navigation update AUDI Q7 2008 4L / 1.G Infotainment MMI Operating Manual

Media drives 14
After it has been ejected, the CD will automatically be pulled back
into the CD changer after about 30 seconds if it is not removed from
the CD slot.
Note
Please observe the notes for handling CDs
page 11.
DVD navigation drive
Applies to vehicles: with navigation system
Introduction
Eject button
DVD slot
Depending on the equipment fitted on the vehicle the DVD drive
may be located in the side compartment on the left of the luggage
compartment or underneath the floor panel of the luggage
compartment.
You cannot use the Navigation functions if you have not inserted a
navigation DVD in the DVD drive. TMC traffic messages will then not
be displayed.
Note
You can obtain navigation DVDs from your Audi dealer. Your Audi
dealer will also be able to provide information on updates which are
available for the DVDs.
Applies to vehicles: with navigation system
Loading a navigation DVD
Do not use any force when inserting the navigation DVD
into the drive. The DVD will be drawn into the slot auto-
matically.
– Make sure that no navigation DVD is already loaded in
the drive
page 14.
– Insert the navigation DVD into the drive
fig. 4, keeping
it level (printed side facing upwards).
After the navigation DVD has been loaded, the display will show
“Navigation is being initialised”. You can use the function as soon
as the message disappears.
If the message “Please check navigation DVD” appears in the MMI
display, the Navigation function cannot be used.
Note
Please observe the notes on handling navigation DVDs
page 11.
Applies to vehicles: with navigation system
Ejecting a navigation DVD
– Press the eject button
fig. 4. The navigation DVD
will then be ejected.
Fig. 4 DVD player for
navigation system
A1
A2
A1










Navigation 104
Navigation
Applies to vehicles: with navigation system
Introduction
Let the “Global Positioning System” (GPS) guide you to
your destination.
Wasting time studying confusing maps and tediously planning
routes are things of the past! Now you can simply enter your desired
destination into the navigation system, and the route guidance will
guide you directly to it. You can also set up to three stopovers on the
way to your destination.
The route guidance will be transmitted in the form of spoken cues
that will inform you in good time of any necessary turns, stops etc.
In which language would you like to hear the route guidance? You
can select any of the following languages: German, English, French,
Italian, Portuguese, Spanish or Dutch. You can have the last route
guidance cue repeated by pressing the right-side thumbwheel on
the multi-function steering wheel
page 137.
A detailed route map is displayed on the MMI screen
page 110.
You can also receive information on your route via the driver infor-
mation system
page 111.
If you do not want to follow a certain route guidance cue, no
problem! The navigation system will re-calculate the route from the
current location of the vehicle. In addition, if the dynamic navigation
function is activated, the navigation system will even take into
account traffic reports so that you can reach your destination even
faster.
If the vehicle is located in a place that cannot be identified by the
software (e.g. car park), a speech cue will inform you of this.
WARNING
•Today's driving conditions require the full attention of drivers.
Please see
page 9, “Notes on traffic safety”.
•Pay attention to traffic rules when driving.
•The route calculated by the navigation system is a recommen-
dation of how best to reach a destination. Pay attention to traffic
lights, no stopping signs, lane change restrictions, one-way
streets, etc.
Caution
•Should the navigation directions contradict the current traffic
regulations, you must always follow the traffic regulations.
•The volume should only be set at a level which enables you to
hear distant police and emergency vehicles clearly - failure to do so
could result in an accident.
Note
•Snow or other obstructions on the GPS aerial or interference
caused by trees or large buildings could affect the reception of the
satellite signals and make positioning difficult. GPS reception and
vehicle positioning can also be adversely affected by deactivation or
a malfunction of several satellites.
•Street and town names can change, therefore the names stored
on the DVD can in some cases be different from the names that have
since been changed.
•The navigation DVDs can only be purchased from Audi dealers.
They can also provide you with information on the most recently
updated navigation DVDs.










Navigation115
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the rotary pushbutton. The top category destina-
tion will be set as the final destination or as a stopover.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Note
To update the list of top categories, exit the list by pressing the
button and select the same category again.
Applies to vehicles: with navigation system
Loading from the directory
Important: The navigation mode must be activated

page 105, and a navigation destination must be stored in
the directory
page 84.
– Press the Memory control button.
– Turn the rotary pushbutton to Load from directory.– Press the rotary pushbutton. A list of entries
fig. 105
will appear in the MMI display.
– To select a destination from the list turn the rotary push-
button to mark the entry and press to confirm, or
– To find an entry, turn the rotary pushbutton to Find entry
and press to confirm. You can now search for a name
using the speller.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Applies to vehicles: with navigation system
Route
Routes that have been stored previously can be loaded as
a new navigation destination.
Important: The navigation mode must be activated

page 105, a route must have been stored
page 113,
and the system must be set to Route with stopover

page 105.
– Press the Memory control button.
– Turn the rotary pushbutton to Load route.
– Press the rotary pushbutton. A list of entries will appear
in the MMI display.
– To select a route from the list turn the rotary pushbutton
to mark a route and press to confirm.
RETURN
Fig. 105 Loading desti-
nation from directory