ECO AUDI Q7 2008 4L / 1.G Infotainment MMI Operating Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2008, Model line: Q7, Model: AUDI Q7 2008 4L / 1.GPages: 193, PDF Size: 6.18 MB
Page 3 of 193
Foreword
Thank you for choosing the MMI infotainment system.
Your new Audi is designed with the latest technology, enabling you to control all on-board elec-
tronic systems and other settings via menu displays in the Multi Media Interface, the Audi MMI.
We recommend that you read this Operating Manual carefully so that you quickly become familiar
with all the available functions of the MMI and can take full advantage of them in everyday use.
Please note that this Operating Manual is intended to supplement the information in the Owner's
Manual for your vehicle, so it should only be used in conjunction with the current edition of the
Owner's Manual. These instructions are also included in the electronic Audi On-board Handbook.
Should you have any further questions regarding the MMI in your car, please contact your Audi
dealer.
We wish you safe and enjoyable motoring with your Audi.
AUDI AG
Page 5 of 193
Contents3
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Entering the PIN/PUK code . . . . . .
Emergency calls . . . . . . . . . . . . . . .
Dialling a telephone number . . . .
Answering and ignoring telephone
calls . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending calls . . . . . . . . . . . . . . . . . . .
Storing a telephone number in the
directory . . . . . . . . . . . . . . . . . . . . . .
Dialling a stored telephone number
Other settings for the Bluetooth car
telephone kit . . . . . . . . . . . . . . . . . .
Other settings for the phone pre-
installation . . . . . . . . . . . . . . . . . . . .
Navigation. . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . .
Activating navigation mode . . . . .
Entering a destination . . . . . . . . . .
Stopping the route guidance . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . .
Storing a destination . . . . . . . . . . .
Loading a destination . . . . . . . . . .
Other settings . . . . . . . . . . . . . . . . .
Calling up traffic information. .
Introduction . . . . . . . . . . . . . . . . . . .
Calling up traffic reports (TP memo)
Setting a traffic station . . . . . . . . .
Calling up a traffic message . . . . .
Other settings . . . . . . . . . . . . . . . . .
Multi-function steering
wheel
. . . . . . . . . . . . . . . . . . . . . . . .
Basic operation . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . .
Adjusting the volume . . . . . . . . . . .
Listening to the radio . . . . . . . . . . .
Playing media . . . . . . . . . . . . . . . . . .
Television . . . . . . . . . . . . . . . . . . . . . .
Using the telephone . . . . . . . . . . . .
Navigation . . . . . . . . . . . . . . . . . . . . .
Voice control . . . . . . . . . . . . . . . . . . .
Telephone handset. . . . . .
Basic operation . . . . . . . . . . . . . . . .
Switching the handset on and off
Overview of the keypad . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . .
Using the telephone . . . . . . . . . . .
Placing calls . . . . . . . . . . . . . . . . . . .
Speed and one-touch dialling . . . .
Answering and ignoring telephone
calls . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency calls . . . . . . . . . . . . . . . . Ending calls . . . . . . . . . . . . . . . . . . . .
Options during a call . . . . . . . . . . . .
Answering and replacing further
calls . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menus. . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . .
“Last calls” menu . . . . . . . . . . . . . . .
“Phone book” menu . . . . . . . . . . . . .
“ Text messages” menu . . . . . . . . . .
“Settings” menu (handset) . . . . . . .
Vo i c e c o n t r o l . . . . . . . . . . . . . .
Telephone speech control
system . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . .
Basic operation . . . . . . . . . . . . . . . . .
Name tags . . . . . . . . . . . . . . . . . . . . .
Speech recognition for some
export markets . . . . . . . . . . . . . . . . .
Storing names in the phone book*
Selecting a name from the phone
book* . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting a name from the phone
book* . . . . . . . . . . . . . . . . . . . . . . . . . .
Speech dialogue system . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . .
Basic operation . . . . . . . . . . . . . . . . .
Name tags . . . . . . . . . . . . . . . . . . . . .
Listening to the radio . . . . . . . . . . . .
Playing an audio CD . . . . . . . . . . . . .
Using the directory . . . . . . . . . . . . . . 88
89
90
92
92
93
94
94
101
104
104
105
105
110
110
112
114
116
121
121
121
122
122
123127
128
128
129
129
130
131
132
136
137
139
140
140
140
142
145
145
146
147
147148
149
150
151
151
152
153
154
155
159
160
160
161
164
167
167
168
168
169
169
170
172
174
175
175
Page 13 of 193
Media drives11
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Media drives
General notes on CD/DVD operation
These general notes apply to audio CDs and navigation
DVDs.
Requirements for good sound reproduction
Please note the following in order to ensure perfect high-quality
sound reproduction and avoid damage to media drives:
•Do not use damaged or scratched CDs or DVDs .
•Do not use single CDs (diameter 8 cm / 3 inches) .
•Do not use non-circular CDs (shape CDs) .
•Do not use labels .
•Do not use protective rings .
•Do not use dirty CDs or DVDs.
•Do not use a CD cover or a stabiliser.
•Always store unused CDs/DVDs in a suitable CD case and do not
expose them to direct sunlight.
Cleaning media drives, CDs and DVDs
Never use a CD player cleaning disc to clean the media drives.Clean CDs and DVDs with a soft, lint-free cloth. Wipe the disc in a
straight line from the centre outwards. If necessary, dirt can be
removed with a commercially available CD cleaner or with isopropyl
alcohol. Please never use petrol, paint thinner or record cleaner, as
these can damage CDs and DVDs.
Use of laser equipment
Laser devices are divided into the safety classes 1 to 4, as specified
by DIN IEC 76 (CO) 6/ VDE 0837. The audio devices used on your
vehicle are classified as safety class 1. Lasers used in devices that
fall into this category are very weak and well screened, so there is
no danger if used correctly.
Read errors
If the display indicates a read error, any of the following causes are
possible:
Note
•Under certain circumstances audio CDs that are copy-protected
or CDs that do not comply with the standard audio format cannot be
Fig. 2 CDs that should
not be used.
AA
AB
AC
AD
AE
ProblemRemedy
CD/DVD is dirty.Clean the CD/DVD.
CD/DVD is scratched.Replace the CD/DVD with a
scratch-free CD/DVD.
CD/DVD was inserted upside
down.Insert the CD/DVD with the text
facing upwards.
Condensation has formed on
the CD/DVD.Wait until the CD/DVD is dry.
A mechanical malfunction has
occurred on the media drive.Contact an Audi dealer or quali-
fied workshop.
Page 15 of 193
Media drives13
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Loading a CD
– Press the button page 12, fig. 3. When the
CD changer is ready for loading, the red diodes in the CD
slot will flash.
– Insert the CD (text facing upwards) into the CD slot ,
holding it straight. The CD will automatically be loaded
into the next available position in the CD changer. The
diode light in the corresponding button will stop
flashing.
Loading all CDs
– Press and hold the button for more than 2
seconds.
– Wait until the red diodes in the CD slot flash.
– Insert all six CDs (text facing upwards) one at a time into
the CD slot , holding them straight. The button diodes
for the occupied positions will stop flashing.
Loading a CD in a specific empty position
– Press the button . The button diodes for any
empty positions will begin flashing.
– Press one of the flashing buttons .
– Wait until the diodes in the CD slot flash.
– Insert the CD (text facing upwards) into the CD slot ,
holding it straight.
Loading a CD in a specific occupied position
– Press the button . The diodes in buttons will
be illuminated to indicate which positions are already
loaded with a CD.– Press one of the illuminated buttons . The CD at that
position will then be ejected.
– Remove the CD from the slot .
– Insert the CD that you wish to load (text facing upwards)
into the slot , holding it straight.
If you press the button again while loading all CDs, the
loading process will be stopped.
After it has been ejected, the CD will automatically be pulled back
into the CD changer after about 30 seconds if it is not removed from
the CD slot.
Note
Please observe the notes for handling CDs page 11.
Changing CDs
– Press one of the illuminated buttons page 12, fig. 3.
The CD inserted at this position will then be played.
Ejecting CDs
Ejecting a CD
– To eject the CD that is currently playing, press the eject
button page 12, fig. 3.
– To eject any CD, press the eject button and then one
of the illuminated buttons page 12, fig. 3.
Ejecting all CDs
– Press and hold the eject button for at least two
seconds. All of the CDs are ejected one after the other.
LOADA3
A2
A2
A4
LOADA3
A2
A2
A4
LOADA3A4
A4
A2
A2
LOADA3A4
A4
A2
A2
LOAD
A4
A1
A1
A4
A1
Page 16 of 193
Media drives 14
After it has been ejected, the CD will automatically be pulled back
into the CD changer after about 30 seconds if it is not removed from
the CD slot.
Note
Please observe the notes for handling CDs page 11.
DVD navigation drive
Applies to vehicles: with navigation system
Introduction
Eject button
DVD slot
Depending on the equipment fitted on the vehicle the DVD drive
may be located in the side compartment on the left of the luggage
compartment or underneath the floor panel of the luggage
compartment.
You cannot use the Navigation functions if you have not inserted a
navigation DVD in the DVD drive. TMC traffic messages will then not
be displayed.
Note
You can obtain navigation DVDs from your Audi dealer. Your Audi
dealer will also be able to provide information on updates which are
available for the DVDs.
Applies to vehicles: with navigation system
Loading a navigation DVD
Do not use any force when inserting the navigation DVD
into the drive. The DVD will be drawn into the slot auto-
matically.
– Make sure that no navigation DVD is already loaded in
the drive page 14.
– Insert the navigation DVD into the drive fig. 4, keeping
it level (printed side facing upwards).
After the navigation DVD has been loaded, the display will show
“Navigation is being initialised”. You can use the function as soon
as the message disappears.
If the message “Please check navigation DVD” appears in the MMI
display, the Navigation function cannot be used.
Note
Please observe the notes on handling navigation DVDs page 11.
Applies to vehicles: with navigation system
Ejecting a navigation DVD
– Press the eject button fig. 4. The navigation DVD
will then be ejected.
Fig. 4 DVD player for
navigation system
A1
A2
A1
Page 18 of 193
Media drives 16
Caution
Handle the adapter cable with care. Make sure the cable does not
become pinched or trapped.
Applies to vehicles: with Audi music interface and adapter cable - under development at the
time of printing
Disconnecting an adapter cable from the
Audi music interface
Important: The glove box and the cover cap on the Audi
music interface page 15, fig. 5 must be open.– Press the connector fig. 7 in towards the Audi
music interface.
– Then press down the release tab fig. 7 on the
connector. The connector will be released.
– With the release tab pressed down, pull the connector off
the Audi music interface fig. 8.
Caution
•To avoid damaging the connection, please take care when
detaching the connector from the Audi music interface.
•Handle the adapter cable with care. Make sure the cable does not
become pinched or trapped.
Applies to vehicles: with Audi music interface and iPod adapter cable - under development
at the time of printing
Connecting an iPod via an iPod adapter cable
The iPod is connected to the Audi music interface via the
iPod adapter cable.
Connecting the iPod connector
– Connect the iPod adapter cable to the iPod.
Fig. 7 Adapter cable:
Releasing connector
on Audi music inter-
face
Fig. 8 Adapter cable:
Detaching released
connector from Audi
music interface
A3
AA
AB
AC
Fig. 9 Detaching iPod
connector from iPod
!
Page 19 of 193
Media drives17
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Disconnecting the iPod connector
– Release the connector by pressing both knobs
page 16, fig. 9.
– Carefully pull the connector out of the iPod .
When it is connected, the iPod can be put away in the storage bay
page 15, fig. 5.
The iPod battery is charged via the adapter cable when the iPod is
connected to the Audi music interface and the ignition is switched
on.
The following iPods can be connected to the iPod adapter cable:
•iPod Mini (versions 1.3.0, 1.4.0 and 1.4.1)
•iPod nano 1G - First Generation (versions 1.1, 1.1.1 and 1.3)
•iPod 5G - Fifth Generation Video (version 1.1.2)
•iPod 4G - Fourth Generation (version 3.1.1)
Other versions cannot be used with the iPod adapter cable. You can
connect these devices as portable players using the optional
adapter cable with 3.5 mm jack plug* page 18.
Any problems with the iPod will also affect the operation of the MMI.
In this case, please reset your iPod (see operating instructions)
The following iPod control functions are not supported by the MMI:
•Star rating for music tracks
•Jump to a specific place in a track
•Add tracks to the “on-the-go” playlist
•Display the “compilations” folder. Similarly, tracks marked “part
of a compilation” are not included in the artist list if the compilation
function was activated in the iPod.
Note
•For more information on operating the iPod via the MMI, please
refer to the sections starting on page 63.
•Please refer to the iPod operating instructions for important
information on how to use your iPod.
•We recommend that you update the iPod software to the latest
status.
•Your Audi dealership will be able to provide the latest informa-
tion on the Audi music interface.
Applies to vehicles: with Audi music interface and USB/mini USB adapter cable - under
development at the time of printing
Connecting a portable player via a USB/mini
USB adapter cable
Different USB memory devices can be connected to the
Audi music interface via a USB/mini USB adapter cable.
When connected, the memory devices can be put away in the
storage bay page 15, fig. 5.
The Audi music interface supports USB memory devices belonging
to the “USB Device Subclass 1, 2 and 6”. The manufacturer will
provide you with information on the “USB Device Subclass” of a USB
memory device.
The following USB memory devices are supported:
•USB sticks
•Single card readers
•Multiple card readers (first card slot used)
•USB MP3 players that do not require special driver software
•External USB flash memory
•External USB hard drives (HDD) - 1", 1.8", 2.5" drives with a max.
starting/continuous current of 800 mA
For information on how to operate the USB memory device via the
MMI, please refer to sections starting on page 63.
MP3/ WMA files must meet the following specifications:
A1
A2
Page 20 of 193
Media drives 18
Please note that music files are copyright-protected.
Note
•You can shorten the process of scanning for music files on the
connected USB memory device by creating a central folder for
music files and playlists and positioning it as the first item (alpha-
betically) on the memory device.
•Do not use USB extension cables or adapters as these impair the
functionality.
•The Audi music interface does not support DRM-protected files.
•In view of the variety of USB memory devices and the difference
in memory capacities, the functionality may be restricted in the case
of some memory devices.
•For up-to-date information please see the internet, e.g.
“www.audi.com”.
•An iPod shuffle cannot be used with the USB/mini USB adapter
cable.
Applies to vehicles: with Audi music interface and 3.5 mm jack plug/adapter cable - under
development at the time of printing
Connecting a portable player via an adapter
cable (with 3.5 mm jack plug)
You can connect your portable player (e.g. MP3 player) to
the Audi music interface using the adapter cable with
3.5 mm jack plug.
– Connect the 3.5 mm jack plug to the earphone connec-
tion of your portable player. The audio source is then
played through the sound system of your vehicle.
If the Audi music interface is already selected as the source
page 63, fig. 54, you may hear some brief interference (a noise
often occurring on home stereo systems) when you connect or
disconnect the 3.5 mm jack plug. To avoid this interference, you can
either activate the mute function page 45 or another audio
source (radio page 54, CD page 63) before connecting and
disconnecting the portable player.
Note
We recommend setting the output level of the portable player to
about 70 percent of maximum. You can adjust the volume level (for
instance to match the radio volume) via the Input level function
page 70.
MP3 filesWMA files
FormatMPEG-1, MPEG-2
MPEG-2.5Version 7, 8 and 9
StandardISO 9660 Level 1 and 2
File systemFAT16, FAT32
File namesDisplay of file names may be restricted by MMI
screen.
Bit rates8 to 320 kbit/s and vari-
able bit rate64 to 320 kbit/s and vari-
able bit rate
No. of filesMax. 500 files per directory
(function restricted with more than 500 files)
Structure of
foldersMax. 7 subfolders
PlaylistsMax. 119 playlists, no more than 1000 entries per
playlist
Playlist
formatsM3U, PLS, B4S
ID3 tags/
WMA tagsVersion 1, 1.1, 2.2, 2.3
and 2.4,
max. 30 charactersVersion 7, 8 and 9,
max. 30 characters
Page 24 of 193
Phone pre-installation 22
Applies to vehicles: with phone pre-installation
Bluetooth™
Bluetooth enables a wireless connection between a
mobile phone and the MMI system.
The mobile phone 3) must be bonded to the on-board phone
system in the vehicle (only has to be done once). This proce-
dure involves various steps, depending on the mobile
phone you are using. After you switch on the ignition, you
have 5 minutes to connect your mobile phone to the on-
board phone system (while the vehicle is stationary).
– Make sure that no other mobile phone is connected to
the on-board phone system via Bluetooth.
– Switch on the ignition and the MMI (if not already acti-
vated).
– Select the appropriate menu option on your mobile
phone to search for Bluetooth compatible devices
(phone pre-installation).– Connect the mobile phone to the on-board phone
system. Your on-board phone system will use the name
“Audi UHV” when it connects with the mobile phone.
– Enter the PIN for handsfree mode (“1234”) on the on-
board phone system within 30 seconds.
– Wait until your mobile phone indicates that it has
bonded. The Bluetooth symbol fig. 14 will appear
on the MMI display.
You should change the PIN for handsfree mode to prevent unauthor-
ised use of your mobile phone page 101.
Up to four mobile phones
You can bond up to four mobile phones to the on-board phone
system. However, it is only possible to activate one connection at a
time. If you bond a fifth mobile phone to the on-board phone
system, the system will delete the device which has not been used
for the longest time in conjunction with the on-board phone system.
Connecting and disconnecting
A mobile phone which has been bonded to the on-board phone
system and is ready to operate will be connected automatically
when you switch on the ignition. On some mobile phones you have
to confirm the connection.
The Bluetooth connection is terminated when the key is removed
from the ignition lock.
Range
The Bluetooth connection between the mobile phone and the on-
board phone system is restricted to the interior of the vehicle. The
connection can be susceptible to interference caused by other elec-
tronic devices or obstacles between the devices. For example, the
transmission quality may be affected if you keep your mobile phone
in your jacket pocket.
3)Please make sure that the mobile phone you are bonding supports the
Hands-Free Profile.
Fig. 14 Bluetooth
symbol
A1
Page 26 of 193
Bluetooth car telephone kit 24
Bluetooth car telephone kit
Applies to vehicles: with Bluetooth car telephone kit
Introduction
The car telephone kit has a universal interface, which
means that different types of mobile phone can be
connected using Bluetooth technology.
The car telephone kit is approved for use in GSM 900 and GSM 1800
networks. The functionality of SIM cards for UMTS networks may be
limited in certain circumstances.
Bluetooth profiles
Bluetooth devices use profiles to communicate with each other. The
SIM Access Profile and the Hands-Free Profile are used to exchange
data between Bluetooth phones and the car telephone kit. Please
check which profiles are supported by your mobile phone.
Mobile phones which support both the Hands-Free Profile and the
SIM Access Profile can use all of the telephone functions on the car
telephone kit. These telephone functions are appended with the text
“Mobile phone with SIM Access Profile” in this Operating Manual.
Mobile phones which support only the Hands-Free Profile cannot
use all of the telephone functions on the car telephone kit. These
telephone functions are appended with the text “Mobile phone with
Hands-Free Profile” in this Operating Manual.
Mobile phone with SIM Access Profile
SIM Access Profile means that a car telephone kit can access the SIM
card on a Bluetooth-capable mobile phone via a Bluetooth connec-
tion.
You can use your mobile phone's SIM card, phone book and tele-
phone functions on the car telephone kit as long as your mobile
phone is fully compatible with the car telephone kit. Telephone calls
are directed via the external aerial. This reduces the radiation inside
the vehicle and improves the quality of the telephone connection.Handset* for the car telephone kit
If your vehicle is equipped with a car telephone kit and handset*,
you can insert a SIM card in the handset*. Alternatively, you can
bond a mobile phone (with SIM Access Profile) to the car telephone
kit and use the mobile phone's SIM card functions on the handset*.
Please refer to page 27 for information on how to set up the
system.
Mobile phone with Hands-Free Profile
Hands-Free Profile means that a mobile phone can be connected to
the car telephone kit via Bluetooth. The handsfree system on the car
telephone kit can then be used to make phone calls. Not all of the
telephone functions on your car telephone kit will be available.
Please refer to page 28 for information on how to set up the
system.
The external car aerial is not used. The handset* cannot be used.
The following can be used for operation
•MMI* page 87
•Handset* for the car telephone kit page 30
•Multi-function steering wheel* page 132
•Speech dialogue system* page 169 or telephone speech
control system* page 160
WARNING
•Always place the handset* back into the carrier after use.
Otherwise, you could place yourself or others at risk when braking
or during an accident.
•Health organisations recommend keeping a minimum distance
of 15 centimetres between an activated handset* and a pace-
maker to avoid interference between the two units.