check engine AUDI Q7 2018 Owner´s Manual

Cl a:, ...... N
" N ...... 0
0
::r - Adding engine oil
Fig. 264 Engine compa rtment : en gin e oil fille r opening
cover
Observe the safety p recautions r=:> .&. in Working
in the engine compartment on page
319 .
"'Turn the eng ine off.
"' Open the hood
r=:> page 320.
"'Unscrew the cap~ for the eng ine oi l filler
opening
r=;, fig. 264.
"' Carefully add 0.5 quart (0.5 liter) of the correct
oi l
r=;, page 321.
"'Close the engine oil filler opening cap.
"' Close the hood.
"' Restart the ignition after two mi nutes and read
the current o il level in the Infotainment system
r=:> page 322 , Checking the engine oil level.
"' Add more oil if necessa ry .
.8, WARNING
- Whe n add ing o il, do not let oil d rip on to hot
engine components . This increases the risk
of a fire.
- Yo u m ust seal the cap on the oil fi lle r open ­
ing correctly so that oil does not leak out
onto the hot engine and exhaust system
when the eng ine is running, because this is
a fire hazard.
- Always clean skin thoroug hly if it comes into
contact with engine oil.
- Engine oil is poisonous and must be kept
out of reach of c hil d ren .
- Store the engine oi l securely in the original
container.
(Q) Note
- If the message Ill Plea se redu ce oil level
appea rs, there is too much oil in the engine
Ch eck ing and F illing
and there is a risk of catalyt ic converter and
engine damage . Do not start the engine.
Contact an authorized A udi dealer or au ­
thori zed Audi Service Fac ility to have excess
eng ine oi l extracted if necessary.
- Your Limited New Vehicle Warranty does not cover damage or malfunctions due to
failure to fo llow recommended mainte­
nance and use requ irements as set fort h in
the Audi Ow ne r's Manua l and War ranty
&
Ma intenance booklet.
- Use only a h igh quality engine o il that ex­
press ly complies with the Audi o il quality
s tandard spec if ied for yo ur vehicle's eng ine.
Us ing any othe r oi l can c ause ser io us eng ine
damage.
- Do not mix a ny addit ional lubr ican ts into
t he engine oil. Damage caused by such add i­
t ives is no t covered by the warranty .
@ For the sake of the environment
-Oil sho uld neve r en ter the sewer system or
c ome in to con tact w ith the ground.
- Pay attent ion to lega l requirements when
disposing of empty o il conta iners.
Changing the engine oil
We recommend that have your oil changed by an
authorized Audi dealer or a qualified service sta­ tion.
Befo re you check anything in the engine compart­
ment,
a lwa ys read and heed all WARNINGS r=;, &.
in Working in the engine compartment on
page
319.
T he eng ine o il must be changed according to the
i nterva ls spec ified in your War ranty
& Ma inte­
nance booklet . This is ve ry importa nt because the
l u brica ting proper ties of oil dim inish g radua lly
during norma l vehicle use .
U nder some c ircumstances the engine oil s hou ld
be c hanged more freq uent ly. Cha nge o il more of­
ten if you dr ive mostly s hort d istances, operate
the vehicle in dusty areas or under p redominantly
stop-and -go traffic conditions, or have your ve hi­
cle where temperatures remain be low free zing
for extended periods.
323

Check ing and F illing
Detergent additives in the oil will make fresh oi l
look dark after the engine has been running for a
short t ime. Th is is norma l and is not a reason to
change the oil more often than recommended.
Because of the prob lem of p roper disposa l, along
with the special tools and necessary expertise re­
qu ired, we strongly recommend that you have
your oil changed by an authorized
Audi dealer or
a qualified service station .
If you choo se to change your oil your self , please
note the following important information:
A WARNING
To reduce the risk of personal injury if you
must change the engine oil in your veh icle
yourself:
- Wear eye protection.
- To reduce the risk of burns from hot engine
o il, let the eng ine cool down to the touch.
-
- When removing the oi l drain plug with your
fingers, stay as far away as poss ible. A lways
keep your forearm paralle l to the ground to
help prevent hot oi l from running down your
arm.
- Drain the oil into a container des igned for
this purpose, one large enough to hold at least the total amount of oil in your eng ine .
- Engine oil is poisonous. Keep it well out of
the reach of chi ldren .
- Cont inuous contact w ith used engine oil is
harmful to yo ur sk in. A lways protect your
sk in by washing o il off thoroug hly w ith soap
and water.
@ Note
Never mix o il add it ives wit h your engine o il.
These additives ca n damage your eng ine and
adversely affect your Aud i Lim ited New Veh i­
cle Warranty.
@ For the sake of the environment
- Before changing your oil, f irst make sure
you know w here yo u can properly dispose of
the used oil.
- Always dispose of used engine oil properly. Do not dump it on garden soi l, wooded
324
areas, into open streams or down sewage
drains.
- Recycle used engine o il by ta king it to a used
engine oi l collection facility in yo ur a rea, or
contact a service station.
Cooling system
Coolant
The eng ine cooling system is filled w ith a mixtu re
of p urified wate r and coolant additive a t the fac­
tory. This coolan t m ust no t be no t changed.
The coo lant level is mon itored through th e . in­
dicator light
r=;, page 22. However, we do recom­
mend oc cas io nally checking the coolant leve l
manu ally.
If you must add coolant, use a mixture of water
and coolant additive . Mix ing the coo lant add itive
with dist illed wate r is recommended.
Coolant additive
The coolant additive is made of anti-freezing and
corrosion protection agents . Only use the follow­
i ng coolant additives . These add itives may be
mixed wi th each other.
Coolant additive Specification
G12 evo TL 774 L
G12 ++ TL 774 G
G 13
TL 774 J
The amou nt of coolant addit ive that needs to be
mixed with water depends o n the c lima te where
t h e ve hicle w ill be operated. If the coo lant add i­
t ive pe rcen tage is too low, the coolan t ca n freeze
and damage the engine.
Coolant Freeze protec-
additive tion
Wa rm min
. 40% min. -13 °F
regions max
. 45% ( -25 °C)
Cold min. 50% max. -40 °F
regions max. 55% (-40 °C)

a co ...... N r--. N ...... 0
0
:E ' (D Note
-Before the start of winter, have an author­
ized Audi dealer or author ized Audi Service
Facility check if the coolant additive in your
vehicle matches the percentage appropriate
for the climate . Th is is especially important
when driving in co lder climates.
- If the appropriate coolant additive is not
available in an emergency, do not add any
other additive. You could damage the en­
gine. If this happens, only use wa te r and re­
store the co rrect mixture ratio with the
spec ified coo lan t additive as soon as possi­
ble .
- Only refill with new coo lant.
- Radiator sealant must no t be mixed with
the coo lant.
Adding coolant
Fig . 26 5 Eng ine compartme nt: release button on coolant
expansion tank
Observe the safety precautions ¢ page 319,
Working in the engine compartment .
Checking the engine coolant level
.,. Park the vehicle on a level surface .
.,. Swi tch the ign ition off.
... Read the coolant leve l on the coo lant expansion
tank¢
fig . 265.
... The coolant level must be between the MIN and
MAX markings when the engine in cold. When
the engine is warm it can be slightly above the
MAX marking.
Adding coolant
Requirement: there must be a residual amount of
coo lant in the expans ion tank
¢ (D .
Chec king and Filling
.,. Let the engine cool down.
... Place a cloth over the coolant expansion tank
cap.
... Push the release button
¢fig. 265 and carefu l­
ly unscrew the cap to the left until you feel re­
sistance ¢.&, .
.,. Push the release button aga in and remove the
cap comple tely .
.,. Add coo lant m ixed in the cor rec t rat io
¢page 324 up to t he MAX mar king.
... Ma ke sure that t he f luid level remains stab le .
Add mo re coolant if necessary .
... Tu rn the cap to the right to secure it until you
fee l res istance a second time.
Coola nt loss usually in dicates there is a leak . Im­
mediate ly drive your vehicle to a n authorized
Audi dealer or authorized A udi Service Facility
and have the cooling system inspected.
If the
cooling system is not leaking, a loss can come
from the coolant boiling through overheat ing
and being pushed out of the cooling system .
A WARNING ,.__
-The cooling system is under pressure. Do
not open the coo lant ex pansion tan k cap
when t he engine is hot. This increases the
ris k of burns .
- Th e coolan t addi tive and the coolan t can be
dangerou s to yo ur he alt h . Fo r th is reason,
keep the coolant in the original cont ainer
an d away from children. There is a risk of
poisoning .
- When working in the engine compar tment,
remember that t he radiator fan can switch
on even if the ignition is switched off, which increases the risk of injury .
{U) Note
Do not add coolant if the expansion tank is
empty. There may be air in the cooling sys­
tem, which increases the risk of engine dam ­
age. If this is the case, do not cont inue driv­
i ng. See an authorized A udi dealer or author­
i zed Audi Service Facility for assistance .
-
325

Checking and Filling
Brake fluid
N
N
~ N ,l: CX) al
Fig. 266 Engine compartment: cap on brake flu id reservo ir
Observe the safety precautions c> .&. in Working
in the engine compartment on page 319.
Checking the br ake fluid l evel
~ Read the brake fluid level on the brake fluid
reservo ir
c> page 321, fig . 263 . The brake fluid
level must be between the MIN and MAX mark­
ings
Q ,&. .
The brake fluid level is mon itored automat ically .
Chan ging the b ra ke fluid
Have the brake fluid changed regularly by an au­
thorized Audi dealer or authorized Audi Servic e
Facility .
A WARNING
-If the brake fluid level is be low the MIN
marking, it can impair the braking effect
and dr iving safety, which increase the risk of
an accident. Do not cont inue d riving . See an
authorized Aud i dealer or autho rized Audi
Service Facility for assistance .
-If the brake fluid is o ld, bubbles may form
in the b rake system du ring heavy b raking.
T his would impair brak ing performance and
driving safety, which increases the risk of an
accident.
- T o ensure the brake system functions cor­
rectly, only use brake fluids t hat comply
with VW standard 501 14 or
FMVSS-116 DOT 4 .
(D Note
-If the brake fluid level is above the MAX
mark ing, brake fluid may leak out over the
326
edge of the reservoi r and result in damage
to the vehicle.
- Do not get any brake fluid on the vehicle
paint, because it will corrode the paint.
Battery
General warnings about batteries
Because of the comp lex power supp ly, all wo rk
on batter ies such as d isconnecting, replacing,
etc., sho uld
onl y be performed by an autho rized
Audi dealer or au thorized A udi Servi ce Fac ility
Q _& .
The term "vehicle battery" refers to the 12 Volt
ba ttery in your vehicle.
Detail ed warnings for th e vehicle battery :
Always wear eye protection.
&
Battery acid is highly corros ive. Always
wear protective gloves and eye protection .
So
®
Fire, sparks, open flame and smoking are
forbidden .
£
A highly explosive m ixture of gases can
form when charging batter ies.
®
Always keep children far away from bat-
tery electrolyte and the battery.
~
Always follow the instructions in the oper -
ating manual.
A WARNING
All work on the battery or electrical system in
your vehicle can result in injuries, chemical burns, accidents or burns. Because of this, all
work must be performed
on ly by an author­
ized Audi dealer or authorized Audi Service
Fac ility .
A WARNING
California Proposition 65 Warning:
- Battery posts, term inals and related acces­
sories conta in lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive problems.
Wash hands after handling.
~

a co ...... N r--. N ...... 0
0
:E ' (D Note
-If the vehicle will be p arked for long periods
of time, protect it against t he cold so that it
will not be destroyed by "freezing"
¢ page 327.
- There are electrical components under the
cargo floor behind a trim pane l that warm
up du ring operat ion. To reduce the r isk of
the components overheat ing, do not store
ob jects s uch as blankets u nder the ca rgo
floor. If they overheat, the components will
swi tch off tempo rar ily. Thi s wi ll be indicated
by a message in the ins trumen t clus ter, un­
ti l the temperature returns to normal.
@,l For the sake of the environment
'8' B atteries cont ain poll uti ng substa nces s uch
a s s ulfu ric a cid and le ad. Contact an aut hor­
ize d Au di dealer or a uthorized Aud i Service
Facility for more info rmation.
Vehicle battery
The term "vehicle battery" refers to the 12 Volt
battery in your vehicle.
Not running the vehicle for long periods of
time
If yo u do not dr ive you r vehicle for seve ral days or
weeks, e lectrical equipment is gradually sca led
back or switched off. This reduces ene rgy use and
ensu res the veh icle w ill be able to start after long
pe riods of time¢
page 147. Some convenience
functions, suc h as inter ior light ing or power seat
adjustment, may not be available under certa in
circumstances. These convenience funct ions w ill
be ava ilable again once you switc h the ign ition on
and start the engine.
Even when electrical equ ipment is switched off,
the equ ipment can still d rain the vehicle battery
if the vehicle is not drive n for long per iods of
time. Deep d rain ing results in a chemical reaction
that des troys the inside of the vehicle b attery.
The vehicle batte ry must be charged every mont h
to reduce the risk of this happening ¢
page 327.
Contact an author ized Audi dealer or authorized
Aud i Service Facility for more information.
Chec king and Filling
Winter operation
Co ld wea ther places higher dem ands on the vehi­
cl e battery . This res ults in reduced s tarting ab ili­
ty. Have the vehicle battery checked by an au ­
t h orized Audi dea le r or authorized Audi Service
Facility before the cold time of year.
Charging the vehicle battery
Fi g. 2 67 En g in e compar tmen t: co nnecto rs fo r a c harger
and j ump start cab les
Requireme nt: only use chargers with a ma ximum
charging voltage of 30 amp s/14 .8 Volts .
The
vehicle battery cab les remain connec ted .
.,. Read the warnings ¢
A in General warnings
about batteries on page 326
and ¢ &_ .
.,. Switch off the ignit ion and all electrical equ ip­
ment .
.,. Open the hood ¢
page 320.
.,. Open the red cover on the pos itive termina l
¢fig . 267.
.,. Clamp the charger terminal clamps to the jump
start pins
accord ing to the instructions. (pin
under the red cove r= "positive", pin with he x­
agona l head= "negat ive").
.,. Insert t he power cable for t he charging dev ice
into the socket and switch the device on .
.,. At the end of the charg ing p rocess, sw itch the
charger off and pull the power cable out of the
so cket.
.,. Remove the ch arger termin al cl amps.
.,. Close the red cover on the positive termina l.
.,. Close the hood
¢ page 320 .
327

Checking and Filling
& WARNING
- A highly explosive mixture of gases can form
when charging batter ies . Only charge the
vehicle battery in well-vent ilated areas .
- A drained vehicle battery can freeze at tem­
peratures a round 32 QF (0 QC) . A frozen or
thawed veh icle battery must not be charged
and must not be used anymore. If ice fo rms,
the battery housing ca n crack and ba tte ry
electrolyte can lea k out, which increases the
risk of an explosion and chemi cal bu rns.
Contact an authorized Au di dea le r o r au­
tho rized Audi Serv ice Facility fo r more info r­
mation.
- Do not connect o r disconnect the ch arging
cable while charg ing because this increases
t h e risk of an exp losion.
(D Tips
- Only charge the vehicle battery through the
con nections in the engine compartment .
- Read a ll of t he manufacture r's ins tructions
for the charger befo re charg ing the vehicle
battery.
Windshield washer system
F ig. 26 8 Eng ine co mpa rtment: was her fluid reservo ir cap
The winds hield washer fluid reservoir O contains
the cleaning solution for the windshield and the
headlight washer system*
c> page 321, fig . 263.
The reservo ir capacity can be found in
c:;, page 375.
To reduce the r isk of lime sca le deposits o n the
spray nozzles, use clean water with low amounts
of calcium . Always add window cleane r to the wa-
328
te r. When the outside tempe ratures are cold, an
anti-freezing agent shou ld be added to the water
so that it does not freeze.
(D Note
- The concentration o f anti -freezing agent
must be adjusted to the ve hicle operating
conditions in the respective cl imate. A con­
centration that is too high can lead to vehi­
cle damage.
- Never add radiator anti-freeze or other addi­ tives to the washer fluid.
- Do not use a glass cleaner t hat contains
paint so lvents, because t his could damage
the paint.
Service interval display
The service interval display detects when your ve­
hicle is due for service .
Checking service intervals
You can check the remaining d istance or t ime un­
ti l the next oi l change or next inspection in the
Infotainment system.
.,. Select in the Infotainment system : the
I MENU I
button > Veh icle > left cont rol button > Se rvi ce
& checks > Service inter vals .
Resetting the indicator
An a utho rized Audi deal er or author ized Audi
Se rvice Facility wi ll reset the service interval dis ­
play after performing se rvice .
If you have changed the o il yourself, yo u must re­
set the o il change interval.
.,. Select in the Infotainment system: thel
MENU !
button > Vehicle > left cont rol button > S ervice
& checks > Service intervals > Reset oil change
interval.
I f an o il cha nge or inspection is due, you can ac­
cess i t in the I nfot ainment system . T he display
works in two s tages :
-Service reminder : after a certa in distance is
dr iven, a message appea rs in the instrument

Cl a:, ...... N
" N ...... 0
0
::r ' cluster display every time the ignition is switch ­
ed on . The remaining distance and time is
displayed br iefly.
- Service due : if your vehicle has reached a serv­
ice interval, a message appears briefly after
switching the ignition on.
({;D) Note
-Only reset the oil change indicator if the oil
was changed .
- Following the service intervals is critical to
maintaining t he service life and va lue of
your vehicle, especia lly the engine . Even if
the mileage on the vehicle is low, do not ex­
ceed the time for the next service.
Checking and Filling
329

a co ...... N r--. N ...... 0
0
:E ' Emergency assistance
General information
.. Par k the vehicle as far as poss ible from moving
traff ic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a leve l surface .
It you are on a steep h ill, be especially careful.
.. Set the parking brake .
.. Switch the emergency flashe rs on.
.. Have the passengers exit the veh icle . They
sho uld move to a safe place, for example be­
hind a guard rail.
& WARNING
Follow the steps g iven above. This is for your
protection and the for the safety of o ther driv ­
ers .
Equipment
Vehicle tool kit/tire mobility kit/vehicle
jack
App lies to: veh icles with the vehicle tool kit, tire mobili ty ki t
an d vehicle jac k
The vehicle tool kit, vehicle jack, tire mobility kit
and comp ressor are s to red in the luggage com­
pa rtment unde r the cargo floor cove r. Lift the
cargo floor using the handle.
& WARNING
Impro per use of the vehicle jac k can ca use se­
rious perso nal injuries.
- Never use the screw drive r hex he ad to
tigh ten whee l bolts, since the bol ts cannot
atta in the necessary tighten ing torque if you
use the hex head, potentially ca using an ac­
c ident.
- The factory-supplied jack is i nten ded on ly
for your vehicle model. Under no circ um­
stances should it be used to lift heavy
vehicles or other loads; you r isk injuring
yourself.
- Never start the engine whe n the vehicle is
ra ised, which could ca use a n accident.
- Support the veh icle secure ly with appropr i­
ate stands if work is to be performed under-
Em ergen cy as sis tanc e
neath the vehicle; otherwise, there is a po­
tential risk for injury.
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only su itable for use on the
veh icle it came with.
(D Tips
The vehicle jack in your vehicle is mainte ­
nance-free.
Tire mobility kit
Preparation
.. Read a nd follow the important safety precau-
t ions
¢page 357 .
.. Set the park ing brake .
.. Select the "P" selector lever position .
.. Check if a repair with the tire mobility kit is pos ­
sible
¢ page 357.
Using the tire mobility kit
Fig. 273 Tire: tire damage t hat can not be repaired
T he tire repair is only meant for tempora ry use .
Change the spare tire as soon as possible¢& .
If the t ire is p ierced by an o bject su ch as a nail,
do no t r emove the object from the tire .
T he tire mob ility kit can be used at tempe ratures
as low as -4 °F (-20 °C).
The tire mobility kit may not be used:
- if the tire has cuts or p unctures that are larger
than 0.16 in (4 mm)
(D ¢ fig . 273
-if the rim is damaged @
- if you drove with very low t ire pressure or with-
out air in the tire @ ..,.
357

Cl a:, ...... N
" N ...... 0
0
::r ' Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
~ Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary , the engine can be started by con­
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING -
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
- A dead battery can freeze at temperatures
around 32 °F (0 °C) . If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables. If you do not, this in-
Emergency situations
creases the risk of an explosion and chemi­
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion .
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-Volt rating . The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah " rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen. The battery case may have be weak­
ened.
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c>page 319.
@ Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
( + ) terminals are connected.
369

-When connecting jumper cables, make sure
that they cannot get ca ught in any mov ing
parts in the engine compartment.
- Do not bend over the batteries - danger of
chem ica l burns!
- The battery cell lock ing screws must be
t ightened sec ure ly.
- Be fore you check anything in the e ngine
compartment, a lways read and hee d all
WAR NINGS
q page 319.
(D Note
Impro per hook -up of jum pe r cables can r uin
the gene rato r.
- Always connect POSITI VE (+ ) to POS ITIV E
( + ), and NEGATIVE( -) to NEGAT IVE( -)
g roun d post of t he battery mana ger contro l
u nit.
- Check that a ll sc rew p lugs on t he battery
cells are screwed in firmly. I f not, t ighten
plugs prior to connecting clamp on negative
batte ry terminal.
- Please note that the procedure fo r con nect­
i ng a jumper cab le as desc ribed above ap­
p lies specifica lly to the case of yo ur vehicle
being jump starte d. When you are giv ing a
ju mp s ta rt to anothe r vehicle, do
not con­
n ect the neg ative (-) cab le to the neg ative
(-) t ermin al on the di sch arged b attery @
q fig. 289. In ste ad , securely connec t the
nega tive ( -) cab le to either a solid me tal
com ponent that is f irm ly bolted to the e n­
gine block o r to the engine bloc k itself. If
the battery that is be ing cha rge d does not
vent to the outs ide, escap ing battery gas
could ignite and exp lode!
Towing with a tow truck
General hints
Your Audi requires special handling for towi ng .
The fo llow ing information is to be used by com ­
mercia l tow tr uck operators who know how to op-
~ e rate the ir equip ment safe ly .
...... N ~ - Never tow your Audi, towing will cause dam-,.....
g age to the engine and transmission .
:E ' Emergency situations
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessa ry damage , your Audi
must be transported with a flatbed truck.
- To load the vehicle on to the flatbed, use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
¢ page371 and ¢page 372.
A WARNING
-A veh icle being towed is not safe for passen-
ge rs. Neve r allow anyone to ride in a vehicle
b eing towed, fo r any r eason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig . 290 Front bumper (cover) : installing th e towing loop
Fig. 291 F ro nt bumper (trim): i nsta lling the towing loop
T he threaded o pening for the towing loop is lo­
c ate d on the right s ide of the front bu mper.
.,. Remove the towing loo p from the vehicle tool
ki t
¢ pag e 357.
.,. Press the cap inw ard with brief, forceful pres ­
sure ¢
fig. 290 . The cap will loosen from the
bumper . ..,.
371