spare tire AUDI Q7 2009 Owner´s Manual

lll'Jl,___W_ h_ a_ t_ d_o_ l_ d_ o _ n_ o_w _ ? ____________________________________________ _
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Activate the vehicle jack mode (only vehicles with Adap­
tive Air Suspension) ~
page 210.
2. Remove the decorative wheel cover*. For more details
see also~
page 375, "Decorative wheel covers" or
~ page 375, "Wheels with wheel bolt caps".
3. Loosen the wheel bolts ~ page 376.
4. Locate the proper mounting point for the jack and align
the jack below that point~
page 376.
5. Lift the car with the jack~ page 376.
6. Remove the wheel with the flat tire and then install the
inflatable spare tire =>
page 378.
7. Tighten all wheel bolts lightly.
8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten all wheel
bolts
~ page 376.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode (only vehicles with
Adaptive Air Suspension)=>
page 210.
& WARNING
Always read and follow all WARNINGS and information => & in
"Raising the vehicle" on
page 376 and => page 379. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 120 ft lb (160 Nm).
- Have t he flat tire
replaced as soon as possible.
[ i] Tips
• I f you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque .
• Drive at reduced speed until you have the tightening torques
checked .•

lllftl.___W_ h_ a_ t_ d_o_ l_ d_ o _ n_ o_w _ ? ____________________________________________ _
Taking the wheel off/installing the inflatable
spare tire
Follow these instructions step -by-step for changing the
wheel
Fig. 306 C han ging a
w heel : align ment pin
insid e the to p ho le
After you have loosened all wheel bolts and raised the
vehicle off the ground, remove and replace the w heel as
follows :
Removing the wh eel
- Remove the topmost wheel bolt complete ly and set it
aside on a clean surface.
- Screw the t hreaded end of the alignment pin from the
tool kit hand-tight into the empty bo lt hole ~ page 378,
fig. 306.
T hen remove the other wheel bolts as descr ibed above.
- Take off the wheel leaving t he alignment pin in the bolt
hole .
Putting on the inflatable spare tire
-Inflate the inflatable spare tire~ page 378 and push the
wheel over the alignment pin . - Sc
rew in and tighte n all wheel bolts slightly.
- Remove the a lignment pin and insert and tighten the
remaining wheel bolt slig htly like the rest.
- Tu rn the jack handle counter -c lockwise to lower the
veh icle until the jack is fully released.
Use the wheel bolt w rench to tighten a ll wheel bolts
firmly ~ page 376. Tighten them crosswise, from one
bolt to the (approximately) opposite one, to keep the
wheel centered .
[ i ] Tip s
• When mounting tires with un idi rect io n al t rea d de sign make sure
the tread pattern is pointed the right way =>
page 379.
• The whee l bolts should be clean and easy to turn. Check for dirt
and corrosion on the mating surfaces of both the wheel and the
hub . Remove a ll dirt from these surfaces before remounting the
wheel. •
Inflating inflatab le spare tire
- Remove the compressor from the luggage compartment
~ page 372, fig. 300.
- Unscrew the va lve stem f rom t he spare tire.
- Screw the ti re fi lier hose f rom the compress or firmly o nto
the valve of t he spare tire.
- Insert the plug from the comp ressor into a socket of the
veh icle ~ page 118.
- Sw itch the compressor on .

_______________________________________________ W_ h_ a_t _ d_ o_ l _d _o_ n_ o _ w_ ? __ IIIII
•
- Let the compressor run until it has reached 50 PSI (3.5
bar). Switch the compressor off after running for 8
minutes at the most -danger of overheating!
& WARNING
The compressor and the tire filler hose can become extremely hot
while they are running -danger of burns!
0 Note
Switch the compressor off after running for 8 minutes at the most -
danger of overheating! Allow the compressor to cool down for a few
minutes before you use it again.
[ i] Tips
The compressor must not be connected to the cigarette lighter
socket, as this socket does not provide the required power .•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern intended for use
in a specific direction
When using a spare tire with a tread pattern intended for use in a
specific direction, please note the following:
• The direction of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction, use
the spare tire only temporarily since the tire will not be able to
achieve its optimum performance characteristics with regard to
aquaplaning, noise and wear. •
We recommend that you pay particular attention to this fact
during wet weather and that you adjust your speed to match road
conditions.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible to restore the handling advantages of a
unidirectional tire. •
Notes on wheel changing
Please read the information => page 359, "New tires and replacing
tires and wheels " if you are going to use a spare tire which is
different from the tires on your vehicle.
After you change a tire :
• Check the tire pressure on the spare immediately after installa­
tion.
• Have the wheel bolt tightening torque checked with a torque
wrench as soon as possible by your authorized Audi dealer or a
qualified workshop.
• With steel and alloy wheel rims, the wheel bolts are correctly
tightened at a torque of 120 ft lb (160 Nm).
• If you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible. Remount the wheel cover.
Until then, drive with extra care and at reduced speeds .
& WARNING
• If you are going to equip your vehicle with tires or rims which
differ from those which were factory installed, then be sure to read
the information
=> page 359, "New tires and replacing tires and
wheels". ..
Do-it -yourself service

lllftl.,___F_ u_ s_ e_s _ a_n _ d_ b_ u_lb _ s _______________________________________________ _
[ i J Tips
You are well advised to keep a supply of spare fuses in your vehicle .
Fuses with the proper ampere ratings are available at your autho ­
rized Audi dealer. •
Fuse Location, Instrument Panel left
Fig . 309 Fuse panel
layout
Some of the equipment items listed are optional or only available on
certain model configurations .
Note that the following table is accurate at the time of going to
press and is subject to change. In the event of discrepancies, the
label on the inside of the cover always takes precedence.
The power seats are protected by circuit breakers, which automati­
cally reset after a few seconds after the overload has been reme ­
died.
No.
Equipment
Fuse holder (red)
1
2
3
Not used
Not used
Not used
Amps
No. Equipment
4 Tire pressure monitoring system
5 Not used
6 Lumbar support driver's seat
7 Window regulators (left side of vehicle)
8 Door control module (left side of vehicle)
9 Battery energy management
10 Electronic ignition lock,
power steering column adjustment
11 Switch module steering column
12 Intelligent
power module convenience
Fuse holder (brown)
1
2
Not used
Not used
3 Not used
4 Wiper system
5 Rain sensor
6 Horn
7
8
9
Intelligent power module driver
Intelligent power module driver
(lights left side of vehicle)
Intelligent power module driver
(lights right side of vehicle)
10 Instrument cluster
11 Headlight washer system
12 Diagnostic connector
Fuse holder (black) Amps
5
10
35 15
5
30
10 5
30
5
25
30
25 25
10
30
10
-

__________________________________________________ C_o_ n _ s_u_ m_ e ___ r_l_ n _f_ o_ r _m...:....:.. a:.;..:. ti .... o:.. n ........ _llll
& WA RNIN G (continu ed )
• The engine compartment of any motor vehi cle i s a potentially
h az ardou s area. N ev er re ach into the are a arou nd or to uch the
r a di ator fan . It is temperature co ntrolled and can swi tc h o n
s uddenly -even wh en the engine i s off and the ignition key h as
been removed . The r adiator f an switches on autom atic all y w hen
the coolant reache s a certain temperature and will continue to run
until the coo lant t emper ature drop s.
• Alway s remov e th e ignition key befo re anyone get s under the
v ehi cle .
• Alway s s upport your vehi cle with safety sta nd s if it i s ne ces­
sa ry to wor k unde rne ath the veh icle . The ja ck suppl ied with the
v ehic le i s not adequ ate for thi s purpo se and could coll ap se
c au sin g s eriou s per son al in jury .
• If you m ust w ork under neath the vehi cle with the wheel s on
the ground , alwa ys m ake sure the veh icle i s on l eve l ground , that
the wheels ar e always securely blocked and that the engine
ca nn ot be sta rted .
• Alway s mak e sure the tran sm iss ion selecto r leve r (automatic
tr ansmi ssion ) is in "P " (P a rk po sition ) and the park brake is firml y
applied .
c£> For the sake of the environment
• Changing the engine settings w ill adverse ly affect emission
levels . This is detrimenta l to the environment and increases fuel
consumption.
• Always observe environmenta l regu lations when disposing of
old engine oil, used brake fluid, dirty engine coolant, spent batteries
or worn out tires.
• Undeployed airbag modules and pretens ioners might be classi ­
fied as Perchlorate Material -specia l handling may apply, see
www .dtsc .ca .gov/hazardouswaste/perchlorate. When the vehicle or
parts of the restraint system including airbag modules safety belts
with pretens ioners are scrapped, all applicable laws and regu la-
Controls and equip­
ment Safety first Vehicle operation
tions must be observed. Your authorized Audi dealer is familiar with
these requirements and we rec
ommend that you have your dea ler
perform this service for you .•
Additional accessories ,
modifications and parts replacement
Addition al a ccessori es and parts
replacement
Always c onsul t an authorized Audi dealer before
purchasing accessories.
Your vehicle incorporates the latest safety design features ensuring a high standard of act ive and passive safe ty .
This safety could be compromised by non -approved changes to the
vehic le . F or this reason, if par ts have to be replaced, please observe
the following points when insta lling additiona l accessories:
Approved Audi accessories and genuine Audi parts are avai lable
from authorized Audi dealers.
These dealers also have the necessary facilities, tools and trained specialis ts to install the parts and accessories prope rly.
& WARNING
Using the wrong spare part s or u sing non-approved acce ssorie s
can c ause seri ous persona l injur y.
• Use onl y acc essorie s ex pres sly approved by Audi and g enuine
Audi spare p art s
• The se p art s and acce ssorie s have been spe cia lly de signed to
be used on you r vehi cle .
• Nev er in stall acc ess orie s s uch a s telep hone cra d le s or
be ver age holder s on airb ag cover s or within th e airbag deploy-
Vehicle care Do-it-yourself service Tec hn ica l da ta

______________________________________________ A_ l_,_ p _h_ a_ b_e _t_i c_ a _ l _in _ d_e _ x __ ffllll
How many airbags does my vehicle have? ..
248
How often should I check my tire pressures? 354
How safety be lt pretensioners work .... 239
Hydroplaning .... .... ....... .. .. .... 358
I
Ignition key .... .... .... .... ... .... . 142
Ignition lock .. .... ...... .... ... .... . 142
Malfunction .. ... .... ...... .... 34, 38
Ignition lock positions ... .... ...... .. 142
Immobilizer . .... .... .... ... .... .... . 15
Important things to do be fore d riving .. 221
Improper ly worn safety belts ..... ... .. 239
I ndicator lights ..... ... .. ........... . 17
Airbag system . ........ ...... 252, 253
PASSENGER A IR BAG OFF ... .. ... .. 253
Infant seats . .... ... .... .... .... .... 268
How do I properly install an infant seat in
my vehicle? .... ..... .... ..... .. 268
Safety instructions ... .... ... .... . 268
I nflatable spare tire ...... ... ... .... .. 372
I nflating .... . ... ... . .. .. .. .... .. 378
Inside rear view m irror . ...... ... ... 86, 87
Ins ta lling child sa fe ty sea ts
Safety belts ....... ......... ..... 273
I nstrument cluster i lluminat ion ... ..... . 17
I nstruments and controls .... .... .... .. 13
General il lustration ... .... ....... .. 11
Int erior lights .... .... .... ... .... ..... 78
Rear . ....... ... .... .... ....... 78, 79
Controls and equip­
ment Safety first
I
ntermittent wiping LATCH ...... .... ... . ... ... . .. .. .. . . 278
Rain sensor ... ...... .... ... .. .... . 81 Descrip tion ... ... ... ... .. .... .... 278
Guidance fix tures for lower anchorages .
J 279
Installing a child restraint ...... .... 281
Jack .... .... .... ...... ..... ..... .. . 370
Location . .... .... .... ... .... .... 278
Jumper cab les . ...... .... ... .... .... 388 Mounting and releasing the anchorage
Jump -starting ... ...... ... .. .... .... 387 hook .
..... .. ... .... ... .... .. .. 282
Lateral angle .. ... ...... .... ..... .. . 302
K Leather ...... .... .... ... .. .. ... .. .. 321
Cleaning .. .... .... ... ........ ... 322
Key .... .... .... .... ... ...... ....... 48
Level adjustment
Battery rep lacement .. .... .... .... . 50
See Adaptive Air Suspension ... .. .. 206
Coded settings . ... .... .... ... .... 123
Lifting jack ... .... .... ... .... .... ... 376
Convenience opening a nd closing of
windows ... .... .. .. ..... .. . .... . 66
Emergency key ...... ........ ..... . 48
Key replacement . .... .... .... .... . 48
Master key ... ....... .... .... .... . 48
Valet key ... .. .... .... .... ... .... . 48
Key coded settings Climate controls ... .... ..... .. .... 123 Lifting vehicle .
....... ... .. .. .... ... 392
Light Exterior light ing in the mirror housing 76
leaving home ..... .... ... .... .... . 76
See also Background lighting ...... .. 79
Light sensor defective ....... ... .. ..... 36
Lighting
Key less entry remote control ... .. .... .. 49
Kick -down
See Background lighting ... .... .... . 79
Ligh ting in the mirror hous ing ..... ... .. 76
tiptronic® .... .... .... .... .... ... 187 Lights
.. .. .. .... .... .... ... .... .... . 73
Coming home . .... .... ...... .... .. 74
L
Daytime running lights ............. 74
Emergency flashers ... .... .... ... .. 76
L ane assist Exterior lights ..
... .... ... ..... .... 74
Activating and deact ivating 171 Front fog l
ights ... .... .... .... ... .. 75
Description ... .. .. .... .... .... ... 1 71 Headlights ..
...... .... .. . .. .. .... . 73
Instrument cluster indicator light . .. 171 H
igh beam .... .... ... .. .. .... . 73, 77
MMI settings ... .. .... .... .... ... 172 High beam warning/indicator light
... 22
Notes on instrument c luster disp lay . 171 Leaving h
ome ...... ... .. .. ... .. .. . 7 4
Vehicle operation Vehicle care Do-it-yourself service Technical data