move.
When stop ping at a tr affic sig nal or sto pping in
c ity traff ic on vehicles wi th an aut omat ic t ra ns­
mission, t he parking brake can be app lied . The
vehicle does not have to be held with the foot­
bra ke. The pa rking brake e liminates the tendency
to c reep w ith a dr ive range engaged. As soon as
you drive off as usual, the parking brake is re­ leased a utomat ica lly and the vehicle starts to
move .
Starting on slopes
When starting on incl ines, the sta rting assist pre­
vents the vehicle from un intent iona lly rolling
back. The b raking force of the parking brake is
not re leased unt il su ff icient dr iving force has
been buil t up at t he wheels .
(D Tips
For safety reasons, the park ing brake is re­
l eased automatically on ly when t he d river's
safety be lt is engaged in t he buc kle.
Starting off with a trailer
To prevent rolling back unintentionally on an in­
cline, do the following:
~ Keep the switch pulled and depress the acceler­
ator . The parking brake stays applied and pre-
vents the veh icle from roll ing backward . .,,.
87

CD
CD
.... N ,-... N .... 0 0 C<'. 00
Messages in the instrument cluster display
Applies to: vehicles with Start-Stop -System
Start-stop system : deactivated. Please
restart engine manually
This message appea rs whe n speci fic conditions
a re not met dur ing a stop phase and the S tart­
Stop-System w ill
not be able to restart the en ­
gine. The engine must be started with the key or
with the
! S TAR T ENGINE STOPI* button.
Start-stop system : sy stem fault. Function
una vailable
There is a malfunction in the Start-Stop-System .
Drive the ve hicle to an author ized repa ir facility
for servicing as soon as possible to correct the
malfunct ion.
Transmis sion: Car may roll! Shift to park!
This message appears if the selecto r lever is not
in the
P position w hen the driver's door is
opened. You will also hear a warn ing tone. Shift
the selector lever to the
P posit ion. Otherw ise,
the vehicle could roll.
Speed warning system
Overview
T he speed warning system helps you to keep your
driving speed below a set speed limit.
The speed warning system wa rns if the driver ex­
ceeds a prev io usly stored maximum speed. A
war ning tone w ill sound as soon as the vehicle
speed ex ceeds t he set speed by abo ut
3 m ph
(3 km/ h). At the same time, a warni ng symbo l
appears in the display. The symbol's appearance
might be different in some models .
The speed w arning sys te m has
two warning
threshold s
that function independen tly of each
other an d that have somewhat different purpos­
es:
Speed warning 1
You can use speed war ning 1 to se t the maxim um
speed while yo u are dr iving. This setting w ill re­
main in e ffec t unti l you turn
off the ign ition, as -
Driving
su ming tha t you have not changed or reset the
setting .
T he speed wa rn ing symbol . (U SA mode ls)/ .
(Cana da mo dels) in the warn ing 1 disp lay ap­
pears when you exceed the maxim um s peed.
It
goes out when the speed falls be low the stored
max imum speed.
T he spee d warn ing symbol will also go out if the
speed
exceeds the stored max imum speed by
more than about
25 mph (40 km/h) for at least
10 seconds . The stored max imum speed is delet ­
ed .
Setting spee d warn ing
1 r=> page 92.
Speed warning 2
Stor ing warn ing 2 is recomm ended if you always
want to be reminded of a ce rtain speed, for ex­
amp le when you are traveling in a coun try tha t
ha s a genera l maximum speed limi t, or if you do
not want to e xceed a specified speed for winte r
ti res.
T he spee d wa rn ing
2 symbol, . (USA mo dels)/
• (Cana da models) appears in the display when
yo u exceed the stored speed limit . Unli ke warn ­
ing
1, it will not go out until t he vehicle spee d
drops below the stored speed limit.
Setting spee d warn ing
2 r=> page 92.
(D Tips
Eve n though your vehicle is e quippe d w ith a
s peed w arning system, yo u should still w atch
t he spee dome ter to ma ke sure you are not
d riving faste r than the speed lim it.
91

a,
a,
..... N r-­N ..... 0 0
0:
co
,&_ WARNING
Read and follow all WARNINGS ¢ A in Driv­
ing the automatic transmission on
page 96.
(D Note
Coas ting downhil l w it h t he t ransm iss ion in N
and the engine not runn ing will result in dam ­
age to the automatic transmission and possi­
bly the catalyt ic converter.
(D Tips
- On vehicles with Audi drive select*, you can
adjust the sporty shift characteristics in the
Dynami c driv ing mode .Sw ill appear in the
i nstrument cl uster display instead of 0 .
- If you accidenta lly select N while driv ing ,
take your foot off the accelerator pedal im ­
mediately and wa it for the engine to slow
down to idle before selecting 0/S.
- Hybrid drive*: if the l<=1 •l button ¢
page 103
is pressed wh ile in sport mode S, the trans­
mission switches automatically to the nor­
mal mode 0 .
- If there is a power fa ilure, the selector lever
will not move o ut of the P posit ion . The
eme rgency release can be used if this hap­
pens
¢ page 99 .
Automatic Shift Lock (ASL)
-
The Automatic Shift Lock safeguards you against
accidentally shifting into a forward or the re­
verse gear and causing the vehicle to move unin ­
ten tionally.
•
F ig. 11 0 Shift gate: se le cto r lever lock pos it io ns and re ­
lea se butto n highlig h ted
D rivi ng
The selector lever lock is released as follows :
" Tur n the ignition on.
" Step on t he br ake pedal.
At the same time
press a nd ho ld the release bu tton on the side of
the gear se lector knob
¢ fig . 110 with yo ur
thumb until yo u have moved the selecto r lever
to the desired pos ition.
Automatic selector lever lock
T he selec tor leve r is lo cked in t he P and N posi ­
t io ns w hen the ig nition is tu rned on. You m ust
press the brake peda l and the release button to
select another position . As a reminder to the
driver, the following warn ing appears in the in ­
strument cluster d isplay when the se lector is in P
and N:
When stationary appl y brake pedal while select­
ing gear
T he Au tomatic Sh ift Lock only fu nctio ns when the
veh icle is stationary o r at spee ds be low 1 mph
(2 km/h).
At spee ds above abou t 1 mp h (2 km/h) the Au to­
ma tic Sh ift Lock is autom atically deact ivated in
the N positio n.
A time de lay e lemen t prevents the se lector lever
from lo cking whe n it i s moved thro ugh the N po­
s ition (going from R to D/S) . The locking element
will lock the selector leve r if the lever is left in N
(Ne utral) for more than approximately 1 second,
without the brake pedal being pressed.
Release button
T he release but ton on the selector leve r preve nts
the lever from be ing accidenta lly shifted into cer ­
ta in positions. Pressing this button deactivates
the se lector lever lock . Depending on the d irec­
t ion of the sh ift, the se lector lever locks at d iffer­
ent positions . The posit ions are highlighted in
the i llustration
¢ fig . 110.
Ignition key safety interlock
T he key cannot be removed from the ignition un ­
l ess the selector lever is in the P park position.
When the ignition key is removed , the selector
lever will be locked in the P position.
95

a,
a,
..... N r-­N ..... 0 0
0:
co
The transmission temperature has increased sig­
nificantly due to the sporty driving manner. Drive
in a less sporty manner until the temperature re­
turns to the normal range and the indicator light
switches of.
rm Transmission malfunction: You can continue
driving
There is a system mal funct ion in the transm is­
sion. You may continue driving. Drive to your au­
thorized Audi dealer or qualified repair facility
soon to have the malfunction corrected.
rm Transmission malfunction: Limited driving
functionality
There is a system malfunct ion in the transmis­
sion . T he transmission is switching to emergency
mode. This mode only shifts in to certa in gears or
will no longer shift at all. The engine may stall.
Drive to your authorized Audi dea ler or qualified
repair faci lity immediately to have the malfunc­
tion corrected.
rm Transmission malfunction: Stop vehicle and
shift to park.
Do not continue driving. Select the P selector lev­
e r position and see your a uthorized Aud i dea le r
or qualified repair facility for assistance.
(D Note
If the transmission switches to emergency
mode, you should take the vehicle to an au­
t horized Audi dealership as soon as possible
to have the condition cor rected.
Driving
Selector lever emergency release
If the vehicle's power supply fails, the selector
lever can be released in an emergency.
Fig. 114 F ront center conso le: Removing the ashtray insert
Fig.
11S Selector lever emerge ncy release
.,. To access the emergency re lease mechanism,
remove t he ashtray insert@ using the release
switch @
Q fig. 114.
.,. Loosen and remove the cap in the ashtray
mount
Qfig. 115.
.. You now have access to a pin . Using a screw­
driver or sim ilar object, press the pin down and
hold it in that position .
.. Now press the release button and move these-
lector lever to the N position.
The selector lever can only be moved from the P
position if the key is in the lock and the ignition is
switched on. If the power supply fails (for exam­
ple, the battery is discharged) and the vehicle
must be pushed or towed, move the selector lev­
er to the N position f irst using the emergency re­
l ease .
99

Starting the vehicle
Applies to: vehicles with hybrid drive
The vehicle is started and turned off either wi th
the ign ition key <;>
page 81 or with the
IS TAR T ENG INE S TOPI button* 9 page 84 in t he
same way as a conventional vehicle .
W hen start ing the veh icle, the needles in the in­
s trument clus ter move upward briefly . When the
ve hicle enters d rive ready mode, the s tatus mes­
sage
hybrid ready appears briefly in t he instru­
ment cluster display and the needle in the power
meter points to
READY 9 page 101.
Depending on the ope ration mode of the hybrid
sys tem, there are two possible drive ready modes
after the vehicle has been started:
Drive ready mode with combustion engine
If the ope rat ing req uiremen ts
r;!) page 103 for
e lectric dr ive mode are not met, the combust ion
Power meter overview
Applies to: vehicles with hybrid drive
Hybrid
engine starts the veh icle as usual. You can start
driving as usual.
Drive ready mode with the electric motor
If the operating requireme nts
9 page 103 for
the e lectr ic dr ive mode a re met, the comb ustion
engi ne rema ins off after starting the vehicle .
(j) Tips
To p revent the 12 vo lt batte ry from discha rg ­
i ng, never le ave the vehicle pa rked in the drive
ready mo de. Remove the key from the igni­
tion or press the
I START E N GINE STOP ! but­
ton* . When leaving the vehicle always take
the key with yo u.
The power meter shows the hybrid drive condition and the availability of the hybrid system.
Fig . 116 Power mete r overv iew
An econom ica l dr iv ing and recupe ra tion range is
shown in g reen. A driv ing range that is no t
eco­
nomi cal is shown in o range. In addition , the bat­
tery s tat us provides informatio n about the high
a,
~ voltage batte ry c harge stat us.
N r-­N ...... 0 0
0:
co
@ Fuel efficient driv ing wi thin the
c ombus tion engine's pa rtial load
r a nge
@ System limits for electric driving in
the EV mode
@ El ectr ic dr iving o r driv ing with the
c ombust ion engine ( EFFICI ENCY)
101

Hybrid
© Vehicl e drive ready (READY)
® High voltage battery charge status
® Recuperation (CHARGE)
(j) Driving within the combustion en-
gine's full load range
® 100% combust ion engine
® Boosting -the electric engine as-
sists the combustion engine
(BOOST)
@ Engaging the conventional brakes
with recuperat ion
@ Vehicle not drive ready (OFF)
@ EV mode act ive
The needle remains at
OFF when the ignition is
turned on. When the vehicle enters drive ready
mode, the status message
hybrid ready appears
briefly in the instrument cluster display and the
needle in the power meter points to
READY.
Indicator lights and messages
App lies to: ve hicles w ith hyb rid drive
The indicator lights in the instrument cluster
b lin k or tu rn on. They indicate functions or mal­
f unct ions.
With some indicator lights, messages may ap­
pear and a warning tone may sound . Also note
the indicator l ights in
¢page 24.
Press brake pedal to start vehicle
This message appears if you do not press the
brake pedal when starting the vehicle .
Shift to N or P to start vehicle
This message appears if the selector lever for the
automatic transmission is not in the Nor P posi­
tions when starting the vehicle.
- Hybrid drive: System fault! Power
brakes, steering malfunction possible
lfthe indicator light turns on and this message
appears, there is a malfunction in the hybrid sys­
tem . The brake booster and the power steering
may stop working. Stop the vehicle in a safe loca­
tion as soon as possible.
102
You may continue driving i f the i ndicator light
turns off after starting the vehicle several times .
Drive to an authorized repair facility immediate ly
to have the malfunction corrected .
Q/ij:@,j rlybrid drive: System fault! Contact
dealer
If the indicator light turns on and this message
appears, there is a malfunction in the hybrid sys­
tem. Drive to an authorized repair fac ility imme­
diately to have the malfunct ion corrected.
(II Hybrid system: Performance restricted.
Please contact dealer
If the indicator light turns on and this message
appears, there is an eng ine control malfunction .
The
ffa i ndicator light in the instrument cluster
also turns on. The engine output is reduced.
D rive to your authorized Audi dealer or qualified
r epa ir facility immediate ly to have the malfunc­
tion corrected.
Hybrid drive deactivated. Please restart
engine manually.
This message appears if the high vo ltage battery
charge level has fallen below a certain range or if
the ignition key is no longer inside the vehicle for
vehicles with the convenience key* .
Start the engine wit h eithe r the ignition key
¢
page 81 or with the !START ENGINE STOPI
button* ¢ page 84.
Hybrid battery: Low battery charge. Battery
will be charged while driving.
This message appears if the high vo ltage battery
charge level has fallen below a certain range. If
this message turns off after a litt le while, the
high voltage battery charged enough while driv­
i ng.
If the message does not turn off, have an author­
ized repair facility correct the ma lfunction as
soon as possib le .
EV mode is currently unavailable .
This message appears if the conditions
¢ page 103 for enha nced elect ric driving are not
met. Try again at a la ter time .

Audi adaptive cruise control and braking guard
c:::::, ___ c:::::,_ Distance 3 : This setting corresponds
to a distance of 164 feet/SO mete rs when trave l­
ing at 62 mph (100 km/h), or a time interval of 1.8 seconds .
c:::::, ____ c:::::, Distance 4 : This setting corresponds
to a distance of 210 feet/64 meters when trave l­
ing at 62 mph (100 km/h), or a time interval of
2 .3 seconds .
_&. WARNING
Following ot her vehicles too closely increases
the risk of collisions and ser ious personal in­
jury.
- Setting short distances to the traffic ahead
reduces the t ime and distance ava ilable to
br ing your vehicle to a safe sto p an d makes
i t eve n mo re necessary to pay close atten­
t ion t o traffic.
- Always obey applicable traffic laws, use
g ood ju dgment, and select a safe f ollow ing
di st ance f or th e tra ffic, road and we athe r
c ondition s.
¢j) Tips
- Distance 3
is set au tomati cally e ach time
yo u sw itch th e ig nit io n o n.
- Y our sta ndard setti ngs a re a uto mat ica lly
stor ed and as signed to th e re m ote contro l
k ey be ing used ¢
page 33 .
Setting the dr iving program
A pp lies to: ve hicles w ith Audi adaptive cruise co ntro l
Depending on t he se lec ted dr iv ing program and
d istance, dr iv ing behavior whe n accelerating wi ll
vary from dynamic to comfo rtable.
Setting the driving program for vehicles
without Audi drive select*
~ In the radio/ MM!*, selec t: !CARI function but ­
ton
> adaptive cruise control > Driving pro­
gram
> Comfort , Standard or Dynamic. Or
~ Se lect : I CARI funct ion button > Car systems*
contro l button > Driver assist > Adaptive cruise
control
> Driving program > Comfort, Stand­
ard
o r Dynamic .
114
Setting the driving mode for vehicles with
Audi drive select*
Refer to ¢page 123 .
(D Tips
Your set tings are automatic ally store d and as ­
signed to t he remote contro l key being used
¢ page 33 .
Request for driver intervention
App lies to: vehicles wi th Audi ada ptive c ru ise control
Fig. 131 I n str um ent cl uste r: re quest for driver interve n­
t io n
In certain situations, the system will prompt yo u
to take ac tion . This could happen, for example, if
braki ng by the adaptive cruise cont rol sys tem is
not en ough to ma in tain enough dis tance to t he
vehicle a he ad .
The ins trument cluster w ill warn you about the
dange r¢
fig . 131 :
-A red veh icle is pictured in the d isp lay.
- The te xt
DISTANCE! appears in the status bar .
- The red indicator light . blinks .
- In ad dition, a wa rni ng tone so unds .

Audi adaptive cruise control and braking guard
promptly detected or may not be detected
at all.
- Reflective surfaces including crash barriers
or tunnel entrances may impair the function
oftheradarsensor.
(D Tips
-You can cancel the braking that is initiated
by the system by braking yourself, by accel­
erating noticeably or by swerving.
- Braking guard error messages
c:> page 116.
- Keep in mind that braking guard can brake
unexpectedly. Always secure any cargo or
objects that you are transporting to reduce
the risk of damage or injury.
Settings in the radio/MMI*
Applies to: vehicl es w ith Audi adaptive cruise control
.,. Select : ICARI function button> Audi braking
guard .
Or
.,. Select:
~I C~A~R~I function button > Car systems*
control button > Driver assist> Audi braking
guard .
System -
Switch braking guard On and Off. When
you switch the ignition on, the message
Braking
guard: Off
appears if the system is switched off .
Early warning -The distance and approach warn­
ings in the display can be switched
On/Off .
(D Tips
-Your settings are automatically stored and
assigned to the remote control key being
used at the times the settings are made
r=;,page 33.
-If you restrict the ESC, the braking guard al­
so switches itself off
c:> page 18 7.
- Switch braking guard
off when you are load­
ing the vehicle onto a vehicle carrier, train,
ship or other type of transportation . This
can prevent undesired warnings from the
braking guard system.
Messages
Applies to: vehicles w ith Audi adaptive cruise contro l
Braking guard: Off
116
This driver message appears if the system is
turned
off via the radio/MM I*. Otherwise, if the
system is turned
off, the information appears ev­
ery time shortly after the start of the trip.
The driver message also appears if the system is
not available due to a malfunction or if the ESC is
not switched on
c:> page 187. If this is the case,
the system will not provide warnings about a possible collision.
Braking guard: Activated
This driver message appears if sharp brake pres­
sure was applied due to an acute warning.
•••
Three white dots appear if a setting cannot be se­
lected with the operating lever . For example, this
happens if you want to raise/lower the speed
even though there was no previously saved
speed.
ACC: Sensor blocked
This message appears if the sensor view is ob­
structed, for example by leaves, snow, heavy
spray or dirt. Clean the sensor
r=;, page 109,
fig. 122 .
ACC: Unavailable
The driver message appears if, for example, the
brake temperature is too high. The adaptive
cruise control is temporarily unavailable. A chime
sounds as a rem inder.
ACC: Not available
The driver message appears if there is a malfunc­
tion. The adaptive cruise control turns off. A
chime sounds as a reminder. Have the system
checked by an authorized Audi dealer or author­
ized Audi Service Facility.
Shift lever position!
The driver message appears if the selector lever
is shifted to the N position. The adaptive cruise
control is not available while in this position.
Stabilization control (ESC)
This message appears if the Electronic Stabiliza­
tion Control (ESC) is taking action to stabilize the .,.