remote control AUDI R8 SPYDER 2012 Owners Manual

2 Table of contents Vehicle literature .. .. .. .. .. ... .
About this Owner's Manual ...
Controls and equipment .. ... .
Cockpit ................ .... .. . .
General illus tration .... ... .. .. ... .
Instruments and warning/
indicator lights ........ .. .. .. . .
Ins truments . .. .. ..... ... .. .. ... .
War ning/ indi cator lights ... .. ... .. .
Driver information system .. .
Introduct ion . .. .. ..... ... .. .. ... .
Service interval disp lay . ... .. .... . .
On-Board Diagnostic system (OBD) .. .
T rip computer ............ .. .. .. . .
M enu display ....... ......... .. . .
Lap timer .. .......... ........ .. .
4
5
6
6
6
8
8
11
21
21
22
22
23
25
27
Speed war ning system . . . . . . . . . . . . . 29
Opening and closing .. .. .. .. . .
Keys ........................ .. .
P owe r locking system ............ .
Fr ont lid . .. .. . .......... .. .. .. . .
Ant i- t heft ala rm system ... .. .. .. . .
P owe r win dows .. .. ... ... .. .. ... .
Convertible top .............. .
Convertible top ....... ... .. .. ... .
W ind deflecto r ... .. ... ... .. .. ... .
Rear window . .. .. ..... ... .. .. ... .
Convertible top emergency operation .
Clear vision .. .. ..... ... .. .. ... .
Lights ..... ... . ...... ... .. .. ... .
Inter ior lights .............. .. ... .
Sun visors ...................... .
W iper and washer system ....... .. .
M irrors .. .. ................ ... . .
Di git al compass .... ...... .. .. .. . .
32
32
34
37
3 8
39
4 0
4 0
42
4 2
43
49
4 9
52
53
53
56
57
Seats and storage . . . . . . . . . . . . . 59
Ge ne ral recomme ndat ions ... .. .. . .
P owe r seats ............. .. .. .. . .
H ead res traint s .......... .... ... .
Cup holder .............. .. .. ... . 59
60
6
1
6 1
Asht ray ... .... .. ... .. ..... .... . .
Cigarette lighter/socket . ..... ... .. .
Storage ... .. .. .. .. ... .. .. .. .. .. .
Warm and cold ... .. ..... .... . .
Climate controls .. .. .... .... ... .. .
Heated seats ................... .
On the road ... ... .. ..... .... . .
Steering .. .. .. .. .. ........... .. .
Ig nit ion lock/Ignition switch ....... .
Starting the engine ............ .. .
Stopping the eng ine ............. .
Pa rking brak e .. .. ............... .
Cru ise con trol ... . ... ... .... ... .. .
Audi mag netic ride ............... .
Transm1ss1on .. ... .. ....... ... .
Manua l transm iss ion ......... .. .. .
R t ronic ... .... .. ............. .. .
62
62
62
65
65
69
70
70
70
71
72
72
74
75
77
7 7
78
Parking system . . . . . . . . . . . . . . . . 82
Par king sy stem adv anced
Homelink ® ................... .
Universa l remote cont rol ........ .. .
Safety first .. ....... .......... .
82
8 8
88
91
Driving Safely . . . . . . . . . . . . . . . . . 91
Gener al notes . . . . . . . . . . . . . . . . . . . . 91
P roper oc cupant se ati ng positions . . . 92
D rive r and passenger si de footwe ll . . . 95
Stow ing luggage . . . . . . . . . . . . . . . . . 96
Reporting Sa fety Defects . . . . . . . . . . . 97
Active rollover protection system 99
Safety belts . . . . . . . . . . . . . . . . . . . 101
Genera l notes . . . . . . . . . . . . . . . . . . . . 101
Why safety belts? . . . . . . . . . . . . . . . . 102
Illustrat ing the principle of an
acc iden t . . . . . . . . . . . . . . . . . . . . . . . . 103
How are safety b elts wo rn cor rect ly? . 104
Safe ty be lt pre tensioners . . . . . . . . . . 107
Airbag system . . . . . . . . . . . . . . . . . 109
I m po rtant t hings to know . . . . . . . . . . 109
F ron t air bags . . . . . . . . . . . . . . . . . . . . 113

32 Opening and clo sing
Opening and closing
Keys
Key set
Fig . 27 Key set
Fig. 28 Remote master key : Indicator light
Your Audi comes with four keys c::> fig. 27:
@ two master keys with remote
control
@ one valet key
© one emergency key
M aster key with remot e co ntrol
You can centrally lock and unlock yo ur vehicle
and start the eng ine with the master key with
remote control. To fold the key o ut and back
in place, press the re lease button
c::> fig. 2 7
(arrow).
Valet key
The valet key only fits the lock in the d river's
door and the ignition lock .
If you have to leave
the key with somebody e lse, yo u are well-ad ­
vised to turn
over the valet key only.
Be aware that the front lid and glove compa rt­
ment can be opened from ins ide the ve hicl e
using the release buttons . Emergency key
T he emergency key is only for tempo rary use if
the ve hicle key s hou ld be lost o r misplaced.
Key replacement
If you lose a key, contact your authorized Audi
dealer immed iate ly to have the
lost key disa­
bled . Be sure to br ing all your keys with you .
If a key is lost, you should repo rt it to your in­
surance company .
Reg istered keys
You can inquire about the number of remote master keys registered to your vehicle
r=> page 25 . In this way, you can be certain of
obta ining all the remote master keys if you
purchase a used vehicle .
St ate of maste r key b attery
When a button is pressed, the check light
flashes
c::> fig. 28. If the check light does not
come on or flash, the battery is dead and has
to be replaced .
Battery replacement
r=> page 33.
A WARNING
--
- Do not leave your vehicle unattended
with the key in the ignition lock. Entry by unauthorized persons co uld endanger
you or result in theft or damage the vehi­
cle. A lways lock all doors and take the
key .
- D o not leave ch ildren unattended in the
veh icle, especially with a ccess to ve hicle
keys. Unguarded access to the keys pro­
vides children the opportu nity to start
the engine and/or activate vehicle sys­
tems such as the power windows etc . Un­
supervised operation of any vehicle sys ­
tem by children can result in serious in­
jury .
(D Tips
If you open the driver's door with the key
l eft in the ign ition lock, a ch ime will
sound. This is your reminder to remove the key and lock the door .

Master key with remote control
The remote control allows you to lock or un­
lock the vehicle electronically .
The transmitter and battery are located in the
head of the remote control. The receiver is lo­
cated inside the vehicle . The maximum effec ­
tive range depends on several things . Remem­
ber, if the battery is wea k, the effective range
decreases.
If you need to replace the remote control, or if
you need to have it repaired, you must see
your authorized Audi dealer. Only then can
you use the key again.
(D Tips
- If the ignition is sw itched on, the remote
control system is deactivated .
- The remote control system can be affect­
ed by other systems operating in the
same frequency range close to the vehi­
cle, such as mobile telephones, televi­
sion broadcasting stations, etc.
- Fo r Declaration of Compliance to United
States FCC and Indus try Canada regula­
tions
¢ page 222.
Resetting the remote control
The remote control must be reset if the vehi­
cle does not unlock.
• Press the unlock@ button on the remote
control.
• Within 30 seconds, unlock or lock the vehi­
cle once at the door lock using the stem of
the remote control key.
• Press the unlock button~ or the lock but­
ton ~.
Opening and closing 33
Master key battery replacement
Each master key contains a battery housed
under the cover.
Fig . 29 Remote master key: opening t he cover
We recommend having the battery changed
by an authorized Audi dea ler . However, if you
wish to rep lace the dead battery yourse lf, pro­
ceed as follows:
• Pry apart the base
~ fig. 29@and the cov-
er@ carefully with a coin .
• Remove the cover (arrow).
• Remove the dead battery from the cover.
• Insta ll the new battery. Please make certain
that the"+" sign on the battery faces down
in the cover. Correct polarity is shown on the
cover .
• Place the cover w ith the new battery on the
key base and press both parts together .
@ For the sake of the environment
Dispose of dead batteries properly so as
not to pollute the environment.
(D Tips
The replacement battery must be the
same specification as the origina l.
Electronic immobilizer
The immobilizer helps to prevent unauthor­
ized use of your vehicle .
A computer chip inside your key automatically
deactivates the electronic immobilizer when
you insert the key in the ignition lock . When
you remove the key from the ignit ion lock, the
II>

-In the event of a c rash with airbag de ­
ployment all locked doors will be auto­
matically unlocked to g ive access to the
vehicle occupants from the outside .
- You are we ll advised not to keep valua­
bles inside an unattended vehicle, visib le
or not . Even a properly locked vehicle
cannot p rovide the securi ty of a safe!
Unlocking/locking the vehicle with the
remote control
Fig. 30 Remote co n trol: functio n buttons
To unlock the vehicle~
.. Press button @ once ¢ fig. 30.
To lock the vehicle [ru
.. Press button @ once ¢ /A.
To unlock front lid only
.. Press button © for approximately one sec ­
ond .
PANIC Button
.,. Pu sh the red button @to activate the pan ic
function. The horn sounds and the turn sig­
nal s flash .
.. Push the button @again to deactivate the
panic funct ion .
The turn s ignals flash twice when the vehicle
is unlocked . If the vehicle is un locked and a
door is not opened within the next 30 sec­
onds, the veh icle locks again automatically.
This feat ure prevents the vehicle from be ing
left unlocked accidentally for a long period of
time .
Opening and closing 35
The turn signals briefly flash once and the
horn sounds once wh en the doo rs and front
li d are locked properly.
_& WARNING
Read and follow all WARNINGS ¢.&. in
General description on page 34.
(D Tips
- Use the remote contro l only when the
doors and front lid are closed.
- In order to make sure the locking func­
tion is working, you should a lways keep
your eye on the vehicle to make sure it is
properly locked.
-
- Do not use the remote control if you are
inside the car, otherwise you may unin­
tentionally lock the vehicle, and then you
would set off the anti-theft alarm when
you try to open a door . In case this hap­
pens anyhow, push the unlock button@ .
- Use the pan ic function on ly if you are in
an eme rgency s ituation .
Operating locks with the key
To lock and unlock the vehicle from the out­
side, turn the key in the lock of the driver 's
door .
Fig. 31 Key turn s fo r op eni ng an d clos ing
.. To unlock the vehicle, turn the key to the
opening position
@¢fig. 31.
.. To lock the vehicl e, turn the key in the lock
of the driver's door to the lo ck position @
¢&, . ....

38 Opening and closing
• Reach under the closed glove compartment .
There is a red plastic cord under the glove
compartment.
• Pull the red plastic cord towards you .
Anti-theft alarm
system
Description
The anti-theft alarm triggers on alarm if any ­
one attempts to break into the vehicle .
Fig. 37 Diode posit io n in the instr um ent p anel
The anti-theft alarm system triggers an audi­
ble alarm and turns on the emergency flasher
if an unauthorized interference w ith the vehi­
cle is sensed by the system .
How is the anti-theft alarm system
switched on?
The anti -theft alarm system is switched on
when you lock the driver's door manually us­
ing the fold-out key, or when you use the re­
mote control. The system is activated approxi­
mately 30 seconds after the veh icle is locked.
The indicator light
q fig. 37 starts flashing
rapidly for 2 seconds and then blinks slowly.
How is the anti-theft alarm system
switched off?
The anti-theft a larm system is switched
off
only when you unlock your vehicle. If you do
not open a door within 30 seconds after you
have un locked with the remote contro l, the
vehicle will lock itself again automatically. When will the
anti theft alarm system be
triggered?
When the vehicle is locked, the alarm system
monitors and protects the following parts of
the vehicle:
- engine compartment
- luggage compartment
- doors
- ignition
When the system is ac tivated, the alarm will
be triggered if one of the doors, the engine
compartment lid or the front lid are opened.
The anti-theft alarm system wi ll also go
off
when the battery is disconnected .
You can also trigger the a larm by pressing the
PANIC button on your remote-control key.
This will alert other people in case of emer­
gency . Press the
PANIC button again to turn
off the alarm.
How is the anti-theft alarm switched off
when trigge red?
To switch the alarm
off, press the button @Jon
the master key or switch the ignition on. The alarm will also switch itself off when it comes
to the end of its cycle .
Emergency flasher
The emergency flasher will blink briefly when
the doors, engine compartment lid and front lid are properly closed.
If the emergency flashers do not blink, check
the doors, engine compartment lid and front
lid to make sure they are properly closed. If
you close a door, the engine compartment lid
or the front lid with the anti -theft alarm
switched on , the emergency flashers will blink
only after yo u have closed the door or l id.

58 Clear vis ion
SE (Southeast), S (South), SW (Southwest),
W (West), NW (Northwest).
(D Tips
To avo id ina ccurate directions, do not a l­
low any remote controls, electrical sys ­
tems, or metal parts close to t he mirror .
Setting the magnetic deflection zone
The correct magnetic deflection zone must be
set in order to display the directions correctly.
Fig . 72 Magne tic deflection zone boundaries
.. Hold the @button ~ page 57, fig . 71 down
until the number of the set magnetic deflec­
tion zone appears on the interior rear view
mirror .
.. Adjust the magnetic deflection zone by re­
peatedly pressing on the @button . The set
mode automatically deactivates after a few
seconds.
Calibrating the compass
The compass has to be recalibrated if the dis­
play is wrong or inaccurate .
.. Hold the@ button down until the letter C
is displayed on the inte rior rearv iew mirro r. ..
Drive in a circle at a speed o f abo ut 5 mph
(10 km/h) until a direction is shown on the
interior rearview mirror .
_& WARNING
--
The digital compass is to be used as a di­
rectional aid only. Even though you may
want to look at it while you are driving, you
must st ill pay atte ntion to traffic, road a nd
weather conditions as well as othe r possi­
b le hazards.

88 Homelin k®
Homelink ®
Universal remote
control
General information
The Homelink universal remote control can
be programmed with hand-held transmitters
from existing equipment.
You must first program the Homelink ® trans­
mitter before you can use the system
~ page 88, Programming the Homelink ®
transmitter.
In order to program the Homelink® transmit­
ter for devices utilizing rolling code, a second person on a ladder who can safely reach the
garage door opener motor is recommended.
It is also necessary to locate the "learn" but­
ton on your garage door opener motor . Refer
to the operating instructions for the opener,
as the location and color of this button may
vary by manufacturer .
You can still use the original remote control
for the device at any time.
A WARNING
-
- Never use the Homelink® transmitter
with any garage door opener that does
have not the safety stop and reverse fea­
ture as required by federal safety stand­
ards. This includes any garage door open­
er model manufactured before April 1,
1982.
- A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety standards. Using a garage door
opener without these features increases
risk of serious injury or death.
- For safety reasons never release the
parking brake or start the engine while
anyone is standing in front of the vehicle.
- A garage door or an estate gate may
sometimes be set in motion when the
Homelink ® remote control is being pro­
grammed. If the device is repeatedly ac- tivated, this can overstrain motor and
damage its electrical components
-an
overheated motor is a fire hazard!
- To avoid possible injuries or property
damage, please always make absolutely
certain that no persons or objects are lo­
cated in the range of motion of any
equipment being operated.
{!) Tips
- If you would like more information on
Homelink ®, where to purchase the
Homelink ® compatible products, or
would like to purchase the Homelink®
Home Lighting Package, please call toll­
free: 1-800-355-3515.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions ~
page 222.
Programming the Homelink ®
transmitter
The transmitter is programmed in two phas­
es. For rolling code transmitters, a third
phase is also necessary.
~----------------- ~ ,:.
~
Fig. 101 Overhead console: Homeli nk® keypad
I
'-..~0000 - - ,r.;-_ - -
Fig. 102 Fro nt bumper , driver side : loc ation of trans -
mi tter unit ..,_

Phase 1:
p rogramming th e overh ead k eypad
1. Make sure your vehicle is wit hin operating
range of the remote controlled garage
door opener.
2. Set the parking brake
q A in General in­
formation on page 88.
3 . Turn the ignition on . Do not start the en­
g ine!
4. P ress and hold the two outs ide Home­
Link ® buttons
(D and @for approxi­
mately 20 seconds until indicator light @
¢fig. 101 begins to flash . Then release
both buttons. Do not ho ld the buttons for
longer than 30 seconds.
.,. This procedure only needs to be performed
once . It erases the factory-set default codes
and does not have to be repeated to pro­
gram add it ional remote controls.
S. P ress and hold the Home Link ® button
(D ,
® or @ until the indicato r ligh t@
starts flashing
slowly. Re lease the bu tton.
.,. The system will remain in programming
mode for 5 minutes . Co to the front of the
vehicle and proceed with phase 2 .
Phase 2:
programmin g th e bumper mounted tran s
m itter
6. Hold the original remote control at a dis­
tance between 0 -6 in. (0 -15 cm) from the
bumper below the appropriate headlight
for your vehicle
c:!;> fig. 102 (use the short­
est distance possib le).
7 . A im the remote con trol just be low the
driver sid e head light.
8. P ress and hold the activation button on
the remote contro l.
.,. May be different in Canada.
If so, press and
re-press (cycle) the act ivation button on your
remote control every two seconds.
9. The emergency flashers will flash
three
time s
(after about 15-60 seconds) when
the programm ing is successful. Release
the butto n on the remote control.
.,. To program more devices, repeat steps 4 to
9.
Homelink ® 89
10. Press and hold the tra ined Homelink ®
button and observe the indicator light @
qfig. 101 .
.,. If the indicator light is solid/contin uous,
programm ing is complete and your device
should activate when you press and release
the t ra ined Homel ink® button .
.,. If the ind icator light blinks rapidly fo r 2 sec­
onds and is the n a solid/continuous light,
p roceed w ith phase 3 to program a roll ing
code device.
Phase 3: rolling code programming
.,. A second pe rson on a ladder who can safely
reach the garage door opene r motor is rec­
ommended .
11. Lo ca te the "learn" button on the ga rage
doo r opener motor ( re fer to the operating
instructions for the opener, as t he loca­
tion of t his button may vary by man ufac ­
turer).
12. Press and re lease the learn button on the
garage door opener motor .
.,. Not e: once the button is pressed, there are
30 s econds in wh ich to in it iate the next
step.
13. On t he Homelink ® keypad inside the vehi­
cl e, firmly press and ho ld the Homel in k®
bu tton prev iously programmed in phases
1 and 2 for two seconds and release. Re­
peat this sequence
twice.
.,. Some vehicles may require the press/hold/
release sequence up to three times to com­
plete t he trai ning process .
.,. Homelink ® should now activate your rolling
code equipped device.
If the S m inute time limit is exceeded, the
emergency flash ers will flash one time to in­
dicate that the p rocess has been te rm inated.
In this case, repeat steps 4 t hrough 9.
If the emergency flashers do not flash
three
times (after about lS-60 seconds), program­ ming was not successful. In this case, repeat
steps 4 through 9 .
Remote contro l units for garage door openers
in Canada are set to stop transmitting radio
frequency sig nals afte r two seconds. This t ime
Ill-

90 Homelink®
may not be sufficient for the Homelink ® sys­
tem to learn the radio frequency signal. Per­
form all other steps as described above.
Operating the Homelink ® transmitter
The HomeLink ® transmitter works in the
some manner as the original hondheld re­
mote control that come with the system.
1------------------g: g
N :l',
:l!III !
d ..
-~ ~ H ~
i: ...
Fig. 1 03 Overhead co nsole: Homelink ® keypad
"" Press the appropriate programmed button
(D , ® or @) to activate the des ired remote
control funct ion
c::> &, in General informa­
tion on page 88.
Reprogramming a single button
A HomeLink ® button can be reprogrammed
individually without affecting the other but­ t on allocations.
Programming the overhead keypad
"" Press the app ropriate Homelink ® button
unt il the ind icator light begins flashing
slowly.
Programming the bumper mounted trans
mitter
1. H old the original remote control at a dis­
tance between
0 -5 in . (0 -13 cm) from the
bumper below the app ropriate head light
fo r your vehicle (use the shortest distance
possib le) .
2 . Aim the remote control just below the
driver side head light .
3. Press and hold the activation button on
the remote control.
4 . The emergency flashers will flash
three
time s
(after about 15-60 seconds) when the p
rogramming is successful. Now re ­
l ease the button on the remote control.
"" If the dev ice utilizes a rolling code, p lease
follow phase 3 of
c::> page 88, Programming
the HomeLink ® transmitter
for rolling code
programm ing .
This p rocedu re will ca use the e xisting pro ­
gramming on the Homelink ® button to be
erased!
Erasing the programming of the
Homelink ® transmitter
When you erase the programming, the pro­
gramming on all three of the transmitter
channels with be lost!
"" Perform steps 1 to 4 as described on
~ page 89, Phase 1: programming the over­
head keypad .
When completed, the Homelink ® system will
be in the prog ramm ing mode and is then
r eady to learn the codes fo r remote controlled
devices.
© Tips
- Programmed buttons ca nnot be erased
ind iv idually .
- For security reasons you are adv ised to
erase the programming of the Home­
Link® sys tem before you se ll you r vehicl e.

222 Consumer Information
malfunctions. Because of the way electronic
components are interconnected with each
other, such malfunctions can also have an ad­
verse affect on other systems that are not di­
rectly involved. This means that you risk both
a substantial reduction in the operational
safety of your vehicle and an increased wear of
vehicle parts~.&, .
Authorized Audi dealers will perform this
work in a professiona l and competent manner
or, in special cases, refer you to a professional
company that specializes in such mod ifica­
tions.
_& WARNING
Improper repairs and modifications can
change the way vehicle systems work and
cause damage to the vehicle and serious
personal injury .
(D Note
If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized Audi dealership as soon as
possible.
-
Declaration of Compliance, Telecommu­
nication or Electronic Systems
Radio Frequency Devices and Radiocommuni­
cation Equipment User Manual Notice.
The manufacturer is not responsible for any
radio or TV interference caused by unauthor­
ized modifications to this equ ipment.
Devices
The following devices each comp ly with FCC
Part 15.19, FCC Part 15.21 and RSS-Gen Issue
1:
-Cell phone package
- El ectronic immob ilizer
- Homelink® universal remote control
- Remote control key
- Tire pressure monitoring system
FCC Part 15.19
T his device complies with part 15 of the FCC
Rules. Operation is subject to the fo llowing
two conditions :
(1) This device may not cause harmful inter­
ference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
FCC Part 15.21
CAUTION:
Changes or modifications not expressly ap­
proved by the party responsible for compli­
ance could vo id the user's authority to operate
the equipment.
RSS-Gen Issue 1
Operation is subject to the following two con­
ditions:
(1) this device may not cause interference,
and
(2) this device must accept any interfe rence ,
i ncl uding interference that may cause unde­
sired operation of the device .