key AUDI Q7 2014 Owner´s Manual

52 Openin g and clo sing
opened are the power windows switched
off.
- Be careful when closing the windows .
Check to see that no one is in the way, or
serious injury could result!
- Always remove the ignition key whenever
you leave your vehicle.
- If you lock your vehicle from the outside,
no one, especia lly children, sho uld re­
main in the vehicle .
- Do not stick anything on the windows or
the windshield that may interfere with
the driver's fie ld of vision.
In addition to t he switches in the drive r's
door there is a separate switch in each
door for the power window in that door
¢ page 53, fig. 47.
Switches in the driver's door
T he driver can operate all windows.
I f the respective switch is pushed or pulled
the w indow will open or close. The power win­
dow switches have a
two -positi on fun ction :
Opening the windows
.. Push the sw itch to the fir st stop and hold i t
there unt il the wi ndow has lowered to the
desired position.
.. Push the switch briefly to the
second stop:
the window wi ll automatically open all the
way.
Closing the windows
.. Pull the switch up to the fir st stop and ho ld
it there until the window has risen to the de ­
sired position .
.. Pull the switch quick ly to the
second po si­
tion :
the w indow w ill automatically close all
t he way ¢
A in Controls on page 5 l.
Activating /deactivating the r ear windows
.. Press the left[!] switch ¢ page 51, fig. 46 to
deactivate only the window regulator in the
left door . The indicator light in the switch i l­
luminates.
.. Press the right[!] switch ¢ page 51, fig. 46
to
d eactiv ate only the window reg ulator in
the
right door. The ind icator light in the
sw itch illuminates .
.. Press the
1±1 sw itch aga in to reactivate the
w indow regu lator . The indicato r light in the
sw itch goes out .
If you press both
1±1 switches ® in succession,
the following funct ions are switched off in the
rear of the vehicle:
- The window regulator switches in the rear
doors .
- The buttons for the Panoramic slid ing su n­
roof* .
- On veh icles with rear climate control*, oper­
ation from the rear is blocked . Dashes" ---"
are show n in the displays for the rear cli­
mate cont ro ls, and the rear air-cond ition ing
can only be operated from the climate con­
trols in the cabin ¢page 98.
- I f
only th e left 1±1 sw itch was pressed, the
w indow regu lator in the
left rear do or and
t he buttons in t he rear for the Panoramic
sliding sunroof* are deactivated . In addi­
t ion , the door is locked .
- If
o nly the right[!] switch was pressed, the
w indow regu lator in the
right re ar door and
the buttons in the rear for the Panoramic
sliding sunroof* are deactivated . In addi ­
tion, the door is locked.
T his feature has been provided for the safety
of small children riding in the rear of the ve hi­
cle .
(D Tips
- T he windows can sti ll be opened and
closed for about ten minutes after the
ignition has been t urned off . The powe r
w indows are not shut off unt il one of the
front doors is opened.
- In order to act ivate the child safety lock
on the left and the right side, you have to
press the two safety switches in succes­
sion . Make certa in that the check light
comes on the correspond ing safety

switch when the chi ld safety lock is acti ­
vated .
Switch in the front passenger 's door and
on the rear doors
F ig. 4 7 Swit ch loca tion front pass engers door
The power window sw itch has a two-po sit ion
function :
Opening the windows
.. Pre ss the sw itch to the fir st position and
hol d it unt il you have opened t he window as
f ar as yo u wan t.
.. Press the sw itch quick ly to the
second po si­
tion
and the window w ill automatically open
all the way .
Closing the windows
.. Pull the swi tch to t he first po sition and hold
i t u ntil you have closed the window as far as
yo u want .
.. Pull the switch q uickly to the
second posi ­
tion
and the window wi ll automatically close
all the way.
(D Tips
The windows can st ill be opened and
closed for abo ut ten minutes after the ig ­
nition has been t urned off . The powe r win­
dows are not sh ut off until o ne of t he front
doors is opened .
Opening and clo sin g 53
Convenience close/open feature with the
lock in the dr iver 's door
I
You can close or open the windows from out­
side when you lock or unlock your car wi th the
key in the driver's door lo ck .
Fig. 48 Key turns for opening and closing
Closing windows
.. Insert the key into the lock of the dr iver's
door .
.. Make s ure that the windows are not blocked
¢ _& .
.. Tu rn and hold the key in the lock posit ion @
¢ fig. 48 unt il the windows and the Panor­
amic sliding sunroof * with the power s un
blin d are comp letely closed.
Opening windows
.. Insert the key into the lock of the driver 's
door .
.. Tur n and hold the key in the open pos it io n
@ .
The automatic close/open f unction w ill cease
if the key is returned to its orig inal pos ition .
A WARNING
-
- Be careful wh en clos ing the w indows .
Che ck to see t hat no one is in the way, o r
ser ious injury could result!
- Always rea d an d h eed WARN ING
¢ A in
G eneral descrip tion on p age 42.

Opening front r oof segment to comf ort
se ttin g
"Turn the rotary switch ¢ fig. 49@ to posi­
tion ©, you will feel the switch engage . The
roof segment is slid open only to a comfort
position w ith low wind noise. This is the rec­
ommended standard sett ing for normal
driv ing cond itions .
Sliding front roof segment full y open
" Rotate and hold the switch @ in position @
unt il the roof segment has reached the de­
s ired pos it ion. There may be increased wind
noise in this pos it ion.
(D Tips
- In posit ion @, the switch jumps back to
pos ition © again as soon as the switch is
released .
- When dr iv ing with the Panoramic slid ing
sunroof open, open the front roof seg ­
ment to the comfort setting to m inim ize
wind noise .
Closing Panoramic sliding sunroof
Applies to vehicles: with Panoram ic sliding sunroof
Clos ing tilted front roof segm ent
" Pull the switch¢ page 54, fig . 49 @ and
ho ld it until the roof segment has reached
the des ired pos ition.
" Pull the switch
brie fly to close the roo f seg­
ment automatica lly. By activating the switch
briefly again, the roof segment can be stop­
ped in any position ¢
.&_.
Clos ing front r oof s egment wh en slid
o p en
" Rotate switch ¢ page 54, fig. 49@ to posi­
t ion @ to close the roof segment
c::> .&_. To
move to an intermediate posit ion, rotate the
switch to the corresponding click-stop .
Clos ing tilt ed r ear roof segm ent
" Tap the rocker switch ¢ page 54, fig. 49 ®
or
c::> page 54, fig. 50 © in the front area Q
br iefl y to close the roof segment completely
c::> .&_.
Opening and clo sin g 55
"To set an intermediate position manually,
press the rocker switch in the front area~
until the roof segment has reached the de­
sired tilt posit ion
c::> .&_ .
A WARNING
Improper use of the Panoram ic sliding
sunroof can cause serious personal injury.
- Be careful when closing the Panoramic
-
sliding sunroof . Not paying attention
could cause you or others to be trapped
and injured as the Panoram ic sliding sun­
roof closes.
- Always take the key w ith you when you
leave the vehicle to prevent injur ies
caused by the Panoramic slid ing sunroof
clos ing
- Never leave children or persons requiring
assistance alone in the vehicle, especially
when they could access the vehicle keys .
Unsupervised use of the keys can result
in the engine being started or use of ve­
hicle systems such as the power win­
dows, etc. wh ich could result in serious
injury. The doors could be locked with
the remote key, de laying help in an
emergency.
- The Panoramic slid ing sunroof will con­
tinue to operate until the ign ition key
has been removed and one of the front
doors has been opened.
Convenience closing feature
Applies to vehicles: wit h Pa noramic slid ing sunroof
The Panoramic sliding sunroof can be closed
from outside with the key in the driver's door lock .
" Insert the key into the dr iver's door lock.
" Turn and hold the key in the lock pos it ion ®
c::> page 43, fig . 33 until the Panoramic slid­
ing sunroof is complete ly closed
c::> A in
Closing Panoramic sliding sunroof on
page 55.
T he power s un blind is a lso closed . .,..

58 Clear vis ion
lig ht sensor checked as soo n as poss ible at an
author ized Audi dealer or qua lified wor kshop .
.&_ WARNING
-Daytime ru nning lights and automatic
headlights are only intended to assist
the driver. They do not relieve the driver
of his respons ib ility to check the head­
lights and to turn them on manually ac­
co rding to the current light and v is ibi lity
condit ions. For example, fog cannot be
dete cted by the light sensors*. So alw ays
switch on the headlights
io u nder these
weather conditions and when driving in
the dark.
- Crashes can happen when yo u cannot see
the road ahead and when you cannot be seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see yo ur car from
the back.
- Please obey a ll laws when using the
lighting systems described here.
@ Tips
- With the switch in AUTO front fog lights
and rear fog lights cannot be turned on in addition.
- The light senso r for headlight contro l is
l ocated in the rear view m irror mount.
You should therefore not app ly any st ick­
ers to the windsh ield in this area in o rder
to preve nt ma lfunctions o r failures.
- Some exterior lighting functions can be
adjusted
c:> page 58.
-When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sou nds as long as the driv­
er's door is open .
- In coo l o r damp weather, t he ins ide of
t h e headlights, turn signa ls and tail
li ghts can fog ove r du e to t he tempera­
tu re diffe re n ce between the inside and
outside. They will cle ar sho rtly after
swi tching them on. This does not affect
t h e service li fe of the lighting . -
In the event o f a light sensor malfunc­
tion, the driver is notified in the instru­
ment cl uster display
c:> page 35 .
Adjusting exterior lighting
The functions are set in the MMI.
• Sele ct: I CAR I function butt on > System s*
control but to n > Exterior lighting . Or
.. Select:
I CAR I function button > Car systems *
contro l butto n > Vehicle settings > Exterior
lighting .
Coming home (Lights when leaving car ),
Leaving home (Lights when unlock ing car )
The coming home f unction ill uminates the
area o utside the vehicle when you tu rn the ig­
nition off and open t he driver's door. Depend­
ing on vehicle equ ipment, the f unction can be
switched on and off or the length of t i me the
lights remain on* can be adjusted .
The leaving home illum inates the area outside
t h e ve hicle when yo u unlock the vehicle . This
funct ion can be switched on and off .
The Coming home and Leaving home func­
tions only operate when it is dark and the light switch is in the
AUTO pos ition.
Daytime running lights
USA model s: The daytime r unning lights can
be turned on or off using th is function.
Canada model s: Th e fu nction cannot be
turned off .
It is activated automatically each
time the ignition is t urned on. This menu item
is shown "greyed out" .
Front fog lights
Fig. 54 Instrument pa nel: light switch

Notes o n these featur es
- The turn signals only work with t he ignition
turned on . T he indicator light s
II or Ill in
the instrument cluster
¢ page 14 also b link.
- After you have turned a corner , the tur n sig-
nal switches off automatica lly.
- The
high beam works only when the head­
lights are on. The indicator light
II in t he
instrument cluster i lluminates when the
high beams a re on.
- The
headlight flasher wo rks only as long as
you hold the lever -even if there are no
lights turned on . The indicator light
II in
the ins trument cluster illuminate s when you
u se the headlight flasher .
A WARNING
-
Do not use the high beam or headlight
flasher if you know that thes e cou ld blind
oncoming traffic.
Interior lights
Front interior lights
The interior lights include reading lights for
both the driver and the front passenger .
Fig. 59 Headlin er: Fro nt in te rior /re adi ng light s
The rocker switch @¢ fig. 59 for ope rating
the in ter ior lighting has the follow ing func­
tions :
Door cont act switch
.,. Place the switch @ in the midd le position.
Interior light switched on
.,. Pla ce the switch @ in posi tion I.
.,,
:! .:,
1A
Clear vision 61
Interior light switched off
.,. Place the sw itch @ in position 0 .
Reading lights ~
.,. Press one of the switches @ to turn the
r ight or left reading light on or off .
In the door contact swi tch position (switch @
in the m iddle position), the interior l ights tur n
o n as soon as you unlock the vehicle o r open
the doors . The inte rior lights are also turned
o n when the igni tion key is removed . The light
goes ou t about 30 seconds after the doo rs are
closed. When the veh icle is locked or when
the igni tion is turned on, the i nterior lights
are turned off .
When a door is open, the interior lights are
tu rned off after about 10 minutes to prevent
draining the battery.
T he brigh tness of the lights is cont rolled au­
tomat ic all y by a d imme r when they are
switched on and off.
Rear interior lights
There are reading ligh ts in the rear for the
passengers .
0
...
Fig . 60 Headli ner: Rear read ing light s
>l!i:.
r -
' \.
Fig. 61 Headlin er: Third row r eading light
N .., N
.:,
1A
:::i N
-.:,
1A

68 Clear vision
Changing the rear wiper blade
Fig. 69 Rear w indow wiper Detac hing the rear wipe r
bl ade
Removing the wiper blade
.,. Fold the w indshield wiper arm away from
the glass .
.,. Grasp the upper end of the wiper arm with
one hand and the metal clamp on the wipe r
blade with the other
¢fig. 69 .
.,. Hold the wiper arm in the direction of the
arrow @and pull the w iper blade out of the
holder only in the direction of the arrow @.
Attaching the wiper blade
.,. Adjust the w iper blade in the holder.
.,. Hold the upper end of the wiper arm with
one hand .
.,. Press the w iper blade into the holder with
your other hand.
.,. Fold the wiper arm back onto the wind­
shield .
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice a
year.
-
Mirrors
Adjusting the exterior mirrors
Fig. 70 Forward sectio n of drive r's armrest: powe r mir­
ror controls
Adjusting exterior mirrors
.,. Rotate the knob to the © position (driver's
exte rior m irror) or to the@ position (pas­
senger's exterior m irror)
9 fig. 70 .
.,. Rotate the knob and the mirror so that you
have a clear view to the rear.
Heated mirrors
.,. Rotate the knob to position@ .
Folding both exterior mirrors flat*
.,. Rotate the knob to position @.
Depending on the outside temperature, the
mirror surfaces are heated until the ignit ion is
switched off -even if the knob is no longer in
pos ition @.
You are we ll-advised to fo ld the exter ior mir­
rors in when maneuver ing in tight spaces or
when leaving the car parked close to other
vehicles.
Memory setting for the exterior mirrors*
When the seat position is saved in the memo­
ry, the position of the exterior mirrors is saved
at the same time
9 poge 74.
If the position of the passenger m irror is
changed when the vehicle is in reverse gear
and the switch is in the ® position, this new
ti lted position wi ll be automatically saved to
the remote key when the vehicle is taken out
of reverse gear. To save, the rotary knob for
mirror adjustment must be in the ® position, ...,

Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted
correctly . We recommend that you adjust the
passenger's seat in the following manner:
.. Move the front passenger seat into the rear ­
most position of the fore and aft adjustment
range
~ .&. in Why is your seat adjustment
so important? on page
72.
• Bring the backrest up to an (almost) upright
position.
Do not ride with the seat reclined.
.. Adjust the head restraint so the upper edge
is as even as possible with the top of your
head . If that is not possible, try to adjust
the head restraint so that it is as close to
this position as possible ¢
page 77 .
.. Place your feet on the floor in front of the
passenger's seat .
Power front seat
adjustment
Seat adjustment controls
The operating logic for the switches corre­
sponds to the cons truction and function of
the seat.
ui
"' ~ -" __.___,., 1,--~--,-,:,
Fig. 74 Front seat: Co ntr ols for seat a djustment
The switches to adjust the seat cushion and
the seatback correspond to the layout, the de­
sign and the function of the seat. The seats
are adjusted by moving the switches following
this logic.
Seats and storage 73
Controls
@ Seat adjustment
® Seatback adjustment
© Lumbar support
Adjusting the seat
Position, angle and shape of the seat can be
adjusted electrically to ensure safe and com­
fortable seating .
Read and follow the warning notices¢.&. be­
fore you adjust your seat .
Fore-and-aft adjustment
.. Push the switch @forward or backward
¢ page 73, fig. 74 .
Adjusting seat height
.. Pull or push the switch @up or down.
Front seat cushion up/ down
.. Press the switch @at the front up or down .
Rear seat cushion up/ down
.. Press the switch @at the rear up or down.
Adjusting seatback angle
.. Push the switch @ forward or backward.
Adjusting the curvature of the lumbar
support
.. Push the switch plate© forward or back­
ward to increase or reduce the curvature.
Adjusting the height of the lumbar
support
.. Push the switch plat e© up or down to posi­
tion the curvature higher or lower .
A WARNING
-Adjust the driver's seat only when the ve­
hicle is stationary. You risk an accident
otherwise.
- The power adjustment for the front seats
also works with the ignition sw itched off
or with the ignition key removed. For this
reason, children should never be left
IJIJ>

7 4 Seats and storage
unattended in the vehicle -they could be
injured!
- Exercise caution when adjusting the seat
height. Unsupervised or careless seat ad­
justment can pinch fingers or hands causing injuries.
- While the vehicle is moving, the seat­
backs of the front seats must not be in­
clined too far to the rear because the ef­
fectiveness of the safety belts and the
airbag system is severely compromised -
there is a risk of injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers must never ride in a moving ve­
hicle with the seatback reclined . Safety
belts and the airbag system only offer
maximum protection when the seatback
is upright and the safety belts are prop­
erly positioned on the body. The more
the seatback is reclined, the greater the
risk of personal injury from an incorrect
seating position and improperly posi­
tioned safety belts .
Seat memory
Driver's seat memory
Applies to vehicles: with seat memory
The seat adjustment settings for two drivers
can be stored using the memory buttons in
the driver's door.
Fig. 75 Drive r's door : Se at me mory
In addition to the setting for the driver 's seat,
the settings for the steering column* and both exterior mirrors can be stored .
Storing and recalling settings
Using the memory buttons 1 and 2, you can
store and recall the settings for two different
drivers ¢
fig. 75.
The current settings are also automatically as­
s igned to the remote control key being used
when the vehicle is locked. When the vehicle
is unlocked, the settings assigned to the re­
mote control k ey b eing used are automatically
recalled. This function has to be activated in
the MMI ¢
page 75 , Ac tiva ting remo te con­
trol key memory.
Turning seat m emory on and off
If the I ON/OFF I switch is depressed, the seat
memory is inoperative. The word
OFF next to
the
ION/O FF! switch illuminates.
All the stored settings are retained. We rec­
ommend using the
I ON/O FF I switch and deac­
tivating the seat memory if the vehicle is only
going to be used
temporarily by a driver
whose se tting s are not going to be stored.
Storing and recalling a seat position
Applies to vehicles: with seat memory
Before you can store or recall your seat posi ­
tion, the
ION/OFF I button must be engaged
(down) .
Storing settings
.,. Adjust the driver 's seat ¢ page 73 .
.,. Adjust the steering column*¢ page 103 .
.,. Adjust both outside mirrors¢ page 68. In
the tilt-down position, the passenger mirror
can be adjusted to the preferred position
and saved in the seat memory .
.,. Press the
ISETI button and hold it down. At
the same time, press one of the memory
buttons for at least one second .
.,. Release the buttons. The settings are now
stored under the corresponding memory
button.
Recalling settings
.,. Driver's door open -press the desired mem-
ory button . _..

~ Driver's door closed -press the correspond­
ing memory button until the stored position
is reached.
Successful storage is conf irmed audibly and
by the light in the
!SE T! button illuminating.
When the vehicle is
locked, the current set­
tings are stored and ass igned to the remote
control key. But the settings stored on memo ­
ry buttons
1 and 2 are not deleted. They can
be recalled at any time. When the vehicle is
unlocked, the settings assigned to the remote
control key are restored.
I f your vehicle is driven by other persons using
your remote control key , you should save your
individual seat position on one of the memory
buttons. You can recall your settings again
simply and conven iently by pressing the corre­
spond ing memory button . When the vehicle is
locked, these settings are automatically re-as­
signed to the remote control key and stored.
A WARNING
-For safety reasons, the seat setting can
only be recalled when the vehicle is sta­
tionary -othe rwise you risk having an ac­
cident.
- In an emergency, the recall operation
can be stopped by pressing the
!ON/O FF I
button or by briefly pressing any given
memory button.
Activating remote control key memory
Applies to vehicles: with seat memo ry
To assign the driver's seat settings to the re­
mote control key when locking the vehicle, the
function must be activated in the MMI.
~ Select: I CARI function button > Systems*
control button > Seat adjustment > Driver 's
seat> Key mem. profile
> On. Or
~ Select : I CARI function button > Car systems*
control button > Vehicle settings > Seats >
Driver's seat> Remote control key> On.
Seats and storage 75
(D Tips
If you do not want another driver's set­
tings to be assigned to the remote control key, switch off the memory function using
the MMI or the
I ON/OF F! button
¢ page 74.
Rear seats
General information
Safe transportation of passengers on the rear
seats requires proper safety precautions .
All passengers on the rear seats must be seat­
ed in compliance with the safety guide lines
exp lain ed in
¢page 174 and ¢page 183.
The correct seating position is criti ca l for the
sa fety of front
and rear seat passengers alike
¢page 167.
A WARNING
-Occupants in the front and rear seats
must always be properly restrained.
- Do not let anyone ride in the vehicle
without the head restraints provided.
Head restraints help to reduce injuries.
- Loose items inside the passenger com­
partment, can fly forward in a crash or
sudden maneuver and injure occupants.
Always store articles in the luggage com­
partment and use the fastening eyes, es­
pecially when the rear seatbacks have
been fo lded down .
- Read and heed all WARNINGS
¢ page 167, Proper seating positions
for passengers in rear seats .

88 Seats and storage
Outlet
An electrical accessory can be connected to the 12-vol t power outlet.
Fi g. 10 0 Section from center console: 12-volt ou tlets
Fig. 101 Sect ion from righ t sid e of lu ggage compar t­
ment: 12-vol t outle t
• Remove the cover from the o utlet
¢ fig. 100.
• Lift up the cover for the outlet ¢ fig . 101.
• Pl ug in appliance to be used.
The 12-volt outlets can be used for electrical
accessories. The power input must not exceed
120 watts.
There may be just one out let at the front of
the center conso le depending on your model.
There are two additional 12-vo lt outlets in the
rear center console.
Before you purchase any accessories, always
read and fo llow the information in
¢ page 318, Additional accessories and parts
replacement.
_&. WARNING
The outlet p lus any appliances plugged in­
to it rema in functiona l even if the ignition
is switched off or the ignit ion key is re- moved. Never leave chi
ld ren inside the ve­
h icle w ithout supervision.
(D Note
To avoid damaging the outlet, only use
p lu gs that fit properly .
(D Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle ba t­
tery can still be d rained .
Storage
General overview
There are numerous places to store items in
your vehicle .
Glove compartmen t ¢page89
Cooling box i n glove compart-¢page89
ment
Sto rage compartment in roof
¢ page 90
Coat hooks ¢page90
Storage in th e door panels ¢ page 90
Storage net in footwell ¢ page 90
Storage net i n the front seat -¢page 91
backs
S to rage net i n luggage com-
¢ page91
pa rtment
Storage compartment beneath
¢page83
cargo floor
A WARNING
-Always remove objects fro m the inst ru­
men t pa nel. Any items not stored could
slide around inside the vehicle whi le dr iv­
i n g or when acce le rating o r when app ly ­
i n g the brakes or when driving around a
corner.
- W hen you are driving make sure that
anyth ing you may have placed in the cen­
ter conso le or other storage locations
cannot fall out i nto t he footwells. In case
of sudden braki ng you would not be able
-
to b rake or accelerate. liJ,,